similar to: G.729 Codec problem.

Hi, I am trying to post this again as I am getting no answers and the support@digium.com bounces... (I have searched the whole list and can't find the answer either) I have installed a 5 user license for G.729 and want to route calls through Asterisk from my G.729 phone to Cisco AS5300 also using G729. Both Cisco and the phone connect using this codec if I do not force the call to go

Hi Sir, We have integrated Skype with Asterisk (skype user id:- rexesbposolutions). Each call which is coming to skype account is getting transfered to Asterisk Queue. It has following two cases: case 1: When we call from normal skype account to skype account (rexesbposolutions), everything is working fine. case 2: This skype account (rexesbposolutions) has been assigned with a online virtual

List, I purchased 2 g729 licenses but I can't get it to answer a g729 call from a cisco router with a vwic card. In the debug output below you will see that asterisk thinks it only supports: (gsm|ulaw|alaw|h263) when it should support g729 according to the config also listed below. The real odd thing is I can place g729 calls to the router, just not from the router to *. Anyone have any

I'm trying to use the Digium suplied G.729 Codec, I have ran the register utility, and got my licenses written to /var/lib/asterisk/licenses, but when a start Asterisk I got the following errors: [Mar 24 12:33:08] NOTICE[4068] codec_g729a.c: G.729 transcoding module version 34, Copyright (C) 1999-2007 Digium, Inc. [Mar 24 12:33:08] NOTICE[4068] codec_g729a.c: This module is supplied under a

Firstly, I'm running Asterisk 1.4.4 on Solaris 10. I have several different internal SIP phones all sharing a single IAX2 VoIP channel. PHONES |------------- <SIP/uLAW> --------------| ASTERISK |-------------- <IAX2/g729> ------------|VoIP/ISP The g729 codec has been registered successfully and appears to be detected by Asterisk (NOTE: I have changed what I thought might have

Hi, I have licensed the digium G.729A codec. But for some reason incoming and outgoing calls will ALWAYS use G.711a. When I force my phone to only accept G.729 then an incoming call from ZAP goes straight to my voicemailbox as the phone doesn't accept the codec Asterisk wants, even if I force it in sip.conf. Is there anywhere else I need to look to tell ZAP to use G.729 preferrably ? The

Hi, I am trying to replace my Cisco 5300 gateway with my new Zap TE405P card. Incoming calls and outgoing calls between my cisco and my SIP phone works fine on G.729. Recording messages in the asterisk voice-mailbox also works fine from both my SIP phone as well as PSTN -> Cisco -> Asterisk. I have licensed the digium G.729A codec. When I connect my ISDN PRI to my Zap card and I call

Hi, I've been trying to get the G.729a beta codec running with my remote Asterisk box that talks IAX2 to my local Asterisk box. Digium fixed the problem I was having in registering the beta codec, so that now works fine. I've removed the old codec_g729b.so from /usr/lib/asterisk/modules and put in place the codec_g729a.so beta from digium FTP. My CVS build of Asterisk is about a

Hi, I carefully followed instructions in README file lasting with : /root/register ... blabla asterisk -r CLI> restart now Then asterisk -r fails with : # asterisk -r Asterisk 1.6.1-beta4, Copyright (C) 1999 - 2008 Digium, Inc. and others. Created by Mark Spencer <markster at digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for details. This is

I upgraded my server from Fedora Core 4 to Fedora Core 5. I was wondering if anybody else has run into the problem and know's the fix? I recompiled asterisk and if I don't have the /usr/lib/asterisk/modules/codec_g729a.so file in place it works. I use or used to use the licensed G729 Codec from Digium. This is the error message from asterisk -vvg: [app_playback.so] => (Sound File

Hi, I have a Cisco 5300 which I want to make a call THROUGH the Asterisk PBX (security) to an IP phone which supports g729, and vice versa. Both Cisco and the phone talk this codec if I do not force the call to go through * However if I say canreinvite=no in the sip.conf for either of these gadgets, the call will fail with No compatible codecs! I have bought a 5 user license just to

Hi folks, In an effort to save bandwidth (our 7905s run over a WAN) we've switched from ulaw to g729a. We purchased 4 licenses from Digium (4 SIP clients, low call volume), and they seem to have been accepted: [codec_g729a.so] => (Annex A/B (floating point) G.729/PCM16 Codec Translator) == G.729 Host-ID: 07:53:aa:d3:e2:f2:bd:cc:27:60:9d:5f:da:eb:5d:e9:6e:09:a1:4e == Found license

Hello Everybody, Since I upgraded to 1.4 I always get the difficulties as below, which I have never had in 1.2: [Dec 28 21:05:59] VERBOSE[1734] logger.c: -- Call accepted by 202.153.128.34 (format g729) [Dec 28 21:05:59] VERBOSE[1734] logger.c: -- Format for call is g729 [Dec 28 21:06:00] VERBOSE[1756] logger.c: -- IAX2/VoIPRakyat-2 is ringing [Dec 28 21:06:00] DEBUG[1756]

Hello Everyone, I've successfully registered my g729a licenses. When i try to load the module from asterisk Cli i got the following error *Error loading module 'codec_g729a.so': /usr/lib/asterisk/modules/codec_g729a.so: cannot restore segment prot after reloc: Permission denied* * loader.c:795 load_resource: Module 'codec_g729a.so' could not be

Hi List, it feels silly, but here I am. My Asterisk box is useless, after running a long delayed yum update (Centos box). ***** A few details on the box: cat /etc/redhat-release CentOS release 5.10 (Final) arch i686 uname -a Linux hermes 2.6.18-371.4.1.el5 #1 SMP Thu Jan 30 06:09:24 EST 2014 i686 athlon i386 GNU/Linux asterisk -r Asterisk 1.6.2.20, Copyright (C) 1999 - 2010 Digium,

Hello, I wonder if anyone else has noticed this. I see a pair of calls to pipe() within the codec_g729a, and suddenly, I have a leaked file descriptor that remains until asterisk dies. Now, maybe no-one sees this, mainly because I have no g729 licenses on the machines where this happens. And conversely, I haven't yet studied servers that do have licenses. Why have codec_g729a.so loaded if

Recently with Asterisk 1.4.17 I've been running into some stability issues. I started looking through my logs, and I found this: [Jan 29 09:41:45] WARNING[13132]: loader.c:620 inspect_module: Module 'codec_g729a.so' was not compiled against a recent version of Asterisk and may cause instability. I'm using the newest version of codec_g729a.so from the Digium website (v33).

Greetings- Was running the Digium FreeBSD g.729 codec until recently when the latest Asterisk bits were obtained via svn: svn checkout http://svn.digium.com/svn/asterisk/trunk asterisk This produced: Checked out revision 30652 This on FreeBSD 6.1-RELEASE Attempting to start asterisk it returns: == Registered custom function URIENCODE [codec_g729a.so]May 27 13:29:59 WARNING[71884]:

Hello, I have VPC (Voice Pulse Connect) and NuFone for providers and I have setup modules.conf with the registered (Digium) G.729 Codec such as: load => codec_g729a.so load => res_crypto.so With both sip/iax2 configuration disallow=all is first and then allow=g729 is next (allow=ulaw,allow=alaw,allow=gsm are next after allow=g729) and it always dials via ulaw. Why is this happening? Josh

I have a fresh 1.4.10.1 installation that appears to have a problem with g729 pass-through. I can see the gateway in question sending an INVITE using g729b. However, the Asterisk is only sending g711 in the INVITE to my Polycom phone. [gateway] disallow=all allow=g729 [phone] disallow=all allow=ulaw allow=alaw allow=g729 There's the codec configs for the gateway and the phone in question.