similar to: Anyone have BRI working with Asterisk 1.8, Latest DAHDI, LibPRI?

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Hi all, So, we reverted the LibPRI version and tested it, and then tried with the latest version of everything. Still no changes. The BRI line is in PTMP. If we set the configs to PTMP in the genconf_parameters and try it, we get the following: [Jan 21 17:32:20] ERROR[20341]: chan_dahdi.c:12645 dahdi_pri_error: Unable to receive TEI from network! If we set it to PTP (which it is not) we

Hi, Until now I've been using my Digium B410P cards with misdn 1.0.x. I would like to upgrade my systems and am now wondering which is the "best" route to take: - use the latest release of misdn v1 - upgrade to the latest "stable" kernel and use the built-in misdn v2 - use misdn v2 as a seperate package (disable misdn in the kernel) - use dahdi's support for misdn

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all, We have a BRI installation who is experiencing constant echo with the Digium b410p and mISDN. I have adjusted gains, and originally thought that the desktop phones were at fault, although we experience the same problem when a call is bridged out to an external number. I've tried it with 128 taps (the default and I believe the supported

Hello everybody, I try to install -Ubuntu 8.04 server- a B410P and a TDM2400P together with Asterisk 1.4.26-2, dahdi-linux-2.2.0.2 and dahdi-tools-2.2.0. Problem I face is the following one: CLI> module load chan_dahdi.so == Registered application 'DAHDISendKeypadFacility' == Registered application 'ZapSendKeypadFacility' == Parsing

Hi, I need to rebuild a system which has 4 BRI ports and is connected to Point-to-multiPoint lines, in a country where telco often "drop lines for energy savings". I'm planning to use latest 11.4.0 asterisk version along with dahdi and libpri (no misdn). Which version are recommended for Dahdi and Libpri ? My main requirements are, beside having calls coming in and out: - keep a

Hi all, I wanted to switch from my current setup (mISDN) to the native dahdi with b410p support (wcb4xp). All works fine for normal phone calls but not for faxing. Faxes are distorted, if arriving at all, and hylafax logs the usual bad stuff (HDLC frame not byte-oriented.) Our setup uses a digium b410p card with asterisk 1.6, latest libpri and dahdi, hylafax with iaxmodem, and all this on 1

Hi all, I am having trouble setting the signalling method for the B410P using DAHDI. Asterisk complains that it has never heard of 'bri_cpe' or 'bri_net' - but it doesn't mind having 'pri_cpe' etc. ERROR[4294]: chan_dahdi.c:11327 process_dahdi: Unknown signalling method 'bri_net' Dahdi - dahdi-linux-complete-2.1.0.4+2.1.0.2 Asterisk - 1.4.23.1 Libpri - 1.4.9

The DAHDI docs actually include the 'steps' that used to be in Zaptel's 'make b410p'. These steps involve downloading and compiling mISDN. Why re-invent the wheel? Just a thought :-). As for the 100ohm termination bit - it's simply changing a couple of dip switches on the b410p card (as described in the manual). Andy -----Original Message----- From:

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I've just received the following mail: ======================================================================= SETUP Q.931 Message - - CALLED PARTY NUMBER - -- NUMBERING PLAN IDENTIFICATION (Octet 3) - --- 0000 (Unknown) Full Octet = 80'h, you have set to 81'h. TYPE OF NUMBER should also be unknown which I have been told you have

connecting legacy PBX to Asterisk (for the very same reason, those PBX use TE-PTMP). If others could join this thread and say if they agree or not with NT-PTMP being the 2nd most needed mode, would be great. Please, do not hesitate to comment. > > > Right now, I would not preclude the possibility that NT-PTMP support > might be added, but I could not give you a concrete time at which

Hi, Has anyone information about BRI hardware supported by 1.6 libpri ? In another thread, I was told a basic BRI card with HFC chipset (Bewan Gazel 128) was supported but I would delighted to lear about other harwarde (and specifically about Digium B410P). Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Just to add.... P[ 1] Transmitting 128 samples 2 misdn P[ 1] writing 128 bytes 2 asterisk P[ 1] Sending :160 bytes 2 MISDN P[ 0] misdn_jb_fill: written:160 | Buffer status:256 p:861fee0 P[ 0] misdn_jb_empty: read:128 | Buffer status:128 p:861fee0 P[ 1] Transmitting 128 samples 2 misdn P[ 1] writing 128 bytes 2 asterisk P[ 1] PH_CONTROL: channel:1 oad2:07nnnnnnnnn dad0:820055 P[ 1] --> DTMF

Hello all, I'm trying to conect two asterisk servers using two B410p Digium cards. One card on each server. I just setting up the first BRI port on server A as nt_ptp and the first BRI port on server B as te_ptp. I use an ethernet wire to connect the first port of server A (nt_ptp) with the first port on server B (te_ptp) but the port light cotinues blinking on red on both sides once the

Hi, I've been able to make make install the Zaptel drivers (1.2). I'm using a b410p so I executed the following command make b410p. I tried this on multiple machines, but it always failes: root@asterisk:/usr/src/zaptel-1.2.11# make b410p [ -f misdn-b410p.tar.bz ] || wget ftp://ftp.digium.com/pub/zaptel/b410p/misdn-b410p.tar.gz --23:59:54--

Hello, I'm evaluating to possibility to use chan_misdn as a short term workaround, in case latest Dahdi is not stable enough for what we are planning to do (we wish to use Junghanns and Digium BRI hardware with Asterisk 1.6) . I've read www.mISDN.org but still have a couple of questions : 1. Is correct that in a 2.6.27 (and up) enabled kernel, the "embedded" mISDN version is

hello there, I am facing an issue with misd/misdnuser/lcr in the system I am running debian 7 and I managed to install from git misdn/misdnuser but in lcr I am getting: chan_lcr.c: In function 'load_module': chan_lcr.c:3520:24: warning: assignment makes pointer from integer without a cast [enabled by default] make[2]: *** [chan_lcr.po] Error 1 make[2]: Leaving directory

Hi, I'm installing Asterisk on Ubuntu 6.10 When I first compiled the zaptel package I used: make clean make make install So far so good, but the following command failed: make b410p I did some digging on google and found a guide on how to install it manually, but the result was the same. I got these files ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On