similar to: Problem routing incoming from-pstn calls using different contexts

I'm running an AsteriskNow V1.7.1 with both a PSTN connection and fax machine. Both are connected to a DAHDI board. I'd like to route incoming PSTN fax calls to the extension of the fax machine and process non-fax calls through different dialplan.logic. What's the best way to go about doing this? I've looked into Fax for Asterisk, bit I'm not sure that I want it or NVFax

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

[18884732963 at from-fax-machine:... - your call is hitting the from-fax-machine context - yet your 'fax' exten is in the from-pstn-4 context. See the "[2011-03-17 13:40:29.6] NOTICE[8825] chan_dahdi.c: Fax detected, but no fax extension" line. When Asterisk detects an incoming fax tone - it tries to automagically route the call to the 'fax' extension in the SAME

My AsteriskNow box was updated to Centos 5.6 (2.6.18-238.5.1.el5) and DAHDI doesn't want to load. I've tried building it from the sources, but get this error message: CC [M] /root/Desktop/dahdi-linux-complete-2.4.1.1+2.4.1/linux/drivers/dahdi/xpp/card_bri.o In file included from /root/Desktop/dahdi-linux-complete-2.4.1.1+2.4.1/linux/drivers/dahdi/xpp/xpd.h:31, from

Some of you may remember seeing my issue using SIP for incoming calls from the PSTN: http://voip-info.org/wiki-Asterisk+cisco+FXO i.e. all incoming calls arrive in the default 'bogon-calls' context. Well, I tried again using H.323 & get exactly the same result (both for chan_h323 & chan_oh323) i.e. all attempts to put a type=peer in sip.conf or a type=user in h323.conf for

Hello, I am using chan_capi and would like * to behave differently depending on the MSN the caller dials. Is there a way to route incoming ISDN calls to different contexts based on the MSN dailled? I have tried something like msn=1234 incomingmsn=1234 context=msn1 msn=4567 incomingmsn=4567 context=msn2 in capi.conf but with no results. Thanks for any hints. -Walter -- Walter Doerr

> I have 2 FXO channels from which I want to route incoming calls to > different contexts in extensions.conf. I edited the context entries in > dahdi-channels.conf and created matching entries in extensions.conf. > One channel is routed to the new context as I want, but the other > channel is stuck going to the default "from-pstn" context no matter what > I do. >

Calls that come in on DAHDI FXO ports are routed to [context], extension 's' INSTEAD, I would like to route specific ports to specific extensions, For example: I want DAHDI/1-1 to go to 1234 I want DAHDI/1-2 to go to 2345 I want DAHDI/1-3 to go to 3456 ...etc What is the CLEANEST way to do this? Yes, I can create a private context for each DAHDI channel but that seems messy and

Hi, We've been working a lot with Asterisk in SIP for over 6 months but I've finally succumb to the pressure of H.323. I need to find a way to do what we do with SIP but with H.323. That is to have calls from H.323 peers placed into their own unique context (unique to the endpoint placing the call into Asterisk) within Asterisk so this is obviously done using REGISTER's within SIP but

Folks, I have a Merlin Legend R7 V10.0 with a 2 100D cards. I have 1 card in slot 4 going to CenturyTel, and the card in slot 10 going to a flip cable to a TE110P card in a Asterisk 1.6.x box. I have routing setup on the Merlin to send a block of numbers to the Asterisk. Currently the PSTN can dial the Asterisk Extensions. The Asterisk can dial Merlin Extensions. The Merlin can Dial Asterisk

Incoming calls from my Sipura 3000 don't seem to be correctly routing to Asterisk (or something?) Here is my Asterisk configuration for my incoming PSTN line: Code: [1000] type=friend host=dynamic context=incoming secret=6769 dtmfmode=rfc2833 disallow=all allow=ulaw insecure=very Inside of extensions.conf, I have this: Code: [incoming] exten => s,1,Answer( ) exten =>

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! I am trying to redirect to a local extension the incoming calls that I receive to an account which I have in iptel.org, but when receiving I'm obtaining this error: alderamin*CLI> -- Executing [300 at from-internal:1] Dial("SIP/danib-089f8820", "SIP/300|30|tTrm") in new stack [Feb 19 19:22:50] WARNING[19254]:

I am trying to configure Asterisk for BSNL, india network. I have successfully configured it for outgoing calls. When any outside number make any call to trunk then it receives the call properly but when the call is disconnected by inside extension then outside phone does not get a busy tone. Asterisk incoming call log: -- Executing [s at incoming:2] Dial("Zap/4-1", "Zap/1")

Dear all, I am from Saudi Arabiya and I am using digium hardware with asterisk 1.6. When I am executing following AMI originate API. Orginate start to execute extenstion without knowing of PSTN(FXO) channel is ringing. Any one can help me to resolve this issue ? Action: Originate Channel: Dahdi/g0/2923878 Context: outbound-ivr Exten: 1234 Priority: 1 ActionID: ABC45678901234567890

I'm trying to get a MP-114 FXS/FXO gateway working with Asterisk. It registers fine and I can call between the MP-114 and other extensions, but I'm not having much luck with the FXO ports. syslog shows the problem to be in the MP-114 configuration. Can anyone help?

I'm running Asterisk 1.2.13 on a Solaris 10 X86 box behind an IPCop firewall on a 5Mbps down/512 up cable connection. I'm having sound quality problems when users call in for voicemail and with music on hold. The sound is choppy and muffled while souding pretty good for calls inside the network. I'd appreciate some pointers as to where to start looking to improve things. I've

I'm looking into the dialplan specifics: tleilax:~ # tleilax:~ # cat /etc/asterisk/extensions.conf [general] static=yes writeprotect=no [globals] CONSOLE=Console/dsp ; Console interface for demo TRUNK=DAHDI/r1 ; Trunk interface TRUNKX=DAHDI/r2 ; 2nd trunk interface TRUNKIAX=IAX2/ASTtest1:test at 10.10.10.16:4569 ; IAX trunk

READ READ READ .... http://www.asteriskdocs.org/en/3rd_Edition/asterisk-book-html-chunk/asterisk-DP-Basics.html Regards, Mitul Limbani, Business Head, Enterux Solutions Pvt. Ltd. 110 Reena Complex, Opp. Nathani Steel, Vidyavihar (W), Mumbai - 400 086. India http://www.enterux.com/ http://www.entvoice.com/ email: mitul at enterux.in DID: +91-22-71967196 Cell: +91-9820332422 On Sun, Feb 22,

Using 1.6.2.1 with a TDM400, attached to internal analog phones and PSTN. When I dial out to PSTN, I cannot send tones, like push "1" for something stupid. The call itself works, but the DTMF tones fail. -- Starting simple switch on 'DAHDI/1-1' -- Executing [6258013 at internal:1] Answer("DAHDI/1-1", "") in new stack -- Executing [6258013 at

Hello all. I have installed AsteriskNow 1.7.1-64bits with freePBX. The system has 1 DAHDi card with 2 analog FXO ports (to pstn) and 1 FXS port connected to a FAX machine. I want the every call received on port FXO-2 to be redirected to the FAX machine. So, what I configured was that every call with DID 12345 (let's suppose that 12345 is the DID connected to the FXO-2)to be redirected to the