similar to: Experience with LLDP

How do you require a password for a voicemail box? I have been searching all day, and can't find any type of "security" setting for voicemail. I am looking for some what to have some minimum security like "no blanks, can't be the same as the extension, can't be sequential numbers or repeated numbers". I know that not all of these options may exist, but there has

We are currently moving away from a wide-spread Cisco CallManager deployment to Asterisk. For many of our small sites we have the routers configured for what Cisco calls SRST so if we have a WAN failure, the router acts as a SCCP registrar. We are converting to SIP, and from what I can tell Cisco wants a license for each router to run SRST over SIP... So my question to the group is: What are

We are connecting a new device to our voice system, and the vendor has a whole list of "supported" network devices and associated parameters for the Telco to adjust... Yes, it's the telcos issue... Anyway, out of all of the swtich types that dahdi can emulate, what is the most complete/tunable solution? The premise for those interested is a PRI connection to a Dialogic card,

Hi, Has anyone heard of SIP phones supporting LLDP-Med ? Mitel or Avaya phones are supposed to support it but I don't if it applies to SIP firmware enabled hardphones or not. Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080131/b456f797/attachment.htm

Hi, all. I see that the Polycom SoundPoint IP 330 supports VLAN... but I don't quite see how that works. Do you point a non-VLAN'd segment at it (akin to when you uplink a VLAN_enabled switch), and have the phone implement the VLAN? Or...? *puzzled* Thanks much, -Ken

Hi, (I think) I followed instructions here ( http://www.voip-info.org/wiki/view/Firmware+issues+on+7940+-+7960 section "Notes added Nov 2005, revised May 2006:" at the bottom of the page) to factory reset a Cisco 7942 I wanted to configure to SIP firmware. When booting, I can see this requesting and obtaining file term42.default.loads from TFTP server. Then it would send a request

In 2012 QEMU added UDP unicast network backend support https://github.com/qemu/qemu/commit/0e0e7facc775e9bb020314f48751b3d09f316c8b#diff-a0a1810b6e249e68f1a290e37399becb Checked latest libvirt on the git repo, and didn't see this as an option. So tried to use the mcast tunnel mode. I keep getting duplicate packets with BPDUs and LLDP packets going between the Point to point connection

Hi Everyone, I am running DD-WRT on a router that feeds about 30 Aastra 6753i. The phones occasionally go into "No Service" mode. The POE switch doesn't seem to be the problem as it's tested fine. I think the router sometimes gives up and comes back quickly. Or something of that nature. However, the connections are maintained if a call is going on because there are peer to peer

I can think of several potential differences. ?You may miss any bridge specific traffic (STP, LLDP) using the interfaces generated by the bridge itself. If you have vlan tagged sub interfaces you might also miss that traffic if you were snooping a particular interface. Obviously you will miss any on-wire broadcast traffic specific to the layer1 connection a particular interface was connected to

Hi, This set of patches contains the initial implementation of the IEEE 802.1Qbg standard: code for the exchange of EVB TLVs in LLDP frames to negotiate VSI capabalities as well as VDP VSI TLVs between a host with virtual machines and an adjacent switch. It supports setting the parameters of the TLV exchange from the command line using lldptool. VDP profiles consisting of

Hi, This set of patches contains the initial implementation of the IEEE 802.1Qbg standard: code for the exchange of EVB TLVs in LLDP frames to negotiate VSI capabalities as well as VDP VSI TLVs between a host with virtual machines and an adjacent switch. It supports setting the parameters of the TLV exchange from the command line using lldptool. VDP profiles consisting of

Hi, this set of patches contains the initial implementation of the IEEE 802.1Qbg standard: code for the exchange of EVB TLVs in LLDP frames to negotiate VSI capabalities as well as VDP VSI TLVs between a host with virtual machines and an adjacent switch. It supports setting the parameters of the TLV exchange from the command line using lldptool. VDP profiles consisting of

Hi, this set of patches contains the initial implementation of the IEEE 802.1Qbg standard: code for the exchange of EVB TLVs in LLDP frames to negotiate VSI capabalities as well as VDP VSI TLVs between a host with virtual machines and an adjacent switch. It supports setting the parameters of the TLV exchange from the command line using lldptool. VDP profiles consisting of

Hi, This series of patches contains the second part of an initial implementation of the IEEE 802.1Qbg standard: code for the exchange of VDP VSI TLVs between a host with virtual machines and an adjacent switch. VDP profiles consisting of mode,mgrid,typeid,typeidversion,instanceid,mac,vlan can be given to lldpad with lldptool. A way to deliver profiles to lldpad from libvirt using netlink

Hi, This series of patches contains the second part of an initial implementation of the IEEE 802.1Qbg standard: code for the exchange of VDP VSI TLVs between a host with virtual machines and an adjacent switch. VDP profiles consisting of mode,mgrid,typeid,typeidversion,instanceid,mac,vlan can be given to lldpad with lldptool. A way to deliver profiles to lldpad from libvirt using netlink

Hi, this set of patches contains the initial implementation of the IEEE 802.1Qbg standard: code for the exchange of EVB TLVs in LLDP frames to negotiate VSI capabalities as well as VDP VSI TLVs between a host with virtual machines and an adjacent switch. It supports setting the parameters of the TLV exchange from the command line using lldptool. VDP profiles consisting of

Hi, this set of patches contains the initial implementation of the IEEE 802.1Qbg standard: code for the exchange of EVB TLVs in LLDP frames to negotiate VSI capabalities as well as VDP VSI TLVs between a host with virtual machines and an adjacent switch. It supports setting the parameters of the TLV exchange from the command line using lldptool. VDP profiles consisting of

Hi, this set of patches contains the initial implementation of the IEEE 802.1Qbg standard: code for the exchange of EVB TLVs in LLDP frames to negotiate VSI capabalities as well as VDP VSI TLVs between a host with virtual machines and an adjacent switch. It supports setting the parameters of the TLV exchange from the command line using lldptool. VDP profiles consisting of

Hi, this set of patches contains the initial implementation of the IEEE 802.1Qbg standard: code for the exchange of EVB TLVs in LLDP frames to negotiate VSI capabalities as well as VDP VSI TLVs between a host with virtual machines and an adjacent switch. It supports setting the parameters of the TLV exchange from the command line using lldptool. VDP profiles consisting of

Hello everyone and Timo in particular, about a year ago I implemented a SHA-1 variant of the HMAC(-MD5) present in Dovecot. I had always disliked this a bit, because it replicates a lot of code. This patch generalizes the HMAC function to take a hash_method struct as parameter, and changes existing code which uses the "old" HMAC function to use this new one. I'm not really sure