similar to: Problems with Dahdi 2.3.0.1 trying to load OSLEC

I'm hoping someone can help me here. I've purchased replacement systems for 3 aging 1.4.x installs. I'm hoping to setup Asterisk 11, dahdi 2.6.1 and Oslec. I'm also moving those installs from Mandriva 10.0 to Debian 6.06 (Squeeze). In my testing, the TE220P PCIe cards that I have, the timing was awful on both slots, so I compiled Kernel 3.6.9 from kernel.org. Timing jumped to

Hi All, I have followed below steps to enable echo cancellation. # cd /usr/src # wget http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.28.tar.bz2 # tar xjf linux-2.6.28.tar.bz2 # tar zxvf dahdi-linux-2.1.0.4.tar.gz # ln -s /usr/src/dahdi-linux-2.1.0.4 /usr/src/dahdi # mkdir /usr/src/dahdi/drivers/staging # cp -fR /usr/src/linux-2.6.28/drivers/staging/echo /usr/src/dahdi/drivers/staging # sed -i

Hello oslec make error on RHEL 2.6.9 : Warning: could not find versions for .tmp_versions/dahdi.mod Warning: could not find versions for .tmp_versions/xpd_fxo.mod Warning: could not find versions for .tmp_versions/xpd_fxs.mod Warning: could not find versions for .tmp_versions/xpd_pri.mod Warning: could not find versions for .tmp_versions/xpp.mod Warning: could not find versions for

Does this make a significant improvement? The box in question I was going to try this with has a 4 port TDM card w/ plenty of horsepower, but I do intend to later migrate to a Soekris unit running Astlinux and therefore might not have the power to run it after. If the difference is significant, I may move to an ITX board so I could use a bigger CPU, but only if the hassle is worthwhile. Any

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.1 DAHDI-Linux 2.5.1 DAHDI-Tools 2.6.1 DAHDI-Tools 2.5.1 DAHDI-Linux-Complete 2.6.1+2.6.1 DAHDI-Linux-Complete 2.5.1+2.5.1 These releases are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.1 DAHDI-Linux 2.5.1 DAHDI-Tools 2.6.1 DAHDI-Tools 2.5.1 DAHDI-Linux-Complete 2.6.1+2.6.1 DAHDI-Linux-Complete 2.5.1+2.5.1 These releases are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools

Yesterday I pulled in the latest svn of Dahdi and added the files from a recent kernel in the drivers/staging/echo structure and modified the Kbuild file so it would compile without error. I insmod'ed the module in, and modified my system.conf has echocanceller=oslec. cat /proc/dahdi/1 shows: Span 1: WCTDM/0 "Wildcard TDM410P Board 1" (MASTER) IRQ misses: 1 1

Trying to build oslec. Following dahdi-linux README I copy drivers/staging/echo to dahdi-linux/drivers/staging. I uncomment the 2 oslec lines in drivers/dahdi/Kbuild. That doesn't work: /home/asterisk/build/dahdi/svn/dahdi-linux/drivers/dahdi/dahdi_echocan_oslec.c:33:35: error: ../staging/echo/oslec.h: No such file or directory So: wget

Hi list, I install dahdi-linux successfully with the module of oslec for the echo, but when I specify it in the system.conf the echo canceller oslec it shows me errors: DAHDI_ATTACH_ECHOCAN failed on channel 4: Invalid argument (22) I see that the echo cancellers is supported: mg2, kb1, sec2, and sec because oslec is not supported?, but he has support to compile it with dahdi_linux! best

Hi, I setup an asterisk system (asterisk 1.8-rc3, dahdi-linux-2.4.0 with dahdi-extra from Tzafrirs git, kernel 2.6.35.4). The hardware is an older pc system with Celeron CPU (2.5 GHz) with a Beronet BN4S0 ISDN card. The system starts without any errors. I discovered a severe issue. The kernel panics on a very small load. The first call normally gets through. If I start the second or third call

On Fedora 11, gcc-4.4, I'm trying to build oslec in dahdi-linux, but: [asterisk at asterisk dahdi-linux]$ make make -C drivers/dahdi/firmware firmware-loaders make[1]: Entering directory `/home/asterisk/build/dahdi/svn/dahdi-linux/drivers/dahdi/firmware' make[1]: Leaving directory `/home/asterisk/build/dahdi/svn/dahdi-linux/drivers/dahdi/firmware' make -C

On Thu, 22 Oct 2015 15:06:59 +0300 Tzafrir Cohen <tzafrir.cohen at xorcom.com> wrote: > On Wed, Oct 21, 2015 at 01:33:27PM -0200, Ethy H. Brito wrote: > > > > Hi > > > > Who should insert dahdi_echocan_oslec.ko module in Ubuntu 14.04? > > dahdi_echocan_oslec should be built by default. What you may miss is the > 'echo.ko' (OSLEC) kernel module.

Hi Who should insert dahdi_echocan_oslec.ko module in Ubuntu 14.04? dahdi start/stop service? I have a test installation that is not launching it when asterisk/dahdi starts. Clues? Regards Ethy

Hi List. I've bought a new server for my home asterisk installation and I'm trying to install asterisk with dahdi drivers and OSLEC. To do that I've got the svn dahdi-linux trunk revision 5366 and the echo subproject from the 2.6.28-rc6 Linux kernel sources. As reported in the dadhi README file I've uncommented out the two OSLEC related lines at Kbuild file in the

Hi, I've a problem: I can't configure DAHDI with ech canceller OSLEC. I have Asterisk 1.4.24 and DAHDI 2.1.0.2. I compiled also OSLEC. But when in /etc/dahdi/systems.conf I insert value echocanceller=oslec,1-4, command dahdi_cfg -vvvvvvvvvvvv give me an error about oslec. Someone can help me? Thanks Marco -------------- next part -------------- An HTML attachment was scrubbed... URL:

In order solve my incoming caller ID problem, I upgrade the dahdi to version 2.6.1 from version 2.4.x. After upgrade, I found the echo cancellation doesn't working (I'm using Digium AEX800B PCI Express card). I can hear my self talking on the phone. How to solve this? I think I need to recompile dahdi 2.6.1 with OSLEC support? how? [root at callcenter ~]# dahdi_cfg -vvv DAHDI Tools

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

I wonder if anyone has any ideas on this. I have recently migrated my server from a custom built Linux with Asterisk, Zaptel and Oslec running fine, to Ubuntu Server 8.10. I have Asterisk installed via synaptic at it works fine. I have built and installed the zaptel package by doing the following commands: sudo m-a -t build zaptel cd /usr/src sudo dpkg -i zaptel-modules-{version}.deb sudo

Hi All, Which echo cancellation is good between OSLEC and MG2. Dahdi by default use MG2 echo cancellation on channel. If i want to use OSLEC then what should i need to do ? Do i need to recompile dahdi with OSLEC ? -S -------------- next part -------------- An HTML attachment was scrubbed... URL: