similar to: BLF/Call Pickup using SPA942, SPA962, SPA932

We are having an issue with the SPA962/932 combo where the phone and the sidecar will reboot unexpectedly ? could be onhook, could be on a call, doesn?t seem to matter. I read that certain early firmware revisions could cause this so I?m running what was a week ago the newest available (5.1.18). A call to Linksys support suggested that I ensure that the phones are using a recent firmware version

Greetings list, We recently installed some Linksys SPA962 + SPA932 sidecars into a client's offices. The BLF functionality works fine, but call pickup using the BLF is something of an issue. Following the advice on voip-info.org, I configured part of their dialplan as follows: exten => _**2XX,1,Pickup(SIP/${EXTEN:2}) exten => _**2XX,n,Dial(SIP/${EXTEN:2},15,tw) exten =>

Hi, We have a user who is putting large call volumes through Asterisk, and wants to BLF monitor up to 90 extensions. We are struggling to find a handset that can keep up with Asterisk :) 1) Is there a handset that will do this? 2) Is there a different (standard) way to send BLF and allow directed pickups? 2a) Or even a handset specific way? Asterisk handles the BLF volume fine, even on quite

Hello all, I am using Linksys SPA942 in my current installation activity. I see a peculiar behavior: A call is made and the SPA942 uses its speaker. When the far end of a call hangs up , the SPA942 stays off hook, and after a time plays a fast busy. The user then has to press the line presence button to hang up the phone. I think I must be missing some sip.conf parameter. My sip.conf is pretty

Greetings all. First off, thank you for your time on this. I have spent literally 12 hours searching every forum and article I can find, and I'm going cross-eyed, so I need to bother everyone with this. I am running * 1.2.37, and I am trying to get the hints working, so I can turn one of my SPA962's LED's red when someone parks a call. I have used Button #3 on my SPA962 to

Hi all, I have had (what I consider) an odd request. The installation I'm working on now is an office on a multi-floor building. They 're looking for some kind of solution with the phone system to provide door control. We are a non-profit so of course I'm looking for something VERY inexpensive. I'm sure /someone/ has done something like this. I'd appreciate any ideas. Cassius

Hello, I have an installation in Austria; ISDN service provided by Austria Telekom. The main number of the service is 6 digits. Incoming calls may contain 2 additional digits, which I then use to route the call to the correct extension. Telekom sends me all the digits. My problem is that when someone tries to dial an 8 digit number to an extension from an outside analog phone, AT sends the call

Hi, ? The current SCCP image on the 7942 phone is :SCCP42.9-0-2SR1S. We are trying to convert/upgrade the phone to SIP version of the firmware i.e : cmterm-7942_7962-sip.9-0-3 (Firmware is downloaded from the cisco support site). We have unzipped and placed all the files in the /tftp (root directory) of tftp server. Following files are also placed in the tftp directory. ? The Upgradation /

Before committing to about 50 of the spa942's, I like to take a last poll from those on the list to identify any negative issues that might be associated with the audio, functionality, early failures, etc, on the spa942. Expecting to deploy these using existing cat5 cabling and both rj45 jacks. Been using three of theme in a short term demo with the customer, but the demo systems has

Hi list, I'm having a problem with CallerID names not showing up when calls come in. I have dialplan code to store the callerid(name) away and it is blank (null). However, the voicemail variable ${VM_CALLERID} has the name field populated. For example, here is some of the dialplan code: 2. Set(CALLER_ID_INFO_ALL=${CALLERID(all)}) 3. Set(CALLER_ID_INFO_NAME=${CALLERID(name)}) 4.

Hello! Sorry for the OT-thread, but i don't know where else too ask... Has anyone done http-provisioning of a Linksys SPA942 with client side ssl-authentication? Where do i get the CA from? I'm aware of the Sipura mass deployment howto on voip-info.org, but it doesn't cover the authentification part. Thanks Christian

Am having a unique problem, calls received on my SPA942 seem to end after 15 seconds, but calls made from this device do not have this problem. For this device (when receiving calls) I get periodic "chan_sip.c set_destination: can't find address for host" I have set the "canreinvite=no" in the sip.conf. Does anyone have a sample entry from sip.conf for the Lynksys SPA 942

currently using 1.2.14 and zaptel 1.2.12 i'm using mfc/r2 so i can't move to 1.4 with sip jitter control and improved jitter control in zaptel 1.4. my problem is excessive jitter using linksys spa942. when i set canreinvite=no, which forces rtp to pass through *, quality is horrible. clicking sounds, pauses, etc. but when omitted or canreinvite=yes, sip to sip calls are ok. now, the

Fellow asterisk users, I am trying to get Single Line Appearance functionality working on a set of Linksys SPA942 phones and have not been successful. It looks like sla.conf is not getting read, only one phone reads as registered for the shared line, and a busy tone every time the shared extension is dialed. I have followed the documentation [1] and followed through other threads I saw

Hellos, I need to send personal directory from asterisk to the ersonal directory of the linksys spa 942. Is this possible? -- Best Regards, James Mutuku Ndeti Agile Systems Limited +254722490994 www.agile.co.ke mutuku.wordpress.com Has your organization implemented a customer relationship management (CRM)system? visit http://www.agile.co.ke/crm.php and find out how our CRM can help you achieve

Hi ALL, still having trouble getting Ast 12 to run. I got it compiled and built but now when I try to run, I'm getting a missing library error that seems to be in error (see below). The .so file DOES exist with correct permissions. [root at Asterisk12 ~]# asterisk -rvvv asterisk: error while loading shared libraries: libasteriskssl.so.1: cannot open shared object file: No such file or

I'm using a bunch of SPA942's, and I'm trying to provision them mostly by DHCP (and what I can't set that way, I try to provision via HTTP interface into the phone). I changed the domain in my AstLinux config from "astlinux" to redfish-solutions.com, and set that in my sip.conf file as well: context=incoming

Hello, I'm trying to build Asterisk12 on a Centos 6.4 VM. The configure script is erring out with: ? checking for uuid_generate_random in -luuid... no checking for uuid_generate_random in -le2fs-uuid... no checking for uuid_generate_random... no configure: error: *** uuid support not found (this typically means the uuid development package is missing) I have installed (using yum) uuid, uuidd

Hello all, I'm having a problem with my intercom function that I use for under-chin paging. I'm running 1.6.2.13 on this server, and we use Linksys SPA-942's for our general phones. I have a global defined which has all the SIP channels concatenated together - this is ${ALL-PAGE-EXTS}. The problem comes when a user is on the line, and someone else uses the intercom function to page