similar to: Dahdi and FreePBX

Hello, My first attempt to get dahdi running on 1.4.28... with a Rhino 8 port modular card and a single FXS module. Got the Rhino card installed and the machine sees it: root at pbx:/etc/dahdi# dmesg | grep rcbfx [ 71.985309] rcbfx 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 71.985440] rcbfx 1: Rhino PCI BAR0 50100000 IOMem mapped at ffffc90008d7c000 [ 71.985504]

Hi Guys, Just did an Asterisk 1.6.x (repo install) and FreePBX (source install). When trying to dial a number, I get this: tel*CLI> Use of uninitialized value in hash element at /var/www/html/panel/ op_server.pl line 3367. Use of uninitialized value in concatenation (.) or string at /var/www/html/panel/op_server.pl line 3372. Use of uninitialized value in pattern match (m//) at

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

Hi to all, I use FreePBX version 2.7.0.2 with dahdi. The first problem is with dahdi: At the system startup i can't find a way to start correctly Asterisk with Dahdi. My boot configuration is the following: /etc/rc.d/after.local /usr/sbin/rcdahdi start & sleep 15 /usr/local/sbin/amportal start & /sbin/route add -host 85.38.234.9 gw 192.168.2.1 & /usr/bin/python

Hi all, I am probably missing something ultimately obvious, but I have a problem configuring freepbx... Using Edgy Eft with the cvs freePBX 2.2.1 and followed the Ubuntu installation guide on freepbx.org. System pxe-boots from a server with NFS root on same Using * 1.2 current (from source, not .deb's) Using mISDN-streams (from source, not .deb's) Using freePBX-2.2.1 (from source, not

I am really a beginner of PRI ISDN board, I am wondering if there is a "quick start" chan_dahdi.conf configuration I could use. I tried to install two "FreePBX" boxes follow the instructions from "http://www.cadvision.com/blanchas/Asterisk/DahdiT1trunk.html" connected them between PRIs, It worked. And now if I refer the FreePBX "chan_dahdi.conf" it looks

I am running Asterisk 1.6.1.6 and DAHDI/DAHDI tools 2.2.0.2 compiled from source on a Debian Lenny box, also running FreePBX 2.5.2. I also have an OpenVOX TDM400 card installed with an FXO port on port 1, and an FXS port on port 2. I have a POTS line installed and working on the FXO port. However I've encountered a weird problem that I can't seem to figure out. I have incoming POTS

Hi, I am using asterisk 1.4.28 with freepbx and Wildcard TDM410P card. Everything is working fine except the caller ID of incoming call from PSTN line. The phone display is showing "Unknown" when there is an incoming call. *My log file showing this while an incoming call on PSTN line:* tail -f /var/log/asterisk/full [Dec 30 06:36:16] DEBUG[2559] dsp.c: dsp busy pattern set to 0,0

I've got a piece of CPE equipment that has an FXS port that I have tied to an FXO port on a TDM400 clone card. Normally, if I go off-hook with a standard telephone connected to it, I get a dialtone. If I dial a digit, and send a hookflash, the device will provide a dialtone back for the next available channel on the device. I'm trying to recreate this same behavior with Asterisk,

Dear list, I've set up an RPM repository with several asterisk-related RPMs that I think contain some improvements upon what are already out there. The first goal is to be able to build an Asterisk + FreePBX system on CentOS 5 with the EPEL repo enabled; in our environment, where all our systems are under configuration management, either an appliance-type solution or a manual

I am unable to dial out over a Wildcard TDM400P. This was working previously, so must have messed up the config somehow. I'm running Asterisk 1.6.0.15, with FreePBX 2.5.2.2. When I dial, I see: -- Executing [s at macro-dialout-trunk:19] Dial("DAHDI/1-1", "DAHDI/g0/9239220,300,") in new stack == Everyone is busy/congested at this time (1:0/1/0) It looks like the

Dear all, i have a problem with a system running - Ubuntu 10.04 ( all updates done ) - ii asterisk 1:1.8.5.0-1digium1~lucid Open Source Private Branch Exchange (PBX) - ii asterisk-dahdi 1:1.8.5.0-1digium1~lucid DAHDI devices support for the Asterisk PBX I also use freepbx 2.9 for the configuration. Hardware is a Dell R410 and a Digium

Hi All, I have installed asteriskNow with Asterisk 1.6.2.11 and FreePBX 2.7.0.10. I have configured x100p fxo card in my asterisk box. But in my cli mode i am not getting the command *"dahdi show status"* Output of CLI : astrisks*CLI> *dahdi show status* No such command 'dahdi show status' (type 'core show help dahdi show' for other possible commands) I

Hi, I know it sounds weird, and this is part of the reason I have not reported that sooner. As I upgraded from 1.6.2.x to 1.8.x several months ago I am experiencing this problem. If a call is initiated from a DAHDI extension after no DAHDI extensions were used for some time, arbitrary DTMF digits are skipped and the call fails. If the call is redialed it goes through. Normally just one (1)

Hello, I seem to be having an issue with the configuration of my PRI on a new asterisk server I've created to replace an old install that I have. The card is Digium Wildcard TE133. I continually get messages like "Primary D-Channel on span 1 down", rather irregularly: [2013-07-29 17:31:39] VERBOSE[3621] sig_pri.c: == Primary D-Channel on span 1 up [2013-07-29 17:31:39]

hello: Does asterisk-16.1.1 support freepbx by default? /contrib/scripts/install_prereq install ./configure make make install make config make freepbx // I run this command without success. after then, we can access the freepbx GUI? this website show it work: https://www.sinologic.net/2018-12/la-ultima-version-de-asterisk-16-incluye-un-comando-para-instalar-freepbx.html --------------

Arch = x86_64 OS = CentOS-6.4 (freepbx) Asterisk = 11.4.0 FreePBX = 2.11.0.2 Snom870 Handsets We are in the process of moving to an Asterisk based PBX. At the moment most things work as we wish. However, I have just notices that when I force a reload using 'amportal a reload' I see this loop start in 'asterisk -rvvvvvvvvvv': > Channel Local/s at tc-maint-000002a4;1

do you have selinux enabled? It should not be. p p.s. - if it comes to re-installing, you can backup all your settings with the freepbx backup utility and then restore so that you don't have to re-enter everything. From: "Lachek Butalek" <lachek@gmail.com> To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Date:

Some recent issues I had with hardware seem to come back to not understanding two very similarly named files: /etc/asterisk/dahdi-channels.conf /etc/asterisk/chan_dahdi.conf I've modified the chan_dahdi.conf to work now, but it would appear all I needed to do was include dahdi-channels.conf in chan_dahdi.conf and the problem would not have persisted? Is it me or is that a bit Monty Python?

Hello all, The Asterisk Management Portal (AMP) is now known as FreePBX. FreePBX 2.0.1 is now available for download. A **BIG** thank you goes out to the project developers for all their hard work, and to beta testers for running FreePBX through it's paces! This exciting new release boasts a better user experience, additional functionality, and a new module system. The module system is