similar to: shared lines (sla) with Asterisk 1.4.26, any hints?

Fellow asterisk users, I am trying to get Single Line Appearance functionality working on a set of Linksys SPA942 phones and have not been successful. It looks like sla.conf is not getting read, only one phone reads as registered for the shared line, and a busy tone every time the shared extension is dialed. I have followed the documentation [1] and followed through other threads I saw

Hi All. I've been experimenting with SLA on Asterisk 1.4.13 (patched up to 1.4.14). I am using a SIP channel for my "trunk" line. On the whole things are good, but I have noticed that if I misdial an outgoing call, i.e. I get 404 "Not Found" in the SIP trace, then the trunk line just drops, rather than presenting an error tone or message to the user.

On 8/7/07, raviprakash sunkara <sunkara.raviprakash.feb14 at gmail.com> wrote: > > Hello Russell, > Nice To meet U and Good Morning. I got u r mail-Id from > http://www.asterisk.org/node/48325 > Recently i started the SLA configuration. But i didn't understand the > Flow of its Functionality > One of the My Client Ask to have do deploySLA feature > He Using

Has anyone had any success with getting SLA going between 2 SIP phones? (Particularly a set of Cisco 79xx's) The SLA document that comes with the asterisk source is about as clear as mud. Does anyone have a working sip.conf, sla.conf, and extensions.conf that I can use for reference? The part I'm most confused about is how to build the lines in sip.conf and how the phones should

I currently have 4 lines coming into the house. We currently have an Avaya standard analog key system which has served us well, but running extensions is a major pain and requires a dedicated run per extension. I have ethernet run throughout the house though. The first two lines are "home" lines, however line1 I use for my consulting during the day, and line2 is used by my wife for

I configured my sla.conf to use with a Polycom phone. I have no idea if I did it right, however, none of the console "sla" commands exist. Do I have to something special to compile in this support, or should it just work out of the box? ~jay

Hi all, I need to connect my Asterisk 1.4.26 with a Sangoma PRI card (configures with signalling=pri_net)) to a Cisco 2800 PBX. After connecting the cables everything seems fine (ifconfig w2g1 is ok, wanpipemonitor gives no errros, the span is up and active, green light on the card) but when I make a test with my iax phone, there's no way to dial the PBX and I get this WARNING: [Jul 2

Greetings, Back in September someone asked about documentation for the new SLA feature in 1.4, however they received no replies. I thought I might ask the same question now in December. Apart from sla.conf.sample and a few comments in app_meetme.c I have been unable to find useful documentation. Is anyone using this feature right now? Is there a helpful source for information this highly

I understand that the Asterisk SLA implementation is somewhat different from most key systems and PBX systems. I also understand that in Asterisk, one does not put an SLA line on hold since it is just a MeetMe conference. However, is there any way to make the BLF flash when the answering party on the Asterisk system presses the hold key on their set and leaves the calling party alone in the

Hello, Information: gcc -v: gcc version 4.3.3 (Debian 4.3.3-3) os: Debian/Testing Pulled latest release from asterisk site, compiled, installed it. I have a barebones configuration: $ ls -l asterisk extensions.conf modules.conf sip.conf users.conf voicemail.conf You can see them here: http://home.comcast.net/~jpiszcz/20090418/extensions.conf

Has anyone done SLA with Polycom phones? I've got a large project coming up where the customer is keen on SLA for trunks and extensions. Trunks will be on a PRI. We may do this with Cisco phones if they work better. Mark Willis

Hi. I've been researching very deep into SLA in Asterisk 1.4, and am unclear as to if the feature exist. I know the commands and configs are available, but there is no documentation, and I've heard that it will not be supported until 1.4.1. Does anyone have a definitive answer on this? If it is available, is there any documentation on the feature? -Chris

I have read that 1.4 has shared line appearances, which I assume will work with Polycom phones. Has anyone configured this and verified it working? I was going to start playing around with it but wanted to see if anyone else has tackled it yet. Bill -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, I am looking for a "real life" example of using SLA lines under Asterisk. I'll describe my environment and would like to know how I define it in Asterisk (version 1.4 final). Suppose I have two multi lines phones. The first phone has extension 1 assigned to it, and the second phone has extension 2 assigned to it. Now, I want extension 3 to be available on both phones as

Has anyone successfully gotten the features of sla.conf to work with Polycom phones? I would like to get 501's to show 3 shared lines on each of the keys. Particularly I am looking for a sample configuration for the phone, the Asterisk configuration seems simple enough. I've searched and searched and searched and have not found anything, general info about SLA yes, but nothing specific

Hello, every body Anyone set up, the sla sharing line appearances, in asterisk, I'm setting, tha but, don't, work, I change the sla.conf, extensions.conf, and sip.cfg, but don't work fine. Any one, could setup, tha? Regards Carlos Rojas -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm trying to record all calls including calls that are part of a SLA. Using both monitor and mixmonitor the recording appears to happen (that is, asterisk logging shows it happening) however the file is never written to. It doesn't seem to be possible to use the recording that is part of the meetme app because when the SLA app creates the conference it passes NULL in the options field

Anyone have an example of using SLA with SIP handsets in Asterisk 1.6? I'm looking at the sla.tex file and wondering when it was last updated... Thanks, -Philip

Hello, do you know if it is possible to define the SLA configuration in the database for realtime usage with asterisk? Leandro -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20141114/7c4f09a4/attachment.html>

Hi all, i'm trying from several days to setup a SLA on my machine with some THOMSON 2030. My goal is to bind every F key to an extension (NOT a trunk). So, F1 = 201, F2 = 202, F3 = 203, and so on... I'm googled thousand of pages and many more confusing concepts are in my mind. My server uses extensions with numbering 2XX placed in context 'phones'. I set yet in sip.conf: