similar to: echo when calling to the pstn

Hello all. I have installed AsteriskNow 1.7.1 with all updates. I'm able to make outbound calls without any problem (the external calls are made via an analog line, and the receiver see the CID). However I'm unable to forward incoming calls to the destination I want. What happens is when I make an internal call I ear a "bye". Bellow is the log of the internal call: --

Hello. I don't know if this is a problem, but I was expecting a different behavior. Users, have to dial "0" to get an external line, and afterwords the number they want to dial (exe 12345). The thing is: 1-If user dial "012345" there is an error and the call isn't made and the error is "handle_request_invite: Call from 'XXX' to extension '012345'

Hello all. I have installed AsteriskNow 1.7.1-64bits with freePBX. The system has 1 DAHDi card with 2 analog FXO ports (to pstn) and 1 FXS port connected to a FAX machine. I want the every call received on port FXO-2 to be redirected to the FAX machine. So, what I configured was that every call with DID 12345 (let's suppose that 12345 is the DID connected to the FXO-2)to be redirected to the

Hey folks, I'm from Brazil and I have the following doubt. May I use an asterisk box with some cards to act as an PSTN simutator between a little amount of sites? I will start to think about it in a voice lab for my studies. Kind regards, Vitor -- Vitor Afonso Strabello MSN: vstrabello at hotmail.com

Hi ! I want to install a Telephone IP Avaya 4610SW in my Asterisk 11, but I cant install. It asks a TFTP/HTTP Server, but is necessary I install it in mu Asterisk Server for works my Telephone? The manual is here https://downloads.avaya.com/css/P8/documents/003880182 Thanks in advanced.

Hello everyone, I'm fairly new to asterisk and this list. Currently I'm working on IAX trunks to send/receive calls between 2 asterisk boxes with asterisk 1.6.1.1+asterisk gui 2.0. After some work in the gui, two boxes can send/receive calls to/from the other just fine, the only problem I have is the caller id. Here is my setup: 1. on both boxes, I added an IAX user in the gui, say the

Hi folks, I'm currently running a modified version of Asterisk 1.6.1.1, I observed an unexpected behavior of my system today: 1. SIP device A successfully registered extension 100; 2. SIP device B tried to register extension 100 but with wrong password, so registration failed; 3. A then showed it was unregistered! Failed registration of device B shouldn't kick A off, I expect A stay

Hi there, I need a Python interface to asterisk manager for my own project. The voip-info.org (http://www.voip-info.org/wiki/view/Asterisk+manager+Examples) lists 4 python projects for this purpose: Fats, py-Asterisk, pyst and StarPy. Because my project is rather small and I don't want to involve twisted in, the options left for me are py-Asterisk and pyst. So I want to ask your opinion:

Yes I used. The problem can be the version of Asterisk? I use Asterisk 13 instead of 11. 2016-02-12 14:31 GMT-02:00, Shabbir abbasi <shabbirabbasi92 at gmail.com>: > have changed this > [dongle0] > audio=/dev/ttyUSB1 > data=/dev/ttyUSB2 > > To > > [dongle0] > imei=123456789012345 > > and imei exact same as on your device ? > > On Fri, Feb 12, 2016

Hello all. Can you help me find where the CDR's are being stored? The result of "cdr show status" is: Call Detail Record (CDR) settings ---------------------------------- Logging: Enabled Mode: Simple Log unanswered calls: No * Registered Backends ------------------- (none) Best regards, -vcf

Hi, Complete Asterisk noob here, I just have a few general questions I need to ask before I start installing it: If I want to setup Asterisk simply to respond to echo calls (SIP calls from a softphone only), do I need to install AsteriskNow as well, or can I simply configure dialplan to do that? Thanks, Ali

Humm, thanks for your reply But whats is the code in parkedcalls context. Please, can you give an example? Thanks very much. 2016-02-03 17:15 GMT-02:00, Richard Mudgett <rmudgett at digium.com>: > On Wed, Feb 3, 2016 at 1:05 PM, Vitor Mazuco <vitor.mazuco at gmail.com> > wrote: > >> Hi! >> >> I tried to use Parking Calls >> >> I use Asterisk

Ah no, I'm asking what code I put inside of parkedcalls? This example works? [ramais] include => parkedcalls [parkedcalls] exten => 700,1,ParkedCall(701) exten => 702,1,ParkedCall(702) exten => 703,1,ParkedCall(703) exten => 704,1,ParkedCall(704) This exten works? 2016-02-03 17:27 GMT-02:00, Doug Lytle <support at drdos.info>: >>>> On Feb 3, 2016, at

Humm, so this context parkedcalls is inside on features.conf? 2016-02-03 17:42 GMT-02:00, Doug Lytle <support at drdos.info>: >>>> On Feb 3, 2016, at 2:32 PM, Vitor Mazuco vitor.mazuco at gmail.com wrote: > >>>> Ah no, I'm asking what code I put inside of parkedcalls? > > Nothing, > > The context parkedcalls is generated by features.conf, you just

Hello, I'm Vitor Afonso Strabello and I need to be added as a member into the Wiki to edit/create some tips and entries on the Wiki. My userid is VitorStrabello. I would like to contribute on network, configuration and installation (to begin, I'll post something in kickstart section on the wiki...) tips/tricks/how-tos, so on at the CentOS wiki. Also I'm a member of the CentOSBR

Yes, I used IMEI. But in CLI appearing nothing and it not register. 2016-02-12 14:27 GMT-02:00, Shabbir abbasi <shabbirabbasi92 at gmail.com>: > have you tried imei discovery > imei=123456789012345 > > > write imei number instaed of 12345... > > On Fri, Feb 12, 2016 at 8:51 PM, Vitor Mazuco <vitor.mazuco at gmail.com> > wrote: > >> Hi! >>

Hi, I am using asterisknow 1.5.0 and Wildcard TDM410P card. Everything is working fine except the caller ID of incoming call from PSTN line. The phone display is showing "Unknown" when there is an incoming call. I think the same problem listed here: https://issues.asterisk.org/view.php?id=6683 There is one patch on this link but i don't know how to apply patch on asterisknow.

Hello, Trying to upgrade (from asterisk18-1.8.6.0-1) to the latest RPM version from Asterisk repo I found that asterisknow-version is needed by package asterisk18-core-1.8.7.0-2 How could this be explained? Best regards, Ioan ######### [root at localhost ~]# yum update asterisk18* -x asterisknow-version Loaded plugins: fastestmirror, kmod Loading mirror speeds from cached hostfile * base:

I tried this [dongle0] ;audio=/dev/ttyUSB1 ; tty port for audio connection; no default value ;data=/dev/ttyUSB2 ; tty port for AT commands; no default value ; or you can omit both audio and data together and use imei=123456789012345 and/or imsi=123456789012345 ; imei and imsi must contain exactly 15 digits ! ; imei/imsi discovery is available on Linux only

Hello, Is it possible to detect a hook flash in asterisk. I want to be able to perform some functions an hook flash. I have the following entry in features.conf which executes a Macro on detecting key press '**'. [applicationmap] test => **,caller,Macro,testflash Is it possible to do this action on hook flash? -------------- next part -------------- An HTML attachment was