similar to: callerid not working over sip

I'm trying to connect a sip call from sipgate to Asterisk A to Asterisk B. Both are behind NAT, but port forwarded. I get the connection, but no voice - either in or out. I can call on SIP from A to B (and from B to A). Do it all the time. Asterisk A receives SIP calls from Junction and Teliax. CLI on A looks right: == Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 ==

Hello, We have a strange situation (asterisk 1.6.2.14), where we get a result for DIALSTATUS for BUSY and No-ANSWER, but nothing for CANCEL. This is the (relevant) test dialplan: -------------------------------- [incoming-private] exten => _X., n, Dial(SIP/1001,30) exten => _X., n, NoOp(${DIALSTATUS}) exten => _X., n, Gosub(incoming-status,s-${DIALSTATUS},1) [incoming-status] exten

Upgraded from 16.2.14 to 1.6.2.15 on Fedora 13, with aastra 9133i and 57i. On 9133i and 57i: #<extension># works for a blind transfer. Xfer<extension>Xfer doesn't! All this worked on 1.6.2.14. Nothing useful on cli, verbose 3, DEBUG. Here extension 169 answers an outside call, and tries to transfer it to 145 using the Xfer button: -- SIP/169-0000009c answered

Recently, I've been having issues with the URIs returned from e.164.org and toll free calls. It seems that the URIs that are returned from ENUMQUERY and ENUMRESULT are no longer the proper numbering schemes that the poviders use. I've been using the following [enum] template in my outbound route for quite some time with great success until recently. [enum](!) exten =>

With asterisk 1.8.7.0 has been running ok for months. Now, this morning, it's crashing. I can restart it, but it crashes after 10+ minutes. It dies like this -- Executing [s at macro-stdexten:2] Dial("SIP/teliax-00000019", "SIP/176,18,rtT") in new stack == Using UDPTL TOS bits 184 == Using UDPTL CoS mark 5 == Using SIP RTP TOS bits 184 == Using SIP RTP

This is a small 12 line system, internal extensions 150 - 180. I didn't have a phone on 151. Here's the sip.conf stanza: ;;[151] ;;type=friend ;;context=longdistance ;;callerid="Conf Room" <151> ;;secret=0000 ;;host=dynamic ;;qualify=yes ;;dtmfmode=rfc2833 ;;allow=all ;;defaultuser=151 ;;nat=yes ;;canreinvite=no There's no DISA. And then somehow (how???) ip address

Having an issue with receiving faxes, but when I pass through the fax. Currently, I receive the fax with Digium's Fax for Asterisk, store it and the initiate an outbound call to our fax server. (XMedius Fax). This works, but we would prefer to have Asterisk simply route the call directly to the fax server and take the store and forward out of the equation. When I do that, however, the

Dear list, I've got the following setup : [FAX-ATA]--[PBX LAN]--[Firewall]--[PBX WAN]-----[upstream SIP] On the PBX's we run Asterisk 1.4.33 with t38pt_udptl=yes in [general]. The FAX ATA is a Teles VoIPBox with T.38 support (that works). On the PBX WAN, i see the following in udptl debug : Sent UDPTL packet to 172.16.0.156:4460 (type 0, seq 184, len 32) Got UDPTL packet from

Hi, I have a problem with polarity reverse on answer I use asterisk 1.4.30 linux kernel version 2.6.27 dahdi version 2.2.1 and analog card is Sangoma a400 with fxo ports this is my config [trunkgroups]

I'm having an issue with CDR. Basically, I expect to have all "legs" of a call having the same linkedid and differing only by the sequence value. That does happen, but I'm getting null dst values after doing an attended transfer. I'm not sure if this is a bug or I'm doing something wrong. I'm running Asterisk 13.2.0. Here's the console log, step by step: First,

On 1.6.0.18-rc3 using app_fax.so, spandsp-0.0.5, anytime I use SendFAX asterisk restarts: [Nov 15 19:00:36] VERBOSE[17013] logger.c: -- Executing [s at fax-tx-test:1] ESC[1;36;40mNoOpESC[0;37;40m("ESC[1;35;40mSIP/nhi-rive rside-sip-00000000ESC[0;37;40m", "ESC[1;35;40mContext fax-tx-testESC[0;37;40m") in new stack [Nov 15 19:00:36] VERBOSE[17013] logger.c: --

Hi, I have the following dialplan. Problem is, if the user authenticates, * starts counting as billable seconds even if i hangup the phone before the called party answers..And also as disposition.. it accepts all calls authenticated as 'answered' If i commentout the authentication line everything works as it should be. How should i use authentication that, it should accept it as aswered by

Hello guys. When I am trying to send fax through T38 to linksys SPA (properly configured etc. - I have tried it with other systems), I'm getting error and fax is not delivered. I'm getting this errors in asterisk.log: WARNING[687] udptl.c: No UDPTL ports remaining ERROR[687] chan_sip.c: UDPTL creation failed WARNING[687] udptl.c: No UDPTL ports remaining then, couple lines down:

On Fri, Jun 16, 2017, at 10:49 AM, Michael Maier wrote: <snip> > > t38modem and asterisk are using > > m=image 35622 udptl t38 > ^^^^^ > > Provider uses > > m=image 35622 UDPTL t38 > ^^^^^ > > Could this be a problem? If I'm sending internal only, it's always > lowercase. Looking at the tests we have we

Have a question about implementing Call Rollover with my current extensions.conf configuration. [macro-stdexten] exten => s,1,Dial(${ARG2},20) ; Ring the interface, 20 seconds maximum exten => s,2,Voicemail2(u${ARG1}) ; If unavailable, send to voicemail w/ unavail announce exten => s,3,Goto(default,s,1) ; If they press #, return to start exten =>

Almost two years ago, a change between how AEL code is built into Asterisk dialplan between minor versions made clear the need to provide a sane entry point into AEL subroutines and that's how AELSub() born. With Asterisk 11 release, they way [stdexten] at extensions.conf is invoked changed from Macro to Gosub using the 'missing context feature' and this caused that any stdexten

Sorry for all the newbie questions. I really appreciate everyone's help today. Okay I've got outgoing and incoming calls working with no echo. yay! Now I'm having an issue with SIP extension to extension calling. Any time I dial another extension it goes right into voice mail. My extensions.conf is pretty small and rough but, here's what I have right now. Most of it was taken

I thought it was quite easy to implement but I cannot get one-touch recording to work. Here are the changes what I did: I restarted Asterisk after the change (because reload does not work for changes in features.conf). I press *1 on the Polycom IP600 phone to record a conversation but no new wav file appear in /var/spool/asterisk/monitor or elsewhere. Test A: Outside line calling in

Gentlemen, I have 3 faxes attached to an Asterisk. Fax - SPA2102 - Asterisk. 0851711201 and 0851711290 is on our WAN, no NAT. 0197673581 is outside our WAN and needs to be NAT'ed. Sending a fax from 0851711201 to 0851711290, no problem, switches to T38 and fax goes through. Sending a from 0197673581 to 0851711201, no problem as long as i dont enable T38 on 0197673581. But, if i enable T38

I am running asterisk 1.4 and the Digium GUI SVN-branch-2.0-r4489. When one phone calls another, I see the following on the console (here, 6223 dials 6123) -- Executing [6123 at DLPN_DefaultDialPlan:1] Macro("IAX2/6223-10489", "stdexten|6123|SIP/6123&IAX2/6123") in new stack -- Executing [s at macro-stdexten:1] Set("IAX2/6223-10489",