similar to: HDLC Receiver overrun on Wildcard TE410P

hi folks. recently some of our customers complained about bad voice quality on the phone system. i looked at the logs and found a lot of these: [2012-11-03 08:26:38] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:45] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:54] NOTICE[11305]

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

Dear members of the list, I have difficulties to obtain sync with a Digium TE420 PCI Express For four entries E1, In my case I am with only 3 E1s available to configure. The telephony operator is BrasilTelecom and Signaling is R2 Digital. The information I have is that are E1s with 32 channels, not have sure. My settings Have been based on the link reference:

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

We are using AAH with Asterisk 1.2.7.1 with a TE405P as listed below. We are getting frequent restarts on the spans which lead to dropped calls. I have pasted some hopefully pertinent information below -- anyone have any clues that might help? Thanks Next line is repeated throughout messages, going through every channel in every connected span. asterisk/full.1:Apr 24 01:15:25 VERBOSE[4196]

Hi All, I am facing problem with E1 line. I have installed Asterisk (1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10) But every now and then I face problem of down E1's. The log show lot of entries like "pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2" This happens on a regular basis and the E1 becomes up after some time. My

Hi anyone have a idea for debug my digium TE405P card ? My zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone = fr defaultzone = fr My Zapata.conf: [channels] language=fr context=from-E1 switchtype = euroisdn pridialplan = unknown signalling = pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

I just managed to put in a TE410 card in an Asterisk box to work with OnRamp 20(E1 downunder). I am able to dial in but was not able to dial out. Can anyone offer me some advice please? In my extensions.conf, I just put in: [default] ... exten => 0,1,Dial(Zap/g1) and I get this on the console when I dialled 0. -- Executing [0 at default:1] Dial("SIP/5166-b76004f8",

hello list, i have installed 2 diguim cards in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

Hello- After configuring DAHDI and starting asterisk, I get the following message continuously on the Asterisk console: WARNING[2057]: chan_dahdi.c:4158 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! My card is a D410P configured for E1, only the first span is configured, and configuration snippets are as follows: From /etc/dahdi/system.conf:

Hi, Running 1.4.26.1 here. I have installed TE420B card in my server, and followed the appropriate steps (as far as I know to configure it). This TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling type. When I dial out, I get this message: Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0

Hi, I'm running an 8E1 setup to an SS7 carrier. The setup works but when we start hitting the 80 active calls mark the link became unstable. I found a lot of the following messages afecting my d channel Jun 25 15:49:55 ostional kernel: [385661.368857] dahdi: HDLC Receiver overrun on channel TE4/0/1/31 (master=TE4/0/1/31) Im using TE410P dahdi-linux-2.4.1.2.tar.gz dahdi-tools-2.4.1.tar.gz

I have a 'CONGESTION' Status with R2 protocol. While testing this scenario sip GW--?Asterisk ?Digium E1 R2 Protocol?Cisco E1 R2 protocol?sip Gw Find below my error and configuration ,where are the errors in my configuration ? ========================================================================= Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on

Dear All, we have installed a TE410P card on a Dell Poweredge 1750 running a slackware 10 with 2.4.26 Kernel. Then we have made two loops on the card and we have configurated all the 120 channels. Our goals was to perform some stess tests even if in this scenario we used the same box as generator and target. The stress test comprised to generate up to 60 calls at the same time by placing a file

I have a pair of sites tied together with a T1 line running zaptel PPP on either end. The system works, but I keep getting these messages in the kernel logs, and users are reporting connection problems (TCP timeouts, and hangs) especially under high usage. --snip-- HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC

Dear, I always had one E1 card with one span, so I've never had any problem in set it up through /etc/dahdi/sustem.conf and /etc/asterisk/chan_dahdi.conf because I put span=1. But now I have a PBX with two E1 cards with 4 span (8 span in total). How do I have to define both card in system.conf and chan_dahdi.conf, and how do I have to refer each span to the corresponding card ??? Thanks a

Anyone else seen this eth-device and what brings it up? [root at oh1mrr etc]# ifconfig __tmp1192348344 Link encap:Ethernet HWaddr 52:54:AB:DD:2E:D1 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2094689 errors:0 dropped:0 overruns:0 frame:0 TX packets:1645734 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX

Hi, I'm trying to bring up two PRIs from qwest with asterisk and dahdi. I'm using an OpenVox D410E and the drivers are loaded. My system.conf looks like this: # Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" B8ZS/ESF RED span=1,2,0,esf,b8zs bchan=1-24 # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" (MASTER) B8ZS/ESF RED span=2,1,0,esf,b8zs bchan=25-47 dchan=48 These

Hi, after loading the zaptel driver wct4xxp I have strange log lines in the syslog: Out of storage space. free tells, that more than 900 MB are still free. Disk space is also available. I'm using a dual opteron in 64 bit mode. Any ideas? Roger. Syslog: Dec 1 02:18:37 ipphone4 kernel: TE410P: Launching card: 0 Dec 1 02:18:37 ipphone4 kernel: TE410P: Setting up global serial

Hi, I have a digium card (igium, Inc. Wildcard TE405P quad-span T1/E1/J1 card 5.0V (rev 02)) 4 ports I want to make a loop test between digium card E1 to test the configuration of dahdi What I want to do scenario is I connect port 1 and port4 in the digium card with E1 cable SIPcall-->E1 Digium port 1--->(Loop)E1 port 2---->sip extension local. kindly can any can help me to