similar to: Dahdi 2.4.0 and unplugged spans [SOLVED]

Hi, I'm facing an issue with which loading wctdm24xxp module fails. Here is relevant dmesg's output : [ 13.455729] dahdi: Telephony Interface Registered on major 196 [ 13.455729] dahdi: Version: 2.4.0 [ 13.510847] ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 22 [ 15.527788] wctdm24xxp 0000:01:0b.0: Timeout waiting for receive frame. [ 17.527787]

Hi, On a Lenny system, with dahdi 2.4.0, libpri 1.4.11.5 and asterisk 1.6.1.18, I inserted a new Digium HA8 + B400M card. My usual installation fails. I can see it listed : # lspci -n | grep d161 01:0b.0 0200: d161:8007 (rev 11) # lspci -vn 01:0b.0 0200: d161:8007 (rev 11) Subsystem: d161:8007 Flags: medium devsel, IRQ 22 I/O ports at d400 [size=256] Memory at

Hi list, I installed 2 HB8 cards each of them with a Quad Bri modules in a HP 360 G6 running Debian Squeeze. Here is an output of dmesg wafter server has booted: [ 9.784123] wctdm24xxp 0000:0b:08.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31 [ 11.847073] bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex [ 11.847600] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [

2011/6/14 Kevin P. Fleming <kpfleming at digium.com> > On 06/14/2011 03:11 PM, Olivier wrote: > >> Hi, >> >> 1. Is there any manual entry about modprobe's options relative to a >> given Dahdi driver (wctdm24xxp, for instance) ? >> >> 2. When loading a wctdm24xxp driver, is there any parameter to pass to >> modprobe to configure a span in

Hi, In my lab, I'm testing BRI spans in NT/ptmp mode. My setup is: asterisk 11.2.1 libpri 1.4.14 dahdi 2.6.1 wctdm24xxp (HA8 hybrid with B400M) SIP phone <----> Asterisk with HA8 <----> Patton SN4638 <----> Asterisk <----> SIP phone The single BRI line I'm testing remains down: CLI> pri show spans PRI span 1/0: In Alarm, Up, Active I'm quite certain this

Hi, 1. Is there any manual entry about modprobe's options relative to a given Dahdi driver (wctdm24xxp, for instance) ? 2. When loading a wctdm24xxp driver, is there any parameter to pass to modprobe to configure a span in NT/point to point mode ? 3. After running dahdi_cfg -vvvvv , I can read with dmesg : [ 1986.289277] wctdm24xxp 0000:04:06.0: xhfc: Configuring port 0 span 1 in TE mode

Hi, On a (bogus) system equiped with a Digium HA8 and 8 BRI ports, I'm reading this: # asterisk -rx "dahdi show status" Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO HA8-0000 RED 109 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) HA8-0000 UNCONFI 109 0

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux and DAHDI-Tools version 2.4.0. DAHDI-Linux 2.4.0, DAHDI-Tools 2.4.0, and DAHDI-Linux-Complete are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux and DAHDI-Tools version 2.4.0. DAHDI-Linux 2.4.0, DAHDI-Tools 2.4.0, and DAHDI-Linux-Complete are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In

Hi All, This is a request for testing for users of Asterisk 1.4 or 1.6 with any of the following Digium VoiceBus based cards: TDM2400P, AEX2400, AEX800, TDM800P, TDM410, TE120P, TE121, and/or TE122. From a practical standpoint, this branch should allow these boards to work in more systems / configurations where IRQ misses caused problems in the past. The updated wctdm24xxp and wcte12xp

Hi, If you have a custom kernel (and therefore have duplicates of everything in /kernel in your custom kernel) and have noticed that when you try to use anonymous tracing, dtrace adds multiple copies of the forceload directives to /etc/system, e.g.: * vvvv Added by DTrace * * The following forceload directives were added by dtrace(1M) to allow for * tracing during boot. If these

The Asterisk Development Team is pleased to announce the first release of DAHDI-Linux 2.6.0 and DAHDI-Tools 2.6.0. 2.6.0 is a feature release which: - Adds support for the TE820 8-span card to the wct4xxp driver. - Decrease load time of analog cards supported by the wctdm24xxp driver. - Adds sysfs object model to facilitate persistent span numbering and early loading of modules

The Asterisk Development Team is pleased to announce the first release of DAHDI-Linux 2.6.0 and DAHDI-Tools 2.6.0. 2.6.0 is a feature release which: - Adds support for the TE820 8-span card to the wct4xxp driver. - Decrease load time of analog cards supported by the wctdm24xxp driver. - Adds sysfs object model to facilitate persistent span numbering and early loading of modules

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux 2.5.0.2 and DAHDI-Tools 2.5.0.2. 2.5.0.2 is a bug fix release. It is recommended that current users of v2.5 to upgrade. DAHDI-Linux 2.5.0.2, DAHDI-Tools 2.5.0.2, and DAHDI-Linux-Complete 2.5.0.1+2.5.0.1 are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux 2.5.0.2 and DAHDI-Tools 2.5.0.2. 2.5.0.2 is a bug fix release. It is recommended that current users of v2.5 to upgrade. DAHDI-Linux 2.5.0.2, DAHDI-Tools 2.5.0.2, and DAHDI-Linux-Complete 2.5.0.1+2.5.0.1 are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux

2017-03-14 15:26 GMT+01:00 Tzafrir Cohen <tzafrir.cohen at xorcom.com>: > On Tue, Mar 14, 2017 at 02:58:07PM +0100, Olivier wrote: > > 2017-03-14 13:08 GMT+01:00 Tzafrir Cohen <tzafrir.cohen at xorcom.com>: > > > > > On Tue, Mar 14, 2017 at 11:10:57AM +0100, Olivier wrote: > > > > Hello, > > > > > > > > After all these years

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux 2.5.0.1 and DAHDI-Tools 2.5.0.1. 2.5.0.1 is a bug fix release. It is recommended that current users of v2.5.0 upgrade. DAHDI-Linux 2.5.0.1, DAHDI-Tools 2.5.0.1, and DAHDI-Linux-Complete 2.5.0.1+2.5.0.1 are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux 2.5.0.1 and DAHDI-Tools 2.5.0.1. 2.5.0.1 is a bug fix release. It is recommended that current users of v2.5.0 upgrade. DAHDI-Linux 2.5.0.1, DAHDI-Tools 2.5.0.1, and DAHDI-Linux-Complete 2.5.0.1+2.5.0.1 are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.2-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux 2.6.2-rc1 is a bugfix release of which the most noteable changes are: - Fix compile error on RHEL 5.2 / Centos 5.9 and later - Development switch from svn to git Issues closed in this release: DAHLIN-314

The Asterisk Development Team has announced the release of: DAHDI-Linux 2.6.2 DAHDI-Tools 2.6.2 DAHDI-Linux-Complete 2.6.2+2.6.2 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete 2.6.2 is a bugfix release of which the