Displaying 20 results from an estimated 3000 matches similar to: "Callback through extensions.conf?"
2010 Jul 08
1
not sure what to change to point the timing to the at&t circuits?
# Span 1
span=1,1,0,esf,b8zs
bchan=1-23
dchan=24
echocanceller=mg2,1-23
# Span 2
span=2,2,0,esf,b8zs
bchan=25-47
dchan=48
echocanceller=mg2,25-47
# Span 3
span=3,3,0,esf,b8zs
bchan=49-71
dchan=72
echocanceller=mg2,49-71
# Span 4
span=4,4,0,esf,b8zs
bchan=73-95
dchan=96
echocanceller=mg2,73-95
# Global
loadzone = us
defaultzone = us
Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"
2010 Jan 14
2
Dahdi issues
Hello,
My first attempt to get dahdi running on 1.4.28... with a Rhino 8 port
modular card and a single FXS module.
Got the Rhino card installed and the machine sees it:
root at pbx:/etc/dahdi# dmesg | grep rcbfx
[ 71.985309] rcbfx 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ
21
[ 71.985440] rcbfx 1: Rhino PCI BAR0 50100000 IOMem mapped at
ffffc90008d7c000
[ 71.985504]
2009 Apr 02
2
Dahdi, TE220 Device, and Asterisk Problem
Hello!
I am trying to configure my digium TE220 dual-span pci express card
with Dahdi. I seemed to have managed to set up the card with the
Dahdi kernel, as demonstrated by executing dahdi_scan:
[1]
active=yes
alarms=RED
description=T2XXP (PCI) Card 0 Span 1
name=TE2/0/1
manufacturer=Digium
devicetype=Wildcard TE220 (4th Gen)
location=Board ID Switch 0
basechan=1
totchans=31
irq=16
2012 Jan 03
1
ISDN E1, after electrical disconnected is not becoming UP, IRQ misses: 1
Dear All;
I am afraid from IRQ misses: 1
The ISDN E1 was working fine on the machine, the electrical disconnected and then the Red Allarm. I checked the dahdi and I found that I have to reinstall dahdi again and I did. But still not becoming UP.
The output of the cat /proc/dahdi/1 is following (I am afraid from the IRQ misses: 1, so if it is a problem what is the solution)?
[root at CC
2012 Jan 23
1
Timing Slips CRC & E-Bit Errors - Asterisk - Trixbox 2.8.0.4
Hi,
I've searched and searched on the possible problems. If anyone can help me
that would be great.
Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) B8ZS/ESF
CRC4 error count: 4750
E-bit error count: 5023
Timing slips: 72
1 TE2/0/1/1 Clear (In use) (SWEC: MG2)
2 TE2/0/1/2 Clear (In use) (SWEC: MG2)
3 TE2/0/1/3 Clear (In
2009 Aug 24
1
E1 w/ TE420B EC
I keep getting a red alarm when trying to setup asterisk to use my
TE420B EC. I only have a blank context setup in my extensions.conf as
I haven't started to config that until I can clear this red alarm. I
don't have physical access to the server, so I can't go reseat the
modules/card/ethernet cable, though I have hands on location that have
done this a couple times
2009 Feb 09
1
Noisy Ring Back Tone with TE205P card
Hi,
I am having problems with an Asterisk with a Digium TE205P card. The
issue is that the Ring Back Tone is noisy. I am making modem's calls and
this noise influences on the initial negotiation protocol, so modems
have to recall.
My configuration is:
Asterisk version: Asterisk 1.4.21.2
Linux version: CentOS release 5.2 (Final)
Card: Digium TE205P
2007 Feb 28
7
Problem with TE212P
Hello.
I have a TE212 configured in E1 mode.
This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured):
cat /proc/zaptel/2
Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN
25 TE2/0/1/1 Clear
26 TE2/0/1/2 Clear
27 TE2/0/1/3 Clear
28 TE2/0/1/4 Clear
29 TE2/0/1/5 Clear
30 TE2/0/1/6 Clear
2011 Aug 16
1
PRI Problem
I am having a problem with a new PRI turn-up on dahdi 2.5.0 and
asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS,
ESF and the span shows up and ok. This PRI is merely a crossover T1
going into an old DC0 class 5 switch.
I am getting the following errors over and over again
[Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043
my_handle_dchan_exception: PRI got event: HDLC Bad FCS
2009 Dec 04
1
DAHDI issues on 1.4.26.1
Hi,
Running 1.4.26.1 here. I have installed TE420B card in my server, and
followed the appropriate steps (as far as I know to configure it). This
TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling
type.
When I dial out, I get this message:
Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to
create channel of type 'DAHDI' (cause 0
2008 Nov 15
1
PBX -> PRI -> * -> Telco not working
Hello all.
I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box.
NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco
Incomming calls from the telco to the asterisk box to the NEC work fine with
indials and everything. Works sweet.
Outbound from the NEC to the Asterisk box fail. Giving an long dial tone
that then times out.
Ie, pick up NEC handset, dial
2013 Mar 21
2
Need help about round-robin
hello list,
i have installed 2 diguim cards in my server using asterisk 1.4 (i use the
old version with zapata.conf and zaptel.conf)
i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i
want to active the round-robin for span 2 and 6) in order to activate the
WIMAX and FH
please see the configuration below and tell me if there is anything wrong
question 2: what is
2014 Jan 09
2
How to read IRQs and timing slips values
Hi,
On a Asterisk 1.8.12 system working OK for months (>100k calls proceed),
users are complaining for bad audio.
My setup is:
PSTN <--E1/PRI ---> Asterisk <--- E1/PRI---> Siemens HiPath <---E1/PRI
---> PSTN
asterisk -rx "dahdi show version"
DAHDI Version: SVN-trunk-r10414 Echo Canceller: HWEC
asterisk -rx "pri show version"
libpri version: 1.4.12
A
2011 Apr 02
1
Problem getting TDM400P clone card to go off-hook and dial
I am having problems getting a Nicherons TDM400P wildcard clone to dial out.
Everything appears to be configured correctly, but although I see call
progress, it never seems to actually pick up the phone.
(The following is a test of 911 emergency, where I substitute 811 [repair
service] as the actual number dialed.)
*CLI>
-- Executing [911 at from-internal:1]
2013 Oct 31
2
issue with dahdi_channels.conf
Hello list
i have an issue with my dahdi_channels.conf
in span 1 when i use it like below i can do my outband calls without issue
; Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER)
group=0,11
context=from-pstn
switchtype = euroisdn
signalling = pri_cpe
channel => 17-31
context = default
group = 63
but when i add in channel 1-15 like: channel => 1-15,17-31
i receive all
2010 Aug 23
1
Dahdi install gone wrong
The card you installed has FXO or FXS modules in it ????? are you getting
your lines directly from the telco co???
Doug D
On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent:
* -----Original Message-----
* From: Todd Reese
* Reply-to: Asterisk Users Mailing List - Non-Commercial
Discussion
* To: asterisk-users at lists.digium.com [3]
* Subject: [asterisk-users] Dahdi
2009 May 19
2
Unable to make outbound calls
I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2
I've got a 2 port T2XXP card attached with on T1 currently plugged in.
Inbound calls work fine, but outbound fail with the rather cryptic:
[May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable to
create channel of type 'DAHDI' (cause 0 - Unknown)
There are similar threads I've found on the
2009 Sep 20
1
Experience with Sangoma's USBfxo
Hi,
I've seen this USB product from Sangoma :
http://www.sangoma.com/products_and_solutions/hardware/analog_telephony/usb_fxo.html
Is it working ok ?
Is it easy to integrate it with Asterisk ?
How would you rate your experience with it ?
Regards
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
2016 Mar 25
2
PRI error "ROSE REJECT"
PRI debug of the entire call would be great, also, switchtype would be
awesome as well.
Thanks!
Matthew Fredrickson
On Thu, Mar 24, 2016 at 4:07 PM, Carlos Rojas <crt.rojas at gmail.com> wrote:
> Hi
>
> Did you activate the pri debug on the cli asterisk?
>
> On Thu, Mar 24, 2016 at 12:59 PM, Carlos Chavez <cursor at telecomabmex.com>
> wrote:
>>
>>
2011 Mar 18
2
Problem routing call to fax machine on DAHDI FXS port
I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS
modules. I'm trying to set-up things to route analog fax calls from a
FXO port to an analog fax machine on a FXS port on the same card.
Outgoing faxes work just fine. But incoming faces are routed to the
right DAHDI extension, but the call dropped right as the fax machine
rings for the first time. The fax machine