similar to: CallWaiting

I am wondering if anyone could help me figure out how to turn down the volume on all the dial tones, indications, etc.. and especially the call-waiting CHIRP! I don't want to change the txgain and rxgain because they are working at levels that I would like. However, when voice conversations and voicemail recordings are at good levels then the dial tones, busy tones, etc are way too loud.

Hey all...I can't seem to figure out *exactly* what needs to be done when I can't flash over to an incoming callwaiting call on FXO from an FXS card. Right now if I get a callwaiting call from the FXO and hit flash nothing happens. I've been over the archives and google and it appears that this is possible and I guess it can be done with *0 but I haven't found the config on

The problem: T100P connected to an Adit600. Channel 1-16 are FXS, 17-24 FXO. I have Zap/24 in callgroup 3 and Zap/1-16 in pickupgroup 3. When a call comes in on Zap/24 I cannot pick it up with *8 from Zap/1-16. *CLI> show version Asterisk CVS-04/27/04-23:48:08 built by root@tuck on a i686 running Linux The zapata.conf and extensions.conf are located here:

Hi, I have problem with X100P clone card.I can not force it to work under Asterisk 1.4.27.1 and DAHDI Version: 2.2.0.2. I looked over and over on configuration and could not see any mistakes. Here are relevant configuration files. /etc/dahdi/system.conf > fxsks=1 > echocanceller=mg2,1 > loadzone = hu > defaultzone = hu > dahdi_tool > OK Wildcard X100P

Hi, I facing a problem with flash hook. When ever I do a flash hook to place an extsing call on hold, the call gets disconnected. The debugs on Asterisk shows that 'on hook event detected' when I press the flash button on the phone. The setup is like this Asterisk box with T1 cards and FXS cards. The T1 card is connected to an IAD and configured for ISDN PRI lines. Analog phones come

Hello, I have a system with two cards: a HFC-PCI ISDN and a TDM21B (2 FXO and 1 FXS), running Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1l with freePBX beta5 dialplan. I have connected an analog phone to TDM FXS port, but when I pickup the phone to make a call, Asterisk "hangs up" the call. Let me explain: In another system, when I pickup the phone, Asterisk give me tone to dial: >---

Can anyone suggest where I might begin looking for an answer please? I have just installed a TDM400P (2x FXS and 1x FXO modules installed) The first problem is that it does not seem to be able to detect if the remote party has hung up when a call comes through on the FXO. For example, if someone calls in, and then hangs up at any time after it starts ringing, Asterisk carries on as though the

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

I've been having trouble with making outbound calls to my TELCO from a TDM400 card (FXS KS signalling) after upgrading from 1.6-beta9 to 1.6.0. The problem is completely intermittent. When it fails, I get this message: [Nov 9 19:12:26] WARNING[18916] app_dial.c: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) At some point, it starts working, but I don't know what

We have an asterisk box with the following configuration: - AMD Athlon XP 2400+ - 512 MB RAM - SUSE Linux 10.1 - a Digium card TDM400P with 3 FXO - another Digium card TDM400P with 4 FXS - asterisk 1.2.7.1 - zaptel 1.2.4 I already checked that those cards aren't sharing interrupts (by cat /proc/interrupts): 0: 14119786 XT-PIC timer 1: 10 XT-PIC i8042 2:

-------------------------------------------------------------------------------------------- Originally posted at http://forums.digium.com/viewtopic.php?t=18045 -------------------------------------------------------------------------------------------- Hi! I'm trying to configure a DISA setup (Asterisk 1.4.11). Only, executing DISA seems to prevent any DTMF detection capability when using

Hello, my configuration is the following: a TDM400P board with an fxs and fxo daughter boards on it. I thus connect a fax to my FXS port, after having verified that this port was correctly functioning. For this, I had tried before with a simple phone, and with some basic voicemail exten scripts. Here is my simple dialplan for my fax reception: exten => 300,1,Ringing() exten =>

Hi all, I must admit that I am stuck. I have a TDM400P card with two FXS and two FXO modules which I had set up and configured so that it was working beautifully. The only problem was that occasionally it would get itself into a state where outgoing calls would simply be met with a very loud static. A reboot would fix this issue and everything would work fine for a while. Recently however,

Hi, Some calls I make trough my PSTN asterisk gateway just hangup after some minutes. Even if I'm using sip or iax. I have callprogress=no busydetect=no in my zapata.conf. Anyone help? Or tell me what to look at /var/log/asterisk/debug. I didn't find anything wrong. [endpoint]---iax or sip----[asterisk]----E&M----PSTN. As endpoint I had tested another asterisk box (with a FXS),

So, tweaking configs, rebuilding this and that... restarting, twiddling, it works (yeah!), but fails on re-boot to work at all. Consistently, though. I believe it comes down to this: I can call out only *after* I've received a call. So, cold boot. Then: modprobe dahdi modprobe wctc4xxp modprobe wcfxo dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.1.0.3

Hi, We are having a problem with asterisk detecting that an analog ext has been put down. This seems only to happen after a number of calls have been made. We have an FXO port (TDM400P with FXO module) connected to our PBX and are using this to test asterisk prior to rolling our for our small office. What happens is that we make a number of calls to this ext which 1st rings a phone (FXS)

Hello, I have a strange problem with one of my Zap channels. A user told me that he was in a voicemail system during a call, hit the Flash button, and the call hung up. Now we get no dialtone on the phone hooked up to the channel. Here's the status of the channel: jmartin at rogue:~$ sudo asterisk -r -x "zap show channel 7" Parsing /etc/asterisk/extconfig.conf Channel: 7 File

I've been monitoring this problem for almost a month now. I realized that it is more extensive than what I described previously. I can very easily replicate this problem on every Zap channel. Following is the senario: 1. Call Zap/5 via say SIP/15 -> Zap/5-1 created and starts to ring 2. Call Zap/5 via say SIP/21 -> Zap/5-2 created and starts to ring 3. Hangup SIP/15 ->

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,

Hi, I have 6 Red FXO with TDM2400p in my PC. I have install asterisk and dahdi driver. Scenario is jitsi-----> asterisk server-----> analog PBX ----> landline phone I configured this scenario as follow in chan_dahdi.conf file ; General options [channels] usecallerid=yes hidecallerid=no callwaiting=yes threewaycalling=yes transfer=yes