similar to: B410P: DAHDI BRI PTMP HDLC Abort (6) on Primary D-channel of span 1 (TEI Errors)

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Hi, I'm experiencing difficulties to get a B410P running with Asterisk 10.3.1 and DAHDI 2.6.1. Am I supposed to use DAHDI for this card and ISDN BRI for my country (Belgium)? thx, BC

We are seeing the message " PRI Error on span 1: Received MDL/TEI management message, but configured for mode other than PTMP" on one of our Asterisk boxes on a PRI. A Google search turns up a number of hits for this error, but they are all for BRI not PRI. I'm reasonably sure there are no recent updates or config changes. Running Asterisk 1.4.37. We can update to 1.4.44 if it

HI, I'm using asterisk-1.4.24, dahdi-linux-complete-2.4.0+2.4.0 and libpri-1.4.11.4 When dial, when 492131 answer, in console appear some error messages -- AGI Script Executing Application: (DIAL) Options: (DAHDI/g1/492131|60) -- Requested transfer capability: 0x00 - SPEECH -- Called g1/492131 [Dec 4 11:15:59] WARNING[7669]: chan_dahdi.c:1776 dahdi_enable_ec: Unable to enable

I'm running 1.8.2 rc1 on a Centos box with dahdi-linux-complete 2.4, using the wct4xxp module. All operations appear normal however I noticed an error repeating occasionally on the console. [Jan 10 13:53:05] ERROR[6906]: chan_dahdi.c:13691 dahdi_pri_error: 1 ROSE RETURN ERROR: [Jan 10 13:53:05] ERROR[6906]: chan_dahdi.c:13691 dahdi_pri_error: 1 INVOKE ID: 11 [Jan 10 13:53:05] ERROR[6906]:

Dear Customer Support, i connected the asterisk to a e1 interface of our hipath4000. outgoing calls from a sip peer of my asterisk to an up0 telephone which iss connected to the hipath4000 are working. If you want to dial from an up0 device to the e1 interface where asterisk is connected to, you have to use the prefix 83. But when you enter the 3rd cipher this error appears at the cli

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

Hi, My setup is: IPPhone1 --- Asterisk1 with B410P ---- Patton 4638 --- Asterisk2 --- IPPhone2 I want to evaluate Asterisk1 in TE/PtmP mode. So, Patton box is configured in NT/PtmP (with 3 BRI links between both systems). Anyway, asterisk -rx "pri show spans" keeps replying : PRI span 1/0: Provisioned, Down, Active PRI span 2/0: Provisioned, Down, Active PRI span 3/0: Provisioned,

Hi, I've read that the new dahdi channel supporting B410P doesn't support PtmP when in NT mode. Does it support PtmP when in TE mode ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081209/f422b5d0/attachment.htm

Hi, As you may know, these ISDN BRI features are very important here in Europe as ISDN Basic Rate Access is very popular among Small & Medium Entreprises. I don't really know why but it seems that in many countries, default is to install small PBX using Point-to-Multipoint (PtMP) mode as opposed to Point-to-Point (PtP) which is the norm for PRI. So basically, in several countries, SME

Hi, In my lab, I'm testing BRI spans in NT/ptmp mode. My setup is: asterisk 11.2.1 libpri 1.4.14 dahdi 2.6.1 wctdm24xxp (HA8 hybrid with B400M) SIP phone <----> Asterisk with HA8 <----> Patton SN4638 <----> Asterisk <----> SIP phone The single BRI line I'm testing remains down: CLI> pri show spans PRI span 1/0: In Alarm, Up, Active I'm quite certain this

Hi, In BRI/TE/PtmP mode, pri show span 1 used to display "Type: CPE (PtMP)" (setup is bristuffed 1.2 asterisk) It seems, it displays now "Type: CPE" without any mention to PtMP (with asterisk 1.6). I'm far from 100% sure it used to include the PtMP word but do you think it should display it ? Does it make sense ? Regards -------------- next part -------------- An HTML

I'm using QSIG between Asterisk and an NEC SV8300. Whenever I make a call from the SV8300, I see: [Oct 4 21:02:49] ERROR[5729]: chan_dahdi.c:12226 dahdi_pri_error: !! < Unknown IE 50 (cs5, len = 3) I see an IE 50 in the Q.932 specification, so I don't understand why this error is occuring.

Hello, Is it possible, for testing, to connect an cat5 straight patch cord between 2 ports of a Digium B410P card and use these 2 ports as a normal dahdi trunk ? I've tried this: One port is set as NT, the other as TE. I would expect timing to come for system hardware so I choose in /etc/dahdi/system.conf : span=1,0,0,ccs,ami span=2,0,0,ccs,ami Results: - both ports lights are green -

Hi, I'm getting the following error from an asterisk 1.6.0.9 installation: [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: Asked to delete sched id -1??? [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: No more room in scheduler This repeats a few times, then asterisk crashes. I can't seem to locate any info on this error at all. I'm using

getting some errors on my test system. this is 1.4 (Asterisk SVN-branch-1.4-r214194) with a 4 port T412p card. Three of the ports are connected: Span 1 to the PSTN on a 10 channel bearer line, ports 2 and 3 are cross-overed (!) to each other. Port 4 is not plugged in. This has been working fine for several months. I updated a few days ago to the latest 1.4 branch. However, now I cannot dial into

Starting from today i am receiving the following errors on asterisk.. What can be the reason for it? [May 7 11:45:16] ERROR[14885]: chan_dahdi.c:10515 dahdi_pri_error: ACK received for '0' outside of window of '3' to '4', restarting [May 7 11:45:16] WARNING[14885]: chan_dahdi.c:3347 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel

Hello List, I just turned up a T1 with Qwest. All the channels came up and inbound and outbound work and sound great. The only issue I have is this message "Handling message for SAPI/TEI=0/0" repeated on the console a couple times a second. I tried googling it but only found links to code in libpri. I am running Asterisk SVN-trunk-r76015M. I am going to upgrade to the latest

What happens if you change to: signalling=bri_cpe_ptp -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Alex Sent: 01 October 2010 11:37 To: asterisk-users at lists.digium.com Subject: [asterisk-users] debian/dahdi/zaphfc - Unable to receive TEI fromnetwork! Hello, <snip> # cat

Hi, I suddenly started to receive an error like [Aug 4 14:26:57] ERROR[2477]: chan_dahdi.c:10515 dahdi_pri_error: No more room in scheduler [Aug 4 14:26:57] ERROR[2477]: chan_dahdi.c:10515 dahdi_pri_error: Asked to delete sched id -1??? and it went on till i reboot asterisk and dahdi services.. I wonder what caused this error, because there were no physical problem between pbx and asterisk