similar to: sip show channels display

Dear list, I am trying to re-analyse something. I do have two time series, one of which (ts.mar) might help explaining the other (ts.anr). In the original analysis, no-one seems to have cared about the data being time-series and they just did OLS. This yielded a strong positive correlation. I want to know if this correlation is still as strong when the autocorrelations are taken into account.

vps*CLI> iax2 show channels Channel Peer Username ID (Lo/Rem) Seq (Tx/Rx) Lag Jitter JitBuf Format 0 active IAX channels vps*CLI> core show channels Channel Location State Application(Data) 0 active channels 0 active calls vps*CLI> sip show channels Peer User/ANR Call ID Seq (Tx/Rx) Format

Has anyone seen this before? This channel is consistently present on both of my asterisk servers. Sometimes they disappear for a few seconds and then come back. It always has the same Call ID. voip1*CLI> sip show channels Peer User/ANR Call ID Seq (Tx/Rx) Lag Jitter Format 192.168.0.102 (None) df92fb1b-8a 00101/03059 00000ms 0000ms UNKN

Hello Everyone, I'm looking for help/ideas on how to do the following: I have a couple of people out of many (the couple of people randomly change) who log into an "on-call" queue. A call comes in and it rings the "on-call" extensions, but no one answers. I would like the call to then try the cell-phones of just the people that are logged into the "on-call"

My sip show channels shows some channels active that I can not make sense out of, and they have been that way for days, so I am pretty sure they are orphans. Is there a way to show active CALLS (instead of channels) to try and determine the source? Does the output below provide any clues as to why these channels might show active? Anyone aware of related bugs? The #'s indicate original

Hi! I'm trying an asterisk-FWD connection. I'm using X-Lite OR SIPPS as the IP phone. I configured the X-Lite and SIPPS to use GSM codec. Whe I call FWD, I get this info on the channels when the call has not been stablished yet: sip show channels Peer User/ANR Call ID Seq (Tx/Rx) Lag Jitter Format 192.246.69.223 613 1770bf3430d 00102/00000

Hi all, i'm trouble with codec setup on an asterisk machine 1.4.18 and some Thomson ST2030 as extensions. In the users.conf file for internal extension i have: disallow=all allow=g729 allow=alaw allow=ulaw Without any codec installed (i mean with original g729 of asterisk) all go fine, calling from an extension to one other: Peer User/ANR Call ID Seq (Tx/Rx) Format

I'm having an oddball issue with a Polycom SoundPoint IP 500. As you can see below Asterisk thinks there are 2 SIP channels active, but show channels tells me there are no calls active. Anyone have any idea why this is happening? The Polycom occasionally stops accepting calls and requires a power cycle. fs-1*CLI> sip show channels Peer User/ANR Call ID Seq

Hi all, I have a question regarding pending (zombie) SIP sessions: on Asterisk CLI, with command 'sip show channels' , I see two channels in use with callID and other infos detailed; also 'sip show inuse' give me same result (in terms of channels usage): Peer User/ANR Call ID Seq (Tx/Rx) Format Hold Last Message xx.xx.xx.79 209

Hi all, I have a Cisco 1760 gateway and and Cisco 7960 VoIP phone running via Asterisk. Both are running g711A codecs and SIP. On inbound calls I get a native bridge, however on outbound calls I never get a native bridge. With other SIP gateways I do get a native bridge on the outbound call. My sip.conf is as follows: [cisco1760] type=friend context=incoming host=192.168.0.55 insecure=yes nat=no

Hi, I am using Trxibox 2.6 latest ISO install. Following is the output of : "sip show channels" [trixbox ~]# /usr/sbin/asterisk -rx "sip show channels" Peer User/ANR Call ID Seq (Tx/Rx) Format Hold Last Message 212.53.40.40 0218245 6cfb845d050 09011/00000 0x0 (nothing) No 192.168.1.116 (None) YTc4ZmM3NjV 00101/00006 0x0

I am using a2billing as calling card platform with asterisk 1.2.17. After running for several days, if I issue 'sip show channels' command, I got a lot of dead sip channels although 'show channels' command only show 5 channels. What cause these dead channels? How can I clean out these dead channels? Will they pose any problem to my * server if left alone? What does this (d) mean?

Hi, I'm wondering if this is normal asterisk behaviour: asterisk*CLI> sip show channels Peer User/ANR Call ID Format Hold Last Message Expiry Peer 10.12.0.2 (None) 3c2f7ff2975e-wp 0x0 (nothing) No Rx: PUBLISH <guest> 10.12.0.2 (None) 3c2f7f21b71b-9q 0x0 (nothing) No

Hello everyone, I'm getting DIALSTATUS=CHANUNAVAIL when a call is trying to get one of my queue interfaces, despite the fact it is free at that time, can you give help? 1. I see many sip channels from that extension: [root at mysweetpbx]# asterisk -rx "*sip show channels*" |grep 648 Peer User/ANR Call ID Seq (Tx/Rx) Format Hold

Hello all I've discovered that SIP channels sometimes get stuck in *. I've read some posts from Fri 29 Aug 2003 which mentions this issue, but there doesn't seem to be any final answers I don't know if this is related to the 0001604 bug? Below is a list from one of the incidents: I know the (d) means that it is scheduled for destruction but the 10.1.1.45 channel hasn't

Can someone recommend the best way to view current calls in progress on the Asterisk console? Neither the 'show channels' or 'sip show channels' commands are easy to read. hestia*CLI> show channels Channel Location State Application(Data) SIP/2944093-f9e2 (None) Up Bridged Call(SIP/2944079-e7f2) SIP/2944079-e7f2

I'm trying to compile chan_mobile for asterisk 1.4 I've installed 1.4 from SVN and downloaded addons from SVN also. I make ./configure, make menuconfig, select only chan_mobile, and make. Then I obtain the following errors. (I've also tryed applying the patches I found at http://www.chan-mobile.org/?page_id=5 but with no better results. make[1]: Entering directory

Hi. I'm trying to get a list of the channels currently in use on an Asterisk server (1.8.32.1 if it matters) over AMI. I send the command "sip show channels", and I get back a response along the lines of (* used to protect the innocent...): Peer User/ANR Call ID Format Hold Last Message Expiry Peer *8.22.*0.34 02035644444

I made the post below earlier today. I'v since removed all NAT from the equation and the problem still persists. Basically I am trying to transfer a call. The transferring phone sends a REFER message to asterisk with a call id that Asterisk doesn't know about. Surely, surely.... someone else must have seen this? hermes*CLI> sip show channels Peer User/ANR Call ID

ANR is a international news station we were testing on icecast over the weekend the quality great we chose mp3 because anyone can hear it. linux, mac. or windblows. also wanted to use a linux server, which is far more reliable than a windows machine ( always dropping out for some reason ) If the ogg only rule is permanent we will have to talk very nicely to our system admin to switch to ogg with a