similar to: OpenVPN over TCP 1194 rather than UDP 1194 - Is there an adverse effect when running Asterisk?

How do I insert the iptables rule below using firewalld? I'm moving up from CentOS 6 to 7 on an office gateway and I'm trying to get OpenVPN working to allow home workers to access PCs at the office. I've got it all working but only by manually inserting an ACCEPT rule in the FORWARD iptables chain: iptables -I FORWARD 3 -i tun+ -j ACCEPT This rule was extracted from my iptables

----- Original Message ----- > From: "Administrator TOOTAI" <admin at tootai.net> > To: asterisk-users at lists.digium.com > Sent: Thursday, April 30, 2015 4:43:33 PM > Subject: Re: [asterisk-users] OpenVPN Clients Intermittently Cannot Call In > > > I am running Asterisk 11.12.0 on CentOS 6.4. The asterisk server and > > internal phones are located on

Hello, I am running Asterisk 11.12.0 on CentOS 6.4. The asterisk server and internal phones are located on the 10.10.32.0/21 LAN subnet. I have many internal SIP phones, which appear to be working correctly. I have a few external phones (Yealink SIP-T32G or other Yealink model) on 192.168.32.0/24 which have an OpenVPN client configured on them that connects back to the LAN network through a

----- Original Message ----- > From: "Administrator TOOTAI" <admin at tootai.net> > To: asterisk-users at lists.digium.com > Sent: Friday, May 1, 2015 6:42:38 AM > Subject: Re: [asterisk-users] OpenVPN Clients Intermittently Cannot Call In > > Le 01/05/2015 00:05, Andrew Martin a ?crit : > > ----- Original Message ----- > >> From:

Hi folks, I have OpenVPN (respect for it developers) running on my FW. Is has two external NICs and on internal everything is fine, except I want OpenVPN (UDP port 1194) going not via default route/network interface. I use such commands: iptables -t mangle -D POSTROUTING -o eth0 -p udp --dport 1194 -j MARK --set-mark 0x990 ip rule add fwmark 0x990

Hi Everyone, Knowing that running Asterisk on an embedded board like the Alix2d3 requires some fine tuning. Do you know of any good guides out there that does this from beginning to end? Looking to run this in a small office environment. Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm setting up a VPN using Samba's AD for user authentication. Everything seems to check out on the PFsense side. Authentication is reported as successful, but when I try to connect to the actual network, I get: "Certificate does not have key usage extension." "certificate verify failed" Is this an issue with samba's self generated certificates or I should I be

Hello All, I would like to use OpenVPN with Samba 4 AD using the LDAP Auth plugin. However, my tests come up with the following errors in the OpenVPN... LDAP bind failed: Strong(er) authentication required (BindSimple: Transport encryption required.) Unable to bind as CN=VPN Connect,CN=Users,DC=MYDOMAIN,DC=COM LDAP connect failed. PLUGIN_CALL: POST

Your pfSense firewall has OpenVPN built into it already, and you can point pfSense authentication back to your samba AD. We support over 400 users in this model. The configuration file for OpenVPN is common to all users, and they authenticate with their AD credentials. > On Mar 14, 2020, at 7:21 AM, Michael Howard via samba <samba at lists.samba.org> wrote: > > On 14/03/2020

> Am 15.03.2020 um 08:21 schrieb S?rgio Basto via samba <samba at lists.samba.org>: > > ?On Sat, 2020-03-14 at 07:43 -0700, gabben via samba wrote: >> Your pfSense firewall has OpenVPN built into it already, and you can >> point pfSense authentication back to your samba AD. We support over >> 400 users in this model. The configuration file for OpenVPN is common

I only have some experience with OPNsense but maybe you can relate: - In my case it was always the certificate.? - I had to add the cert to the system certs using CLI. Adding them in the WebGUI was not enough. - Port 636 did not work for me, only 389 using STARTTLS Hope that helps... On 16. March 2020 at 08:13:50, Stefan G. Weichinger via samba (samba at lists.samba.org) wrote: Am 15.03.20 um

A little off topic, but this does revolve around Samaba. I'm hoping someone can help me get to a working aolution. I haven't been able to find a clear quide, but it must have been done by others. I'm trying to use setup a VPN using OpenVPN on Pfsense with authentication via my Samba AD (Version 4.9.4-Debian) I keep getting a "Could not connect to LDAP server" error when

Probably not the best place to ask, but hopefully someone can point me in the right direction. I have a tiny business. We use Samba for file sharing and authentication in an AD setup. I'm running a pfsense appliance firewall. NAT on the internal network. Is there a way to allow employees to authenticate and access files to encourage remote work? What resource should I look to to figure

Hello I''m hoping you guys can help me figure this out. When I use shorewall clear my windows openvpn client connects perfectly every time. But when I have the shorewall up 90% (not every time) it will connect for about a second and then the connection will reset and that will repeat over and over so i never don''t really get a steady connection at all. I can tell you that

I'm scratching my head here a little. And my post to the openvpn mailing list is not getting any attention. I have an openvpn server working with Windows clients and I thought I'd try to get a client config on a CentOS box running. The client is a minimal install of CentOS and I like to use shorewall (3.2.x). I've tried to run the vpn client with the fw off and on with no change.

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 On 05/05/2015 10:59 AM, Andrew Martin wrote: > > > ----- Original Message ----- >> From: "Administrator TOOTAI" <admin at tootai.net> To: >> asterisk-users at lists.digium.com Sent: Friday, May 1, 2015 6:42:38 >> AM Subject: Re: [asterisk-users] OpenVPN Clients Intermittently >> Cannot Call In

Le 01/05/2015 00:05, Andrew Martin a ?crit : > ----- Original Message ----- >> From: "Administrator TOOTAI" <admin at tootai.net> >> To: asterisk-users at lists.digium.com >> Sent: Thursday, April 30, 2015 4:43:33 PM >> Subject: Re: [asterisk-users] OpenVPN Clients Intermittently Cannot Call In >> >>> I am running Asterisk 11.12.0 on CentOS

Hi Everyone, I am using pfSense to do firewall and NAT on an Asterisk server. I have ports 5060 TCP/UDP and 10k-20k UDP forwarded to the Asterisk server local IP 192.168.5.5. However, when a user from outside using Linksys WRP400 ata connects to the Asterisk server and registers I see them as 192.168.1.1 in the "sip show peers" command. In face, all many different of the Linksys WRP400