similar to: SIP Disconnects from Network - Asterisk Does not hangup

We have had 20 calls over the last month where the SIP channel has not identified that the person on the receiving end has hung up. Is there a way of fixing this ? TIA Julian

Hello, For the moment I have the following settings in my sip.conf. I want to optimize them to archive the following things: - for the moment all my users will re-register too often. I want that only lagged users to re-register quickly. - check from time to time all users but no too often to see if is logged and can be called. Overall i want only lagged users to reregister and users with good

I have a problem with calls not hanging up if for some reason the physical phone dies or gets unplugged I can demonstrate this in practice by making a call from a handset, then unplugging the handset from the power. The call remains active and asterisk never seems to disconnect it. More annoyingly when power is re-applied the handset comes back to life, won't receive incoming calls

Hi,

Dears; I am facing a problem in disconnecting the calls, it is related to the rtptimeout (disconnecting if there is no RTP packets from both sides). My Asterisk Box is behind NAT but there is a static real IP address at the ADSL router. We call from the Mobile to the PSTN analogue numbers which are connected to Asterisk Analogue card (the telephone lines are analoge), and then we dial the

Hi, Anyone here using sipgate.de ? It worked for months, but for a couple of days now I'm unable to register with them. My account is ok, because I can login to the website. Asterisk keeps showing me: Feb 25 23:50:18 NOTICE[5144]: chan_sip.c:5269 sip_reg_timeout: -- Registration for 'XXXXX@sipgate.de' timed out, trying again (Attempt #n) I looked at the sip debug stuff, and all I

Hi, I am not sure if I am doing something wrong, but I can't get MeetMe to work with GSM codec (Asterisk 1.6.1 SVN r190371). My config files below: ---- sip.conf: ---- [general] context=common canreinvite=no bindport=5060 bindaddr=78.105.1.127 disallow=all allow=alaw allow=gsm rtptimeout=600 rtpholdtimeout=3600 rtpkeepalive=30 nat=no jbenable=yes tcpenable=no realm=dev-sip.wima.co.uk

It seems that when setting qualify = 200 or qualify = yes in the database for a sip friend/peer, RealTime does not update the registration status like it should. I also have several peers which have been offline and Asterisk still reports them as registered, even though the registration seconds are only 200. Asterisk Ver: CVS HEAD 12/1/2004 Layout of sip_buddies: mysql> describe

Hi, Red Hat 9.0 Asterisk 1.2.7.1 Whenever I start Asterisk, I am unable to call out on my SIP channel: >-- Executing Dial("Zap/1-1", "SIP/6137451576@6477235412||t|") in new stack >Apr 30 11:02:00 WARNING[12814]: chan_sip.c:1973 create_addr: No such host: 6477235412 >Apr 30 11:02:01 NOTICE[12814]: app_dial.c:1029 dial_exec_full: Unable to create >channel of type

Hi All Total noob on the list so all help appreciated.... I've successfully installed Asterisk on an IBM A30P Thinkpad using fedora Core 2 (I'm looking at having a mobile PBX for conferences and shows). I've plugged in two Cisco 7960 phones.... The phones register with the Asterisk correctly and I can run the demo's and even the AIX demo through to digium works correctly.......

Does the System() dialplan application have a limit on how long it can run? Either a time limit, or server load limit? I'm trying to pipe the output of Sphinx2 into Text2Wave, but Asterisk just runs by it to the next extension priority, with no errors. If I run the same command via the system shell, all is good, though it does take a few seconds, probably about 5 seconds to run. Yes,

There is one question about re-Invite. Is it possible to carry out operation corresponding to draft-ietf-sip-session-timer -14? Ichiro Nakata i-nakata@nttpc.co.jp

I have a couple asterisk boxes, running sip between both boxes. 1.4.43 on both. both are installed from source, both have default settings, My config for one box is: [devgeis] type=friend defaultname=devgeis username=devgeis secret=yes disallow=all allow=ulaw allow=alaw allow=gsm rtptimeout=60 rtpholdtimeout=60 rtpkeepalive=60 host=192.168.1.8 context=panel The other box is the same. There

Hi all! This is my VoIP network scheme H323EndPoint ----- --- GW H323/SIP-IN -- -- SIP Phone | | (Sipquest) | | | | | |

Hello - I currently have 10 DID's coming into one Asterisk server, I seem to be having some difficulty routing based on the DID dialed and am hoping someone on the list can assist me. Here's the relevant info: Ingress SIP trunk: IP: 123.45.45.3456 DID's XXX-XXX-XX00-XX10 sip.conf: [general] useragent=Asterisk port=5060 context=default tos=lowdelay disallow=all allow=ulaw

I have some phones (and an ATA) that are shared between two users who each have separate voicemail but they are not behaving as desired nor expected. Incoming calls show up on the correct lines. Calls originating from the device are seen, at the terminating device, as coming from the account listed last in sip.conf, regardless of the line selected. This creates three main issues I would like

Hi I'm having a very odd phenomenon happening on our production server (1.4.17 and using realtime). Sometimes a call will disconnect 30 seconds after the SIP phone hits the mute button but it doesn't happen all the time. I've done a sip debug while watching this happen and that doesn't show anything other than a BYE message being sent out of the blue. The rtptimeout and

Greetings List. we're facing a strange case with my system where in the middle of the call .. after like 7 minutes (not necessarily ) the callee is unable to hear the caller however the caller is able to hear the called party. the scenario is the following. 1- 15 computers running Windows XP SP3 joining a Windows Domain Controller with DHCP , DNS, ISA Internet Acceleration Server. 2- Internet

I am using asterisk 13.33.0 and POlycom phone with the latest firmware. The polycom phone is behind a firewall, the server is in the cloud. If the polycom has just booted - it receives a call, after some time (couple minutes) it no longer receives a ring. I see no errors in the CLI - looks just like the previous call as far as I can tell. Then reboot the phone and as soon as its ready call it

Hi, I'm wondering - why SIP device state doesn't get updated to anything else, except Not In Use. For queue call (with Local channel) i get: app_queue.c: Device 'SIP/21168' changed to state '1' (Not in use) app_queue.c: Device 'SIP/21168' changed to state '1' (Not in use) app_queue.c: The device state of this queue member, Agent/21168, is still 'Not in