similar to: Asterisk Playback sound dropping on linphone

hi all, please help... I am calling in the simplest way among two linphone clients connected to one asterisk server... the call ends on one side without any sign of problem, while on the other side it stays connected. I checked the SIP dialogue and at some point the server sends a BYE message to one party I have no timeout set, though the duration of a call is always around 20s. the two

Hi, I've got this PXA270 board set-up with Linphone 1.2.0 and am trying to get linphonec to work with Asterisk. I have the echo test working, but when I dial in to this, to voicemail or anything else using Playback() to play a sample, I hear nothing for ages (10-15 secs) and then little sections. With the echo test, I get the tail of the message (...pressing the pound

Hi There, i think all VOIP clients for Linux are unusable! i got testet: Linphone + Linphonec all in version 12.2 Kphone gophone and other... the only programm that is usable is gnomemeeting... does anybody knew some other tools? Best Regards, Mark

I'm building a paging system composed of roughly 10 switches in daisy chain, with an embedded box with a speaker and a microphone for each switch. The embedded box runs my software. I need the system to be resilient to any network partition, so that anyone can send announces from any mic to all the reachable clients. I'd need also to page a subset of all the speakers. I'm

Hello I am trying to connect linphone 0.12.2 to an * 0.9.1 box over a LAN using the console version of linphone. both boxs are using the latest alsa drivers on a LFS kernal 2.4. I am running into errors with codec compatability between linphone and *. A point to note is that I am able to connect to asterisk using other sip phones noteably sjphone however linephone is giving me

I am dying here with linphone (not sure if it is crap software or just me being an idiot) but out of the box debian installations of two linphones fail with a "Got SIP response 415 "Unsupported Media Type" back from 192.168.1.3" Can anybody recommend a particular SIP soft phone that broadly satisfies the following criteria? 1. Run on linux. 2. Simple to use and setup. 3. Is

Hi, I'd like to implement some way of controlling remote SIP clients while in a call, to execute remote commands. The call topology (think of a PA system) is this: * the caller is in a MeetMe() conference room * the callees are Page()d, then the dynamic conference room is connected to the previous one I'm wondering if Asterisk is relaying DTMF (SIP info or RTP) from the caller to the

Hi folks an issue I don't understand. I'm running * stable 1.0.3 on public internet, with following iax.conf / sip.conf entries: iax.conf [100] type=friend username=Foo context=default auth=md5,plaintext,rsa secret=secret host=dynamic callerid="Foo" <100> qualify=no sip.conf [10] type=friend username=Bar context=default callerid=Bar <10>

Hi All, I am getting this error during make. please help me./ speexec.c: In function `speex_ec_process': speexec.c:112: syntax error before "noise" cc1: warnings being treated as errors speexec.c:133: warning: implicit declaration of function `speex_echo_state_reset' speexec.c:148: warning: passing arg 5 of `speex_echo_cancel' makes pointer from integer without a cast

Today's "frustrated programmer" award goes to Linphone, which has the following debug output: > (linphone:28655): LinphoneCore-WARNING **: this fucking remote sip phone did not answered properly to my sdp offer! I get this message when I connect to linphone using a softphone, or when I try to use linphone to connect to asterisk and listen to an announcement. I suspect that

Hi John, 1. Could you get any further, in your quest for working BLF with linphone ? 2. Have you tried with a different Linphone version (4.12 is pending on Linux, packaged as an AppImage, or 4.11 exists on iOS/Android/Win10) ? Best regards Le mer. 25 mars 2020 à 15:06, John Hughes <john at calva.com> a écrit : > > On 23/03/2020 18:51, Joshua C. Colp wrote: > > On Mon, Mar

It seems a new Linphone 4.2 is to be published next week ! Hopefully, ... Le ven. 5 juin 2020 à 13:34, John Hughes <john at calva.com> a écrit : > On 26/05/2020 15:33, Olivier wrote: > > Hi John, > > 1. Could you get any further, in your quest for working BLF with linphone ? > > The patches to get linphone-3.12 BLF working with Asterisk are here: > >

Hello. Calls cancelled by caller during the dialing phase, are shown in Linphone as simply past calls, not missed ones. I thought this is an Linphone issue, but Sylvain says it's on my PBX side: https://github.com/BelledonneCommunications/linphone-android/issues/832#issuecomment-557474864 > The CANCEL message has a Reason header with Q.850 protocol and cause 0, which doesn't mean

Hi all - I am using asterisk 13.27.0 with Linphone. I turned off all codes on linphone except the one I want to try. For example: opus and speex (so only one enabled at a time). Then did this same on asterisk for the linphone extension. disallow=all allow=speex (for example). Then I place my call and the call fails. if I enable something like gsm, ulaw, alaw the call works fine. Why does the

So I've got a bit further with my  project to get BLF working between asterisk and linphone. Initially asterisk was rejecting linphone's SUBSCRIBE messages because they didn't have an Accept: header. I've fixed that and now the initial SUBSCRIBE messages work and I see all my online contacts in green. But after a few minutes linphone attempts to renew the subscriptions and

nautiluz wrote: >I am starting project to develop open implementation of some (naturally open >codec) for simply designed embedded devices which can be used by small to >big VoIP operators or hobbyists which wants to build their own small and >low cost VoIP phone. >Speex seems to be great choice. And greater will be if there should be >some guys who want to help ;-). Sorry

I'd like to cobble together a videophone from an analog phone, connected to an Asterisk FXS channel, and a co-located video camera, connected to a video grabber card on the Asterisk server (so I have a Linux video device providing the video stream). When a call is made from the phone, I'd like to somehow add the video and produce a SIP video call. I don't want to use any sort of

Hi Sergio On 16.10.20 at 07:54 sergio wrote: > Sometimes, linphone shows missed calls as missed. Look like asterisk > replies with cause=487 that time, but I can't understand why. > > Grandstream always shows calls as missed ones. > > How should I investigate this? You could try to reproduce it while activating pcap traces and analyze it afterwards - or you could

Hi, I have * working with X-Lite and Sipura adapters, but I have one person who is linux based, and is trying to use Linphone and Kphone. His end works, but I get very bad echo on my end. Have any of you folks been able to get linux based soft phones working well with *? I'd appreciate links to howtos/docs if you have them, and/or samples of working configs for * and the linux

Hello, has anyone running a linphone-application on am335x (like beaglebone) with opus codec. My CPU has extreme high load, wenn ist start with opus codec. Is there a possibikity tu optimize f?r this single core ARM? Thanks Helmut Sholz ______________________________ BAYERISCHER RUNDFUNK Rundfunkplatz 1 80335 M?nchen HA IT und Medientechnik Abteilung Systemservice Funkhaus FG Sendungssysteme