similar to: Disconnecting during the call, analog lines

Hi List; Asterisk does not have any kind of cards that can work with it to be used with Digital Phones (digital phones differ than analoge phone and differ than IP Phones). Anyone can advise about this as I did not find this on Diguim Regards Bilal Ghayad __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around

Hi; How can I know the duration that the DAHDI channel is still used? I need to know its status and since when it is in this status, how? Also, is it possible to hangup the channel if it has been openned more than 90 minute? Other than using the timeout in the Dial command (because this I know it). What is happening with me that from time to time, I find some DAHDI channels are stayed connected

Dears; I do not know if any had experience in using speex or ilbc with IAX and got good results, because I am facing a problem with GSM. I am facing a noise problem when I am using GSM with IAX trunk as following: IP Phone (G711) ---> Local Asterisk Box ---> IAX Trunk using GSM codec ---> Remote Asterisk Box ---> Digium Card (FXO) to terminate the call to the destination While no

Hi List; If I am configuring Diguim Analoge card, then I need to run #modprobe wctdm, but the question why I need to run #modprobe zaptel also? What #modprobe zaptel does a things that #modprobe wctdm does not do? Any help? Regards Bilal ____________________________________________________________________________________ Looking for a deal? Find great prices on flights and hotels

Dears; I am facing a problem in disconnecting the calls, it is related to the rtptimeout (disconnecting if there is no RTP packets from both sides). My Asterisk Box is behind NAT but there is a static real IP address at the ADSL router. We call from the Mobile to the PSTN analogue numbers which are connected to Asterisk Analogue card (the telephone lines are analoge), and then we dial the

Hi List; I need to do a call transfer using analoge phone connected to fxs, but I do not need this to be done using flash hook, let it to be using the # or * or any code, but how I can configure that this code is for transfer? Also, I do not need the flast hook to be used for trasfer as it cause usually a confusion to distinguish between the hangup and the call transfer. Any advise? Regards

Hi All; I do not know if anyone faced such case in dealing with open vpn (as we need it for fring to be used from the mobile: Which mobile can be used to install the open vpn client on it, so we can use it to do a vpn channel with the server that has open vpn server? Regards Bilal

Hi All; I have an E1 card with two ports for ISDN PRI. Do I need to install DAHDI in addition to LIBPRI? For placing outside calls (outgoing) via the PRI, then in the extension.exe file, I will use the Dial function? But how can I determine that I need to use the PRI channels and not the analoge channels? Last point: how can I know that asterisk is containing libpri? In other words, how can I

Hi List; I need to configure a softphone to be client and use it with Asterisk, which is the recommended one? Is it iax2? Regards Bilal ____________________________________________________________________________________ Boardwalk for $500? In 2007? Ha! Play Monopoly Here and Now (it's updated for today's economy) at Yahoo! Games.

Hi List; How can one Asterisk Box A to send a SIP call for another Asterisk Box B, and that call to be authorized based on the username and password, and not on the IP (as the IP address of the source is not known because it keep changing)? I think the trick in the Dial command, how to write it properly in a way that other Asterisk Box can recognize the sip username and password which are existed

Hi Danny; Really I did not understand how I can determine if the IO will be DB or conf files? Is it from the Asterisk manager? Regards Bilal ------------------------- It depends on how you are configured. The gui interfaces using Asterisk Manager, so you get the Same IO from the gui that you would get from a native manager session. -----Original Message----- From: asterisk-users-bounces at

Hi All; Anyone knows if there is an Asterisk version that setup can be stored in Database instead of the configuration files (.conf)? Any advise? Regards Bilal

Hi All; To overcome the echo problem, what mainly I have to do in the configuration other than the following line in the system.conf under dahdi directory? echocanceller=mg2,1-16 1) How can I know if the digium card supporting echo cancellator? 2) If I am getting a message in the consol that unable to enable the echo cancelator, then what does it means? The hardware is not supporting echo

Hi All; I tried Firefly softphone with IAX and it gave very poor quality. Any one advise a good strong softphone that can work with IAX fine? Regards Bilal ____________________________________________________________________________________ Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now. http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ

Hi; If my landline service provider does not provide the ability to send the SMS, and I need to send SMS from asterisk, then what is the required? How? Is it possible to send SMS from asterisk using SIM card to be connected via GSM adaptor connected to FXS ports? Or HOW?

Hi All; How to let the virualbox (ubuntu OS) to be able to see the digium card? Because when I install elastix or asterisk with dahdi, it is not able to see the digium card if the installation though the virualbox .. What is the solution? Regards Bilal

Hello; Is there a method "way" to be able to dial the phone number through asterisk from the outlook email contact? Regards Bilal -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20140128/17174762/attachment.html>

Hi All; Can anyone advise if using Cisco IP Phones in skinny protocol is fine or not? Or it is better to use it in SIP protocol? Regards Bilal

Hi All; Any one advise for open source prepaid billing other than A2Billing that can work with Asterisk and it is rich by features (for large business)? Regards Bilal

Hi List; If I need traffic to be directly between the endpoints, then I have to set the canreinvite = yes? If I did not configure the canrenvite at all, then by default it will pass the traffic via Asterisk and not directly between the endpoints? What if one endpoint was SIP and configured with canreinvite=yes while other endpoint was IAX2 and configured with canreinvite=yes, then they can send