similar to: Disconnect supervision tone detection

Hi , Thanks danny nicholas. Finally we get the things done with following. If i specify busypatten=500,500 then asterisk does not recognize hang up signal. After removing it only all are working fine. I choosed 2nd option as per your suggestions. working chan-dahdi.conf: ==================== signalling = fxs_ks busycount = 3 busydetect = yes callprogress = yes progzone=in usecallerid=yes

I'm trying to use Asterisk as a voice mail system and all is going well except for one issue. When the outside caller drops the connection Asterisk doesn't sense it. It keeps the line open for about 2 minutes before dropping it. The FXO is attached to a key system (hybrid PBX). There was a home-type digital answering machine previously on the same extension and it was able to sense

Simple question that google hasn't helped much with (likely poor search terms) I just installed a Sangoma A200 with overall good results. Initial tests with both incoming and outgoing calls were very positive. Until I made a normal call that lasted more than 30 seconds. I setup the FXO with kewlstart signalling, and the outgoing call is never registered as 'Answered' and the dial

In AU we have a number of different dialtones defined for various purposes. >From indications.conf: au <ringcadance> 400,200,400,2000 au dial 413+438 au busy 425/375,0/375 au ring 413+438/400,0/200,413+438/400,0/2000 au congestion 425/375,0/375,420/375,0/375 au callwaiting 425/200,0/200,425/200,0/4400 au

> > > > I would be grateful if anybody could tell me what I should > > tell Verizon > > in NJ so they would enable "disconnect supervision" for my lines. > > > > Apparently "remote hangup notification" or "disconnect > supervision" or > > "calling party control" is NOT the magic phrase for them. Although >

Does anyone have disconnect supervision working on their TDM400P or X101P cards (to/from the telco)? Googling "telco disconnect supervision," I found the following description: http://mirror.lcs.mit.edu/telecom-archives/telecom-archives/TELECOM_Digest_Online/1559.html [cut] Re: How Do I Get "Kewlstart" From my Phone Company? Paul A Lee Tue, 24 Aug 2004 16:58:16 -0400 ... It

Hey all, anyone know the status of disconnect supervision on POTS lines in India? Set up an asterisk box, TDM cards, in Mumbai, and doesn't seem to have disconnect supervision...... Thanks -- Chris Earle System Solutions Specialist

I'm starting to shop for my first channel bank and one of the features that eveyone seems to recommend is "far end disconnect supervision". What other terms do various manufactures use to describe this same feature ? Is "calling party disconnect" the same as "far end disconnect supervision" ? Thanks

Hello list, Hope you all doing fine! I've tried to use the 'alias' directive in the indications.conf file but apparently it doesn't work.... It looks like maybe this feature was removed, because old sample for the indications.conf file have example using the alias parameter, but newer samples don't have it anymore.... also I couldn't find any ticket saying this parameter

I've the following setup : sip phone -> ser (auth and routing) -> asterisk with capi isdn when I call a pstn number everything works fine, but I can't hear anything till the called answer. this is the output from a test call : -- Executing Playtones("SIP/2.7.184.61-08152880", "dial") in new stack -- Executing Dial("SIP/2.7.184.61-08152880",

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress on we are having a few disconnects while calls are in session. I have talked both to some local phone contractors and SBC directly and

Hi I know this gets covered fairly regularly, but I've had a search through the archives and can't find anything dealing with this specifically - apologies if I've missed it though. I've got a TDM11B with the fxo port plugged into a standard UK BT PSTN line, loading wcfxs with OPERMODE=UK. All's working well, except if I get an incoming call through my bt line, and the

Hi all I'm using sangoma a200 cards in the UK and have the ongoing, often noted problem of disconnect supervision with BT POTS lines. Just noticed this post on http://www.voip-info.org/wiki/view/UK+Asterisk+Details stating that potentially someone's got a solution : "TDM400P &amp; Not Detecting Hangups: Got a TDM400P installed and having problems with Asterisk not detecting

I have an Audiocodes MP-118FXO in production. When an outbound call is made and the remote party hangs up, the Audiocodes hangs up the call immediately. But if an incoming call is received and the remote party hangs up, the Audiocodes does not hang up immediately. I have tinkered with Current Disconnect and Polarity Reversal settings, to no avail. Anyone experienced this issue with Audiocodes or

Hi, folks! Sangoma has an informal user survey up on their home page (at http://www.sangoma.com) asking if people would use their A500 card for North American BRI, if it were supported. I encourage anyone with an interest in voice BRI in North America to vote; this information will be used for deciding whether to make the investment in developing a National ISDN driver layer for it. Benefits to

The FXO lines on my TDM400 are connected to PSTN lines in Israel. As far as I know, the lines around here have disconnect supervision (I've seen some other Israelis on this list, anyone know for sure?), because it's worked on Dialogic cards, which reported hangup, not busy detect (while when I connect a Dialogic card to a PBX, I have to measure the busy signal's frequency/cadence or

Have a problem which can't find solution to on WIKI.. Trying to get * to use UK based indication tones. i.e. british ring, dial tone, busy signal. Have changed the indications.conf file to default to UK. However this seems to have no affect. What am i missing. Am using 1.0.3 stable. Many thanks Andrew. ---------------------- indications.conf [general] country=uk [uk] description =

Ok so this is officially driving me crazy. I have an Asterisk 1.6.1.6 install with DAHDI/DAHDI tools (latest) and an OpenVOX TDM400 card with 1 FXO port and 1 FXS port. I have a POTS line from my phone company attached to the POTS line. I have asked for "disconnect supervision" to be provisioned on my line and they claim to have added it. However, my scenario is as follows: I receive a

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress enabled in * we are having a few disconnects while calls are in session (about 2 reported in first 5 days of use). I have talked both to

Hi Vic, I hit that same problem! My SIP phones would sound okay when I made changes to indications.conf but incoming calls in to my TE410P had their own thing going on! Have a look at the zaptel source files, there's one called zonedata.c. You'll see the au settings... replace what's there with this: { 1, "au", "Australia", { 400, 200, 400, 2000 }, { {