similar to: Astribank Configuration Issues

Hello Mailinglist, we have a Xorcom Astribank which is installed at our client and working since 10/2008. Suddenly last week there where odd behaviors, no calls going through (it is used to route calls to GSM Gateways). Upon testing (reinitialization of the complete gear) it turned out that one call get's through and then nothing more. I have nothing in the logs, indicating that Asterisk

I'm trying to use a Xorcom Astribank wth Ubuntu 8.04, but got no success. I can see the channel bank with lsusb, but when I tried to use zaptel_hardware, or when I try the /etc/init.d/script, they don't see my Channel Bank. I compiled the latest Zaptel 1.4.10, with Astribank's dependecies, fxload and libusb-dev. Anyone have a similiar experience ? Best Regards, -- Guilherme Loch G?es

Hi Guys, An 8 channel Astribank is connected to Trixbox 2.8 and I ran freepbx-module-zapauto but I get the following when running these commands and can't make calls out: [Trixbox]# dahdi_genconf xpporder /usr/sbin/dahdi_genconf: warning - OLD DRIVER: missing '/sys/bus/xpds/devices/00:0:0/timing_priority'. Fall back to /proc pbx*CLI> dahdi show channels Chan Extension Context

Hi All Just a quick check on the best way to ensure multiple cards/devices load in the correct order. Asterisk 1.8 with Sangoma A101 had no problems until we introduced an Astribank. root at pabx377:/etc/asterisk# dahdi_hardware -v usb:001/004 xpp_usb+ e4e4:1162 Astribank-modular FPGA-firmware LABEL=[usb:X1060395] CONNECTOR=@usb-0000:00:1d.7-3 XBUS-00/XPD-00:

H all... I have an Astribank (8FXS/16FXO), IBM X3200 M2, Asterisk-1.6.2.1, dahdi-linux-complete-2.2.1, libpri-1.4.10.2, centos-5.4 final. My problem is, every time i unplug the astribank power supply, and reconnect it, astribank cannot work again (lsusb result is 11x0)... but, after reinstall the asterisk and dahdi, astribank will detected (lsusb result is 11x2)... any suggestion? Regard,

Hi, all My Asterisk uses a Digium TE120Pand I would like to add an Astribank zaptel_hardware sees is, but I cannot get it working pbx:~# zaptel_hardware Argument "IRQ" isn't numeric in numeric comparison (<=>) at /usr/local/share/perl/5.8.8/Zaptel/Span.pm line 114. usb:005/002 xpp_usb- e4e4:1131 Astribank-8/16 USB-firmware pci:0000:04:00.0 wcte12xp+

I am running Asterisk on Ubuntu 2.6.32-25-server with asterisk 1.6.2.5-0ubuntu1 and dahdi 2.2.1-0ubuntu2. The machine has a passive HCF-based PCI ISDN card and an Astribank 8 attached. The ISDN card works fine. root at servaction:~# lsusb Bus 001 Device 002: ID 04b4:8613 Cypress Semiconductor Corp. CY7C68013 EZ-USB FX2 USB 2.0 Development Kit root at servaction:/usr/share/dahdi# ./xpp_fxloader

Hello, I'm in the process of building an Asterisk machine and need 5 or 6 BRI-Channels. I was looking for the beroNet and Junghans cards and stumbled upon the Xorcom Astribank xBRI products. Has anybody tried out the Astribank xBRI-Channel Banks? Are they production ready or should I go with a beroNet BN8S0 or JUNGHANNS.NET octoBRI ISDN? Thanks in advance, Lars -- We don't like their

My equipement : 2x tdm 400p /4FXO/4FXS 16 PORT ASTRIBANK My first TDM400p is the sync master, so i set astribank to sync to it, but the quality is bad, like it is going fine and second after >>ROBOVOICE ;) any other devices (isdn/sip/tdm cards) are working fine, looks like astribank dont like to be sync 'slave'. Is there any way to change sync master manually, so every another

Hello, I've one astribank with 8 FXO unit and 8 pstn lines connected to the astribank. When I receive calls on my ipphone I get always Unknown callerid. It's is possible to receive the callerid from the lines on the astribank unit? This is my config: [channels] language=es context=from-zaptel signalling=fxs_ks ;rxwink=300 usecallerid=yes callerid=asreceived ;cidsignalling=bell

I have a server with 8 Xorcom Astribank, they're connected to the server via a USB hub, my problem is: when a reboot the server the ID of the Channel Bank changes, cousing a big mess on my server. Anybody know how can I solve this ? Best regards, -- Guilherme Loch G?es Visite nossa loja virtual: http://www.shopvoip.com.br Not?cias e F?rum sobre VoIP com software livre:

Hi all, I'm interested in buy a Astribank-32 but i never heard about detection of far-end disconnection. Does anyone have some experience about that functionality in this hardware ? Thanks in Advance, Gleidson Antonio Henriques

Hello, I'm writing here hoping to have a hint from Asterisk/Digium packager maintainer, Jason Parker (of course that any other's opinion is welcomed). We have installed an asterisk machine using Asterisk and Digium repos. Unfortunately we have found that an Astribank could not be connected due to the lack of the firmware files May 18 14:19:22 tenora1 kernel: usb 1-6: new high speed USB

Hi, I have upgraded an Asterisk installation with a Xorcom BRI Astribank that was working under Ubuntu 8.04 to Ubuntu 9.10 and the device is no longer initialized. When I reload the udev rules, I see that the rules seems to be correctly loaded: udevd[452]: reading '/etc/udev/rules.d/40-xpp.rules' as rules file However, these rules do not seem to be triggered: # udevadm trigger

Hello, I just made a asterisk / dahdi fresh install on Debian 8.4, and ended up with the following packages : $ sudo dpkg -l|grep -Ei 'dahdi|asterisk|libpri' ii asterisk 1:11.13.1~dfsg-2+b1 amd64 Open Source Private Branch Exchange (PBX) ii asterisk-config 1:11.13.1~dfsg-2 all Configuration

Hello, I am trying to update to dahdi 2.2.1. But somehow the xorcom (2BRI) device does not want to work. I pasted below the information I have. pbx at loicvoip1:~# /usr/share/dahdi/xpp_fxloader reset pbx at loicvoip1:~# /usr/share/dahdi/xpp_fxloader usb 'xpp_fxloader'[4937]: --------- FIRMWARE LOADING: (usb) [1 devices] ..Got all 1 devices 'xpp_fxloader'[5003]: ---------

Hi guys, This has been bugging me for days and I can't figure out what's happening. Using the same channel on DAHDI, I can't make a call after previous one being hung up by remote side. However, it works like it should if my end hangs up the call. To make things interesting, DAHDI, or astribank rather, seems to "reset" itself after receiving an incoming call on that DAHDI

lspci | grep Digium 03:05.0 Ethernet controller: Digium, Inc. Wildcard TE122 single-span T1/E1/J1 card (rev 11) dahdi_scan So I have a card in a box - lspci shows it... dahdi_scan reports nothing. Is my card dead? Jerry -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm having trouble getting a xorcom set up. A large part of the problem is that the box is a _long_ way away and I can't get to/at it easily, so while I could probably fix this in a few hours if the machine were in front of me, I'm struggling over a slow unreliable laggy link. Ok, enough whining from me. I have a new Xorcom plugged into the usb of a Suse 11 machine I built Dahdi

Hi, I have a Xorcom Astribank connected to my Asterisk server. In one of the Astribanks FXO port I have a Celular Interface Module. My problem is the Astribank is receiving a early answer from the module, which doesn't happen with a ATA connected to the same module. This is causing some trouble with my billing system. I already tried the answeronpolarityswitch option, what else can I do ?