similar to: zttool don't show NT mode with OctoBRI

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi, I'm pulling my hair down and getting bold :-) ..... I have Asterisk between Panasonic KXTD816 and Euroisdn in Italy (beronet octobri and bristuff Asterisk).... I'm trying to do just plain transfer of call from pbx to ISDN through Asterisk... It seems like PBX hangsup, when call is progressing with no apparent reason. I'd kindly ask for any advice or some working example for

Hello, In my system, dmesg outputs : [ 13.039788] wcb4xxp 0000:01:0a.0: probe called for b4xx... [ 13.039788] ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 21 (level, low) -> IRQ 21 [ 13.039788] wcb4xxp 0000:01:0a.0: Identified HFC-8S Junghanns.NET octoBRI PCI (controller rev 1) at 0001dfe0, IRQ 21 [ 13.041202] wcb4xxp 0000:01:0a.0: NOTE: hardware echo cancellation has been disabled [

BUG/SYMPTOMS: 1.Under certain circumstances, octoBRI (and most likely quadBRI) ISDN cards (Junghanns/CologneChip) severely distort certain ISDN payload. 2.Although these claims relate to the bristuff patch, the problem might not be limited to bristuff and in fact be rather asterisk/zaptel/libpri related. 3.Signal distortion is limited to the use of the CVS version of the Bristuff patch for

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |

Hi, I'm using revision 6822 of Dahdi Tools. # dahdi_hardware pci:0000:05:06.0 wcb4xxp+ d161:b410 Digium Wildcard B410P # asterisk -rx "dahdi show version" DAHDI Version: 2.2.0.2 Echo Canceller: OSLEC # cat /etc/dahdi/genconf_parameters ... pri_termtype SPAN/1 TE SPAN/2 TE SPAN/3 NT SPAN/4 NT #

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment***************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ****************************************************************** In my case , I set prot 1 and

Hi there, I am attempting to set up a simple BRI and SIP based platform using * with the quadbri card (it's not sharing an IRQ). I enclose my zaptel and zapata.conf files. For the inital test I'm simply trying to connect to the * demo menu. The drivers compile (with a few warning that I believe aren't important - see attachments). chan_zap comiles with the warning: chan_zap.c:

Hi, I mistakenly posted this to Dev list.... I wonder if I use quadbri or octobri cards to insert Asterisk between ISDN PBX and ISDN line - if power of Asterisks fails - will those card connect PBX directly to ISDN line ? If not are there any other simple switching devices, that would do this (in power fail it will connect ISDN PBX to ISDN lines directly) ? Thanks in advance, regards, Rob.

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment********************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ******************************************************************** In my case , I set prot 1

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

Hi, When typing dahdi_scan on an OctoBRI-enabled setup, I've got only 8 replies such as : [1] active=yes alarms=RED ... [8] active=yes ... framing=CCS I would expect 16 replies (one per B-channel). Is this correct ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, In my 1.6.1.18 with dahdi 2.2.1.1, I've got : # dahdi_hardware pci:0000:01:0a.0 qozap- 1397:16b8 Junghanns OctoBRI ISDN card Does it mean I should download and use qozap or is it a bug in Dahdi ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100412/de87e46e/attachment.htm

Hello, Using libpri-1.4.7 and asterisk-1.6.0.1, I've got "Unknown signalling method 'bri_cpe" when "module load chan_dahdi.so". Googling with "chan_dahdi bri_net" don't help much. Shall I upgrade to 1.6.1rcXXX to get 'bri_cpe" support ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Please forgive me, if I misunderstand the problem completely. Following instructions in several german blogs, I want to configure Asterisk with a hfc-pci card, an old NTBA and an ISDN phone as a SIP device. It seems that I have to set signalling in zapata.conf to bri_net_ptmp. When I do this, Asterisk will hang if started with -vvvvc, the last lines of output being: [res_features.so] =>

I got the same problem, and what i change it was point-to-point to point-to-multi-point, and I used normal patch cable to connect the ISDN card to ISDN connector, and I used TE mode. In italy work like that I hope that will help you, I used also bristuff. Good luck ________________________________ Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]

I have a serious problem that repeats very often, after 30 - 50 calls and I can only solve it by stopped and restarting * :-( After a while, * seems to loose track of something. When an ISDN call from PBX needs to go to the Telco, I get 'Ring requested on unconfigured channel 255/255 span 2' It's always channel 255/255 ??, the 'span' number is random Setup: * between Local

Hi all, I am having trouble setting the signalling method for the B410P using DAHDI. Asterisk complains that it has never heard of 'bri_cpe' or 'bri_net' - but it doesn't mind having 'pri_cpe' etc. ERROR[4294]: chan_dahdi.c:11327 process_dahdi: Unknown signalling method 'bri_net' Dahdi - dahdi-linux-complete-2.1.0.4+2.1.0.2 Asterisk - 1.4.23.1 Libpri - 1.4.9

Hi all, I just posted this question before last week. Meanwhile after upgrading Asterisk 1.0.7-BRIstuffed-0.2.0-RCg to 1.0.8-BRIstuffed-0.2.0-RCh the same problem occurs, but seems to be more seldom. Attached is now the output of "zap show channel" . - I'm running a stable Asterisk on a HP DL380G2 1.4Ghz 0,5GB RAM equipped with 1x TE410P and 2xJunghanns OctoBRI running in NT-mode.