similar to: AOC advise of charge

> Hello everyone, > > I am trying to find out whether AOC (any of the 3 types) is currently supported by Asterisk and for which hardware combination. > > Does anyone know if? AOC info can be used in the CDR when the interface to the outside world is ISDN BRI (not pri) and the internal counterpart is an analog extension (dahdi, i guess)? What about sip or iax? > > I have found

Hi, I have a problem with dialing status. I'm using Asterisk 1.6 and a patton 4554 gateway for ISDN calls. When I call fixed telephone (not mobile phone) after few ringing the status change to "answer" but the phone is still ringing, so if I hangup before someone really answer, the call is reported as answered but it isn't. This gives me problem for call charge. Some I idea

Hello, is there someone who knows if I can use AOC for billing in Asterisk? I mean: let's say I have an external SIP device that produces AOC data. This device connects me to the telco network. Can Asterisk, if connected via SIP with this device, collect AOC data and put it in the CDR records? If not, which is the right way to use AOC for billing? Thanks a lot Stefano Corsi -- Stefano

Does Asterisk support Advice of Charge? I was told that my Telco sends me billing signalization that way, and I wonder can I use it? -- Tomislav Parcina ime.prezime@email.t-com.hr

Hi, i can see AOC messages on the asterisk console. Can i sendtext() them to the caller or put them in cdr? Regards, Andreas. _________________________________________________________________ Need a new job? Check out XtraMSN Careers http://xtramsn.co.nz/careers

Hi, Changing the line bellow helped to get incoming calls but I add to remove secret= option in sip.conf (otherwise, Patton wouldn't respond to 407 Auth required challenges). If someone could enable secret and still get incoming calls (in any SmartWare 5.X), please, do not hesitate to share here ... interface sip IF-ASTERISK bind context sip-gateway ASTERISK route call dest-table

Hi, I'm trying to configure a 4638 to pass inbound and outbound to and from ISDN and SIP interfaces. I'm using web interface at the moment. Setup is: ISDN -- <BRI> -- Patton 4638 -- <SIP> Asterisk -- <SIP> -- <IP Phone> I can call from IP phone but can't receive any incoming call : I can't see any SIP message coming in when a call comes in. Previously,

Hello all, I would like to get billing/charging informations of all outgoing calls of any PSTN numbers made with my IP-Phone via asterisk. Can I obtain in * an accurate charge information of outgoing call via CAPI which destination is any PSTN number? Does the ISDN "signal" contain charging informations ? Thank for advice Rastislav

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I'd like to know what is the current situation with regard to AOC-E, when Asterisk is inserted between the telco and an existing PBX, using E1 / EuroISDN. Can Asterisk pass the AOC-E information received from the telco to the PBX, so that billing system still works? The system would be for a hotel, so breaking billing system is not possible.

hi all, I'm trying to send text messages to Snom 300 to show the credit remaining during the call... Sending a MESSAGE directly to the phone via udp i'm able to update the text on the display... but not during the conversation. I read about AOC, but i can't find any documentation about Asterisk + SIP + AOC Have you any experience, docs or workaround to suggest? Thx Ale

Dear fellow list readers This is the situation: ISDN Devices => Patton ISDN to SIP GW => Asterisk PJSIP The Patton GW resides on a dynamic IP address, so I cannot really use match=ip in the identify section. The Patton does not send a line parameter. The ISDN Devices behind the patton have different MSN and should be able to send them in the From: Header, so the default endpoint

Hi all, I''m getting a very strange problem with a recent OpenSolaris b134 install. System is: Supermicro X5DP8-G2 BIOS 1.6a 2x Supermicro AOC-SAT2-MV8 1.0b 11 Seagate Barracuda 1TB ES.2 ST31000340NS drives If I have any of the 11 1TB Seagate drives plugged into the controller, the AOC-SAT2-MV8 BIOS appears to detect them just fine, but I get the following problems: 1. Grub takes a

Hi at all ! I've a problem and I don't know how to solve it. My configuration is the following: ISDN LINE ---> PATTON (SIP) ---> ASTERISK in asterisk my sip.conf for sip patton account is the following: [general] port=5060 bindaddr=0.0.0.0 context=default language=it limitonpeers=yes notifyringing=yes [acc1] context=fromPSTN_Ext1 type=friend qualifiy=yes host=dynamic

Hello Does anyone have any experience with configuring BT (British Telecom) ISDN2e lines to work with Patton SmartNodes? I have a Patton SmartNode 4638, which is now connected to 3 x ISDN2e lines - and in turn connected to our internal LAN. I'm having huge issues configuring the SmartNode to successfully "see" the ISDN channels - and to be honest, I'm lost as to how to then

Hello Does anyone have any experience with configuring BT (British Telecom) ISDN2e lines to work with Patton SmartNodes - and then Asterisk? I have a Patton SmartNode 4638, which is now connected to 3 x ISDN2e lines - and in turn connected to our internal LAN. I'm having huge issues configuring the SmartNode to successfully "see" the ISDN channels - and to be honest, I'm

Hi list, I'm evaluating a private telephony scenario of about 20 locations - 300 phones, 50 FAX machines. Initial overview points to the installation of asterisk at three locations connected to the PSTN via ISDN PRI. All other locations, small by themselves, would get SIP phones managed by asterisk, since there is good IP connectivity between all sites. Now on to the

Hello, I've discovered that in Italy ISDN lines can be programmed to generate a "billing pulse" every n seconds (it dipends from the pricebook). The pulse has these figures: frequency .................................................................... 12 kHz ? 1% level .......................................................................... 200 mVrms on 200

I'm not sure how much more simple I can make this but I just cannot seem to get my Asterisk 13 to accept a connection on the manager interface: --- manager.conf --- [general] enabled = yes port = 5038 bindaddr = 127.0.0.1 [myasterisk] secret=a permit=0.0.0.0/0.0.0.0 read = all write = all So, couldn't be any more wide open and simpler to connect yet: # echo -e "Action:

I''ve been trying to get either smartctl or sg3_utils to report properly. They both have the same low-level problems which leads me to suspect either I''m doing something wrong OR there is a problem in the marvell88sx / sd / SATA etc framework. I can access drive name/serial number of all drives on the SAT2 card and the temperature is returned from the IE log page on my two

Hi, I succesfully install spandsp chan_misdn and digium card. the rxfax works fine and I get the fax result by email. I would like to do the same using a Patton gw + zaptel but I can't receive fax anymore, the call comes in from ISDN in the Patton gw, patton sends it to asterisk, asterisk run a macro to make a tif file using rxfax, the tif file is correctly created but with a 0 size the call