similar to: Conflict between jumper settings and dmesg with OctoBRI

Hi, Looking at dmesg, I can see : [ 45.213205] wcb4xxp 0000:01:07.0: Span 5 has invalid sync priority (5), removing from sync source list [ 45.213205] wcb4xxp 0000:01:07.0: Span 6 has invalid sync priority (6), removing from sync source list [ 45.213205] wcb4xxp 0000:01:07.0: Span 7 has invalid sync priority (7), removing from sync source list [ 45.213205] wcb4xxp 0000:01:07.0: Span 8 has

Hi, a few month ago, I tried to install zaptel for my Beronet BN8S0 pci card... I gave up and took hfcmulti/lcr. Now dahdi (2.2.1.1) seems to support the card and I'm very interested to get it to work. But how to get rid of these annoying qozap driver? bishop dahdi # lspci -v -nn -s 01:00.0 01:00.0 ISDN controller [0204]: Cologne Chip Designs GmbH ISDN network Controller [HFC-8S]

Hello, I've got a running system in which logs are full of messages such as: [Jun 10 07:24:14] NOTICE[2414] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 The strange thing is those messages are coming from a single span. My setup is : Asterisk 1.6.1.18 Junghanns OctoBRI with wcb4xxp driver libpri 1.4.10.2 dahdi 2.3.0 3 BRI lines in PtMP mode What does this

Hi, I'll soon replace a Junghanns OctoBRI with a Junghanns QuadBRI. As both use wcb4xxp driver (dahdi 2.3.0, libpri 1.4.10.2 and asterisk 1.6.1), I'm planning to proceed this way : 1. Edit 2 versions of files /etc/dahdi/system.conf and /etc/asterisk/dahdi-channels.conf (one for each card). 2. Link current system.conf and dahdi-channels.conf to QuadBRI files. 3. Power PC off 4. Swap cards

Hi, Using Xorcom's bristuff-0.4.0-RC4-xr7.tar.gz (ie asterisk 1.4.25) with an old Junghanns OctoBRI (ie not the 2.0 version), zttool shows every port in TE mode, though half of them are in NT. Alarm column shows OK for every port, such as : OK octoBRI PCI ISDN Card 1 Span 1 [TE] Lay Globally, this system doesn't work (can't dial out through zaptel) Replacing this board

Hi, I mistakenly posted this to Dev list.... I wonder if I use quadbri or octobri cards to insert Asterisk between ISDN PBX and ISDN line - if power of Asterisks fails - will those card connect PBX directly to ISDN line ? If not are there any other simple switching devices, that would do this (in power fail it will connect ISDN PBX to ISDN lines directly) ? Thanks in advance, regards, Rob.

Hi, When typing dahdi_scan on an OctoBRI-enabled setup, I've got only 8 replies such as : [1] active=yes alarms=RED ... [8] active=yes ... framing=CCS I would expect 16 replies (one per B-channel). Is this correct ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |

BUG/SYMPTOMS: 1.Under certain circumstances, octoBRI (and most likely quadBRI) ISDN cards (Junghanns/CologneChip) severely distort certain ISDN payload. 2.Although these claims relate to the bristuff patch, the problem might not be limited to bristuff and in fact be rather asterisk/zaptel/libpri related. 3.Signal distortion is limited to the use of the CVS version of the Bristuff patch for

Hi all, I just posted this question before last week. Meanwhile after upgrading Asterisk 1.0.7-BRIstuffed-0.2.0-RCg to 1.0.8-BRIstuffed-0.2.0-RCh the same problem occurs, but seems to be more seldom. Attached is now the output of "zap show channel" . - I'm running a stable Asterisk on a HP DL380G2 1.4Ghz 0,5GB RAM equipped with 1x TE410P and 2xJunghanns OctoBRI running in NT-mode.

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

Hi, On my system I've got : CLI> dahdi show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO B4XXP (PCI) Card 0 Span 1 OK 0 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) B4XXP (PCI) Card 0 Span 2 OK 0 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) B4XXP (PCI)

Hi, I did replace an old asterisk box by a new shiny one (2 BRI ports used on a quad port card - BeroNet PCI Express) I noticed a message in the logs that puzzles me: May 11 19:10:02 kernel: dahdi: Master changed to B4/0/1 May 11 19:10:08 kernel: wcb4xxp 0000:05:04.0: PCI INT A disabled May 11 19:10:08 kernel: wcb4xxp 0000:05:04.0: Driver unloaded. May 11 19:10:08 kernel: dahdi: Telephony

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment***************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ****************************************************************** In my case , I set prot 1 and

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Dear Supports, I was attempting to install BRI Card(OpenVox B800P) with wcb4xxp in NT mode .But I can not make it worked! Could you please give me some hints? Thanks in advance! Here are my environments: ------------------------------ CentOS-5.3 Kernel-2.6.18-164.el5 asterisk-1.6.1.6 dahdi-linux-complete-2.3.0+2.3.0 libpri-1.4.10.2 OpenVox-B800P(the first port is spliting into

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment********************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ******************************************************************** In my case , I set prot 1

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.11.0-rc1 DAHDI-Tools-v2.11.0-rc1 dahdi-linux-complete-2.11.0-rc1+2.11.0-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete * This release

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.11.0-rc1 DAHDI-Tools-v2.11.0-rc1 dahdi-linux-complete-2.11.0-rc1+2.11.0-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete * This release

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.11.0 DAHDI-Tools-v2.11.0 dahdi-linux-complete-2.11.0+2.11.0 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete * This release adds automake