similar to: Asterisk 1.4.38 - unknown signalling bri_cpe

Hello, Using libpri-1.4.7 and asterisk-1.6.0.1, I've got "Unknown signalling method 'bri_cpe" when "module load chan_dahdi.so". Googling with "chan_dahdi bri_net" don't help much. Shall I upgrade to 1.6.1rcXXX to get 'bri_cpe" support ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, It seems BRI signalling settings are missing from http://www.voip-info.org/wiki/view/Asterisk+config+chan_dahdi.conf I would like to add those parameters : bri_cpe_ptmp bri_cpe bri_net Is this http://www.voip-info.org/wiki/view/Asterisk+config+chan_dahdi.conftied to a specific Asterisk version ? Can I edit this ? Regards -------------- next part -------------- An HTML attachment was

Hi all, I am having trouble setting the signalling method for the B410P using DAHDI. Asterisk complains that it has never heard of 'bri_cpe' or 'bri_net' - but it doesn't mind having 'pri_cpe' etc. ERROR[4294]: chan_dahdi.c:11327 process_dahdi: Unknown signalling method 'bri_net' Dahdi - dahdi-linux-complete-2.1.0.4+2.1.0.2 Asterisk - 1.4.23.1 Libpri - 1.4.9

Is there a recommended way to find out the cause of DIALSTATUS = CONGESTION for PRI/BRI channels? Currently I am evaluating the DIALSTATUS variable and I also count the active ISDN channels for the ISDN trunk in question. Counting the active ISDN channels seems somewhat clumsy as the mapping to a specific trunk must be done by hand (or write even more code). I have a setup where outgoing calls

Greetings folks- I'm experiencing issues with a freshly installed box. When a call comes in via PRI (Sangoma AFT-A104), I see this in my logs: [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 12 (Invalid argument) [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 8 (Invalid argument) [Dec 15 14:26:10]

Hi, these are my first steps with DAHDI and I finally managed to get asterisk to load chan_dahdi (after I found out, that I need libpri). But how do I tell chan_dahdi on which isdn numbers it should react? I haven't found a parameter like "incomingmsn" for chan_capi in the documentation. Thanks for your help, Stefan

Hello out there, I'm running an Asterisk 1.8.15-cert1 with DAHDI. Today I noticed that Asterisk is signalling to the calling party the current internal CallerID whenever I put a call to another internal phone. Example: Customer calls 020212345-555 -> IVR answers and puts caller to the chosen queue -> Someone picks up the phone (Internal ext. 321) -> CallerID shown on customers

Hello everybody, I try to install -Ubuntu 8.04 server- a B410P and a TDM2400P together with Asterisk 1.4.26-2, dahdi-linux-2.2.0.2 and dahdi-tools-2.2.0. Problem I face is the following one: CLI> module load chan_dahdi.so == Registered application 'DAHDISendKeypadFacility' == Registered application 'ZapSendKeypadFacility' == Parsing

HI, I'm using asterisk-1.4.24, dahdi-linux-complete-2.4.0+2.4.0 and libpri-1.4.11.4 When dial, when 492131 answer, in console appear some error messages -- AGI Script Executing Application: (DIAL) Options: (DAHDI/g1/492131|60) -- Requested transfer capability: 0x00 - SPEECH -- Called g1/492131 [Dec 4 11:15:59] WARNING[7669]: chan_dahdi.c:1776 dahdi_enable_ec: Unable to enable

Hi, I have a B400P BRI card with point-to-point connection (signalling: bri_cpe) with this dmesg: http://pastebin.com/sXrRt1yM When i restart asterisk server, the card cannot connect to the telco, the control led flashes red. If I unplug the cable between the ISDN nt and the card and wait 40 sec, the card can connect and works properly. The telco says the asterisk crashes the connection

Hi! I have an analog line connected to my asterisk and when I try to answer a call I get this -- Starting simple switch on 'DAHDI/7-1' -- Executing [s at from-pstn:1] Answer("DAHDI/7-1", "") in new stack -- Executing [s at from-pstn:2] Playback("DAHDI/7-1", "vm-intro") in new stack -- <DAHDI/7-1> Playing 'vm-intro' (language

Hi, I have 2 servers: one is running 2 B410P cards with 8 euroisdn lines (mISDN) connected on it, everything runs fine. I prepare a new server - HP 360 G8- with 2 HA8 cards each of them 1 module of 4 lines. Already had with this machine an RMA on both cards as they was faulty and crashed the server. What happends is that when I connect cables on the HA8 modules (those cables are unpluged

So, I've compiled and installed libpri-1.4.11.5, dahdi-linux-complete-2.4.1+2.4.1 and asterisk-1.6.2.17.1, but chan_dahdi is not getting built. If I do a "make menuselect" in asterisk I see it listed with XXX, meaning that dependencies are not met. XXX chan_dahdi Depends on: res_smdi(M), dahdi(E), tonezone(E), pri(E), ss7(E), openr2(E) res_smdi gets built fine, dahdi is

Sir, i am using goautodial server , bri card is showing ok but when i try to call that showing below , This configuration is in doing in dubai , so kindly help me how can connet the call from this , what is my mistake is in this :::chan-dahdi.conf [channels] #include dahdi-channels.conf language=en context=default usecallerid=yes hidecallerid=yes callwaiting=yes usecallingpres=yes

Hi I was using the delivered Ubuntu 1.6.x packages but I wanted to look at gtalk integration so I downloaded, compiled and installed the source (after removing the Ubuntu packages) have installed the following: asterisk-1.8.0 dahdi-linux-complete-2.4.0+2.4.0 libpri-1.4.11.5 I copied my config back into place and most seems to work, but I cannot get my phone that is plugged into the Wildcard

Hi, I'm experiencing difficulties to get a B410P running with Asterisk 10.3.1 and DAHDI 2.6.1. Am I supposed to use DAHDI for this card and ISDN BRI for my country (Belgium)? thx, BC

Hello, I'm experiencing some weird problems on my server: - 1) The following messages are filling up my logs: [Sep 29 08:24:59] WARNING[7077]: chan_dahdi.c:2789 pri_find_dchan: No D-channels available! Using Primary channel 140 as D-channel anyway! [Sep 29 08:24:59] WARNING[7078]: chan_dahdi.c:2789 pri_find_dchan: No D-channels available! Using Primary channel 171 as D-channel anyway!

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)