similar to: HA8 + B400M not configured with genconf_parameters

Hi, 1. Is there any manual entry about modprobe's options relative to a given Dahdi driver (wctdm24xxp, for instance) ? 2. When loading a wctdm24xxp driver, is there any parameter to pass to modprobe to configure a span in NT/point to point mode ? 3. After running dahdi_cfg -vvvvv , I can read with dmesg : [ 1986.289277] wctdm24xxp 0000:04:06.0: xhfc: Configuring port 0 span 1 in TE mode

2017-03-14 13:08 GMT+01:00 Tzafrir Cohen <tzafrir.cohen at xorcom.com>: > On Tue, Mar 14, 2017 at 11:10:57AM +0100, Olivier wrote: > > Hello, > > > > After all these years installing from source, I'm giving Dahdi package > > installation a try on a recent Stretch box. > > > > Google over the web, I didn't find too many doc on this topic. >

2017-03-14 15:26 GMT+01:00 Tzafrir Cohen <tzafrir.cohen at xorcom.com>: > On Tue, Mar 14, 2017 at 02:58:07PM +0100, Olivier wrote: > > 2017-03-14 13:08 GMT+01:00 Tzafrir Cohen <tzafrir.cohen at xorcom.com>: > > > > > On Tue, Mar 14, 2017 at 11:10:57AM +0100, Olivier wrote: > > > > Hello, > > > > > > > > After all these years

2011/6/14 Kevin P. Fleming <kpfleming at digium.com> > On 06/14/2011 03:11 PM, Olivier wrote: > >> Hi, >> >> 1. Is there any manual entry about modprobe's options relative to a >> given Dahdi driver (wctdm24xxp, for instance) ? >> >> 2. When loading a wctdm24xxp driver, is there any parameter to pass to >> modprobe to configure a span in

Hi, I'm reading Digium HA8 manual (page 55). It lists several parameters that can be used to configure a BRI port. More precisely, it suggests that : Term, is the last parameter NT/TE is the one just before (starting from the end). If I'm not mistaken, it seems dahdi_genconf generates /etc/dahdi/system.conf files in which both parameters order is reversed : # Span 1: WCBRI/0/0

Hi, I'm facing an issue with which loading wctdm24xxp module fails. Here is relevant dmesg's output : [ 13.455729] dahdi: Telephony Interface Registered on major 196 [ 13.455729] dahdi: Version: 2.4.0 [ 13.510847] ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 22 [ 15.527788] wctdm24xxp 0000:01:0b.0: Timeout waiting for receive frame. [ 17.527787]

Hi, I'm using revision 6822 of Dahdi Tools. # dahdi_hardware pci:0000:05:06.0 wcb4xxp+ d161:b410 Digium Wildcard B410P # asterisk -rx "dahdi show version" DAHDI Version: 2.2.0.2 Echo Canceller: OSLEC # cat /etc/dahdi/genconf_parameters ... pri_termtype SPAN/1 TE SPAN/2 TE SPAN/3 NT SPAN/4 NT #

Hello, 1. How can specify in /etc/dahdi/genconf_parameters file that a port from a B410P board is to be "disabled". Playing with comments (see bellow) doesn't help : file /etc/asterisk/dahdi-channels.conf is filled with 4 ports data. pri_termtype SPAN/1 TE SPAN/2 TE SPAN/3 TE # SPAN/4 TE 2. How can specify groups in

Hi, On a (bogus) system equiped with a Digium HA8 and 8 BRI ports, I'm reading this: # asterisk -rx "dahdi show status" Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO HA8-0000 RED 109 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) HA8-0000 UNCONFI 109 0

Hello, After all these years installing from source, I'm giving Dahdi package installation a try on a recent Stretch box. Google over the web, I didn't find too many doc on this topic. 1. Is this one [1] up-to-date ? Reading Stretch I would say a single asterisk-dahdi would be enough to install asterisk dahdi and libpri. 2. On my box, the following fails. What would you suggest ?

Hello, I just installed a Debian Jessie box from scratch which sports a Digium TE435 digital card. I installed the software, built and loaded the kernel modules: # dpkg -l|grep dahdi ii asterisk-dahdi 1:11.13.1~dfsg-2+b1 amd64 DAHDI devices support for the Asterisk PBX ii dahdi 1:2.10.0.1-1 amd64

Hi, In my lab, I'm testing BRI spans in NT/ptmp mode. My setup is: asterisk 11.2.1 libpri 1.4.14 dahdi 2.6.1 wctdm24xxp (HA8 hybrid with B400M) SIP phone <----> Asterisk with HA8 <----> Patton SN4638 <----> Asterisk <----> SIP phone The single BRI line I'm testing remains down: CLI> pri show spans PRI span 1/0: In Alarm, Up, Active I'm quite certain this

Hello group, I am installing Asterisk on a new pc running Ubuntu 12.04.3 Server. ?I have dahdi-complete-2.7.0.1+2.7.0.1, and have tried 2.6.1 and 2.8.0-rc1 and 2.8.0-rc2. ?I am following along in the ASTERISK The Definitive Guide 4th Edition and on page 116 when I issue the command $ sudo /etc/init.d/dahdi start I get the following error: Loading DAHDI hardware modules: ? ?wctdm24xxp: done

Hello, I am trying to install my E1 card to make a conection with an Ericsson MD-110 PBX. I installed dahdi drivers as: dahdi_hardware pci:0000:04:08.0 wcte12xp- d161:8000 Wildcard TE121 ran dahdi_genconf and it created all my e1 ports. On the other side i also configured the pbx to communicate with TE121. On ericsson side, i have no error messages. On asterisk side, no error messages. But

Hi all! I'm new with telephony cards and DAHDI drivers. I have installed Asterisk NOW 3.0.0 and update to Asterisk 11.7.0, modules are update too. I'm following the installation guide of Atcom [1] for AX1600P analogic card, modules are loaded [root at pbx ~]# lsmod | grep -E "hisax|netjet|dahdi" netjet 14618 0 isdnhdlc 4523 1 netjet mISDNipac

Hi All, I have installed asteriskNow with Asterisk 1.6.2.11 and FreePBX 2.7.0.10. I have configured x100p fxo card in my asterisk box. But in my cli mode i am not getting the command *"dahdi show status"* Output of CLI : astrisks*CLI> *dahdi show status* No such command 'dahdi show status' (type 'core show help dahdi show' for other possible commands) I

Hi, I know this may sound a bit silly but, given some asterisk issue are still open (see http://issues.asterisk.org/jira/browse/ASTERISK-13176 for instance), I'm wondering if there is a recommended way to configure an used port from a Digium HA8 + B400M board. At the moment, my console is full with messages such as : [Jun 15 09:06:25] WARNING[2140]: chan_dahdi.c:3369 pri_find_dchan: No

I just installed a TE820 octal span T1 card, and it's not showing up in dahdi_hardware output. This was installed into a test machine that already has a TDM800P card in it, and that one is showing up and working fine. Is there some kernel module that I'm missing? Lspci: 05:04.0 Ethernet controller: Digium, Inc. Wildcard TDM800P 8-port analog card (rev 11) 21:08.0 Communication

Hi, I have 2 servers: one is running 2 B410P cards with 8 euroisdn lines (mISDN) connected on it, everything runs fine. I prepare a new server - HP 360 G8- with 2 HA8 cards each of them 1 module of 4 lines. Already had with this machine an RMA on both cards as they was faulty and crashed the server. What happends is that when I connect cables on the HA8 modules (those cables are unpluged

2011/6/15 A J Stiles <asterisk_list at earthshod.co.uk> > On Wednesday 15 Jun 2011, Olivier wrote: > > At the moment, my console is full with messages such as : > > [Jun 15 09:06:25] WARNING[2140]: chan_dahdi.c:3369 pri_find_dchan: No > > D-channels available! Using Primary channel 9 as D-channel anyway! > > [Jun 15 09:06:25] WARNING[2141]: chan_dahdi.c:3369