similar to: Avaya 9650 SIP phone and dial timeout

Hi! Trying to figure out what I am doing wrong... 1 std SIP phone (0317998975) registered to an Asterisk (SVN-trunk-r234256) 1 Cell phone 00733025975 attached through H323. extensions.conf exten => 975,1,Goto(975-${DEVICE_STATE(SIP/0317998975)},1) exten => 975-INUSE,1,VoiceMail(0317998975 at inputinterior.se,bs) exten => 975-INUSE,2,Hangup() exten =>

Hi all! I am trying to figure out how DEVICE_STATE is working, no luck so far. sip.conf [0317998975] type=friend regexten=0317998975 secret=???? username=0317998975 callerid="Magnus Benngard" mailbox=0317998975 at inputinterior.se host=dynamic canreinvite=yes dtmfmode=rfc2833 nat=yes disallow=all allow=alaw extensions.conf exten => 0317998975,hint,SIP/0317998975 exten =>

Gentlemen, Forgive me if I am posting at the wrong place! I was going to test the "new" chan_ooh323 driver so I did install: debian: Linux sip2 2.6.26-2-686 #1 SMP dahdi-linux-complete-2.2.0.2+2.2.0 Asterisk SVN-trunk-r231692 Did enable chan_ooh323, everything compiled without any problems. Hardware setup: Phone (975) - Avaya CM - H.323 - Asterisk - X-Lite (0317998975) X-Lite can

Hi! Part of extensions.conf: exten => 985,1,Dial(SIP/0317998985&H323/00702221448 at Avaya,20) exten => 985,2,Goto(985-${DIALSTATUS},1) exten => 985-BUSY,1,VoiceMail(0317998985 at inputinterior.se,b) exten => 985-BUSY,2,PlayBack(vm-goodbye) exten => 985-BUSY,3,HangUp() exten => 985-NOANSWER,1,VoiceMail(0317998985 at inputinterior.se,u) exten =>

Hi! We have alot of users who are having 2 phones, 1 fixed and 1 DECT. I am looking for a way to log them into a queue and let both phone rings. Let me try to explain: 0317998975 is a fixed phone, 0317998985 is a DECT. 0317998989 is a queue. queue add member SIP/0317998975 to 0317998989 works ofc. sip*CLI> queue show 0317998989 0317998989 has 0 calls (max unlimited) in

Hi! Trying to figure out how to rewrite calling number of an incoming call... A cell phone (0733025975) dials a X-Lite (977). X-Lite "shows" 733025975 at the display, but I want it to be 0317998975. I thought i could do something like: exten => 977/733025975,1,Set(CALLERID(number)=0317998975) exten => 977,n,Dial(SIP/0317998977) [Dec 14 19:07:43] NOTICE[20731]: chan_h323.c:2272

Gentlemen, Did tryout "CONNECTEDLINE" function, was exactly what I have been looking for. But there are at least one thing I cant figure out. Did a very simple and "stupid" extension 0317998955 and ran a test. My phone (0317998975) dials 955, the display on my phone changes from "955" to "Connected Line 955" when my call is answered, shouldn't the

Hi! Did play around with queues and need some help. I thought that MEMBERINTERFACE and MEMBERNAME should be set to the ?device? the call was queued to not the device that called the queue, or do i miss something? Running: Asterisk 1.8.2.3 built by root @ sip on a i686 running Linux on 2011-01-31 13:38:23 UTC 0317998985 calls Kinna (0320209030) Tomas Ekman (SIP/0317998972) receives the call but

Wait a second... Action: DBGet\r\nFamily: DS\r\nKey: 0733025975\r\n\r\n In the dialplan: exten =3D> 0106024975,1,Set(DB(DS/0733025975)=3DINUSE) exten =3D> 0106024975,n,Hangup() exten =3D> 0106024976,1,Set(DB(DS/0733025975)=3DUNAVAILABLE) exten =3D> 0106024976,n,Hangup() Just a short call to my cell phone, to se if i get anything back, my = cell phone doesn=E2=80=99t even ring. Wait

Hi, Did a test with Local, exten => 1234,1,Dial(Local/1 at agents) [agents] exten => 1,hint,SIP/0317998975&SIP/0317998985 exten => 1,1,Dial(SIP/0317998975&SIP/0317998985) When calling 1234, both 0317998975 and 0317998985 rings when answering in 0317998985, 0317998975 stops ringing, all fine but when answering in 0317998975, 0317998985 keeps on ringing... 0317998975 is an Avaya

Hi, I am looking for a way to check the status of a cell phone. Found one way that worked for me and would like to have some feedback or suggestion of improvments. Below example is for a ?Swedish? cell phone, dont know if it works in the same way for other countries. I could define ?redirecting? numbers for 3 traffic cases when u dial my mobile (073-302 59 75): NOT_INUSE call forward to A INUSE

Gentlemen, I have 3 faxes attached to an Asterisk. Fax - SPA2102 - Asterisk. 0851711201 and 0851711290 is on our WAN, no NAT. 0197673581 is outside our WAN and needs to be NAT'ed. Sending a fax from 0851711201 to 0851711290, no problem, switches to T38 and fax goes through. Sending a from 0197673581 to 0851711201, no problem as long as i dont enable T38 on 0197673581. But, if i enable T38

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I must be missing something here but I can't figure out why I can't get DEVICE_STATE() to give me anything other than "NOT_INUSE". I have two extensions: 6666 and 6668. I used 6668 to make a call to yet another phone, so I know that it's busy. I then use 6666 to call 6668 and in the dialplan have a noop to see what

Hi! Have probably not understand how fax is working in Asterisk 1.6. I did install: ptlib-v1_12_0 h323plus-v1_19_7 dahdi-linux-complete-2.2.0.2+2.2.0 spandsp-0.0.5 asterisk-1.6.2 asterisk-addons-1.6.2 make menuselect in asterisk-1.6.2 source directory shows: [*] app_fax But "core show applications" doesnt show me any "fax applications" and when I try to receive a fax:

Hi all! First of all i would like to say that i am not a Samba4 guru so my question may be "stupid". I have 2 Samba4 servers up and runnning: Server 1: netbios name = PDC workgroup = GBG realm = GBG.INPUTINTERIOR.SE server role = domain controller Server 2: netbios name = PDC workgroup = MLM realm = MLM.INPUTINTERIOR.SE server role = domain controller Here comes my

Morning, Have some questions regarding receiving and sending faxes... 1:st example: exten => 101,1,Answer() exten => 101,2,Wait(3) exten => 101,3,ReceiveFAX(/var/spool/asterisk/tmp/fax.tiff) exten => 101,4,System(tiff2pdf -p A4 /var/spool/asterisk/tmp/fax.tiff > /var/spool/asterisk/tmp/fax.pdf) exten => 101,5,System(mutt -s 'New FAX for you sir' -a

Hi We have an operator that his device state on all queues is "In use" where it should be "Not in use". how can we manually change the state of a device? I looked into the devstate function and tryed the following: perfpbxr*CLI> devstate list perfpbxr*CLI> --------------------------------------------------------------------- --- Custom Device States

One of my sites asked for a way to identify if the person they are calling on another extension is already on another call. To that end, I wrote a bit of code in the dialplan for my extensions that checks to see if the extension they are dialing has a device status that is anything other than NOT_INUSE. If the device is NOT_INUSE, then it dials the call normally. If it has a different status,

You can use a custom device state to do it. [dnd] ;DND Toggle exten => *363,1,Answer() same => n,Set(CURRENT_PRESENCE=${DEVICE_STATE(Custom:DND${CHANNEL(peername)})}) same => n,GotoIf($[${CURRENT_PRESENCE}=NOT_INUSE]?*78,1:*79,1) ;DND On exten => *78,1,NoOP(Turning DND On) same => n,Set(DEVICE_STATE(Custom:DND${CHANNEL(peername)})=BUSY) same =>

Hello Have a setup of asterisk with realtime SIP devices. Trying to organise monitoring of my SIP devices. Once device registered, its state becomes NOT_INUSE (result of DEVICE_STATE(SIP/device) function). Simulating of device breakage - powerdown it. Waiting for a while (minute or two), retrieving DEVICE_STATE(SIP/device) again - no changes! Awaited UNAVAILABLE. doing from CLI: sip qualify peer