similar to: ZAP/DAHDI outgoing faxdetect

Hi folks, I was hoping that someone might be able to help clarify some confusion I have on DAHDI Fax detection after spending some time searching. My understanding is this: 1.) Echo cancellation is automatically disabled upon recognition of a CNG tone, regardless of the faxdetect setting. This can only be disabled at compile time. 2.) faxdetect=incoming will, upon detection of a CNG tone,

Hi, I have a PRI euroisdn link between an Alcatel PBX and Asterisk. I'm having some trouble with overlap dialing. Suppose I dial '874053' from an Alcatel extension ('7034') where '87' is an Alcatel prefix of type "ARS Prof.Trg Grp Seiz.with overlap". I'm expecting Asterisk to receive '1004053' (where '100' is a prefix which always shows

Hi, I'd like to know what's the most "popular" method for automatic fax/voice detection for incoming calls on mISDN cards such as the B410P (hfcmulti). I'm running: kernel 2.6.17 misdn 1.1.3 asterisk 1.4.21.2 B410P card I'm using iaxmodem and hylafax with asterisk (the setup works for zap channels). I've used the following options in /etc/asterisk/misdn.conf:

Hi, I've noticed that a small but meaningful quota of calls from my Alcatel PBX to Asterisk are failing. This does not always happen and it is not easily reproducible but on high traffic I do get a large number of cases. Example: Alcatel PBX extension 7085 calls Asterisk PBX extension 6145 over a PRI E1 link. I see this in the Asterisk log: Dec 14 14:10:31 VERBOSE[11378] logger.c: --

My Asterisk fax detection used to work, but no longer does. OK. So, here's the deal: 1. It appears that the "faxdetect" command cannot be applied channel-by-channel in zapata.conf anymore, as Asterisk appears to the last "faxdetect=" command to ALL channels. 2. My stations are detected and sent to the proper extension; i.e., when I send a fax from one zap extension

Hi *, now for a long time i am trying to set the outgoing callerid, without luck. I am here in Germany, my asterisk has a pri interface connected to a PMX installed by Telekom. All telephone calls are preselected to EcoVoice. I am using asterisk 1.2.7.1, zaptel 1.2.5 and libpri 1.2.2. A week ago we tried with a device able to simulate a telephone system so send out a callerid, and that

hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes

Nik, Just curious - what is your telco setup? Do you have PRI with the specified D channels? You need to make sure that your telco is set up to have the D channels on 16 and 47. When you first start Asterisk, or when you log on to the CLI, do you ever see messages stating the B channels are successfully started? Let us know. -MC -----Original Message----- From:

Hi all, I wanted to switch from my current setup (mISDN) to the native dahdi with b410p support (wcb4xp). All works fine for normal phone calls but not for faxing. Faxes are distorted, if arriving at all, and hylafax logs the usual bad stuff (HDLC frame not byte-oriented.) Our setup uses a digium b410p card with asterisk 1.6, latest libpri and dahdi, hylafax with iaxmodem, and all this on 1

Hi, I'm trying to set a rule to dial out through multiple Zap groups so that, say, g0 is the cheaper POTS lines group and must be used first. However, if g0 is busy or disconnected then try dialing out g1. My g0 group is made up of 4 analog lines connected to a 4-FXO card. I disconnected the RJ-11 wires from the FXO card to simulate a line disconnection. So theoretically all calls should

Hello, I'm fairly new to asterisk and Trixbox, I'm setting up a Trixbox based email to fax gateway. At this time, I have a ZAP PRI link between the eFax server and my VoIPSwitch. The ZAP channels are configured, the B and D channels are up, and I have green link lights on either end of my cabling, but when I dial the number I have assigned to my eFax server, the call never seems to route

I have a TDM400 running telco lines on ZAP2-4 My after hours config is supposed to receive the incoming call then divert it to my home phone by calling out one of the other zap channels available. console output as such... Starting simple switch on 'Zap/3-1' -- Executing Dial("Zap/3-1", "ZAP/G1/0823274210") in new stack Aug 20 19:06:44 NOTICE[646]:

Hi to all. My asterisk pbx has a tdm400p card with 2 FXO cards on it. I configured the extensions.conf to send all the call incoming from that zap channels to an IVR system. I see in the asterisk CLI the call incoming and the playback of the message custom/myfile but no sound is played on the channel, i cannot hear nothing. If I change the configuration and i send the call to an internal sip

Hi, I know it sounds weird, and this is part of the reason I have not reported that sooner. As I upgraded from 1.6.2.x to 1.8.x several months ago I am experiencing this problem. If a call is initiated from a DAHDI extension after no DAHDI extensions were used for some time, arbitrary DTMF digits are skipped and the call fails. If the call is redialed it goes through. Normally just one (1)

Hello List, it is a very long time since I wrote here.... It has been still in Zaptel times.... Today I am run into a related problem: I can't get a DAHDI setup to work 100%. I am configuring an Astribank XR00013 (BRI, two ISDN ports). At some degree the installation (latest DAHDI drivers, Asterisk 1.6.0.18 on Centos 5.x) works. I can get incoming calls to the dialplan context that is

We have an asterisk box with the following configuration: - AMD Athlon XP 2400+ - 512 MB RAM - SUSE Linux 10.1 - a Digium card TDM400P with 3 FXO - another Digium card TDM400P with 4 FXS - asterisk 1.2.7.1 - zaptel 1.2.4 I already checked that those cards aren't sharing interrupts (by cat /proc/interrupts): 0: 14119786 XT-PIC timer 1: 10 XT-PIC i8042 2:

I'm using IAXmodem and Hylafax with 'faxdetect=incoming' and things mostly work pretty well. My main lines come in via T1 DID. Today, HR got tired of having someone read and forward their faxes to them and requested we bring their physical machine back on line. I have been able to get the fax forwarded to the appropriate zap channel, but I cannot seem to get it to stop

[18884732963 at from-fax-machine:... - your call is hitting the from-fax-machine context - yet your 'fax' exten is in the from-pstn-4 context. See the "[2011-03-17 13:40:29.6] NOTICE[8825] chan_dahdi.c: Fax detected, but no fax extension" line. When Asterisk detects an incoming fax tone - it tries to automagically route the call to the 'fax' extension in the SAME

The card you installed has FXO or FXS modules in it ????? are you getting your lines directly from the telco co??? Doug D On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent: * -----Original Message----- * From: Todd Reese * Reply-to: Asterisk Users Mailing List - Non-Commercial Discussion * To: asterisk-users at lists.digium.com [3] * Subject: [asterisk-users] Dahdi

I've been going nuts lately trying to get rid of an annoying echo problem that makes my asterisk server unusable when clients try to call me. Here's the breakdown of the issue - Hoping that someone can throw me a clue: My setup is as such: Single AMD Athon machine with X100P clone card and voip through multiple providers . * Inbound calls through the X100P that do not bridge to