similar to: carefulwrite: write() returned error: Broken pipe

Hi there noticed a strange thing in asterisk 1.6.2x 1.6.1x after one of the clients sends bye asterisk first sends invite to other side then after 200 ok it sends bye I am not sure but that could be some missconfiguration issue or a bug? so it's like this: side A sends bye to asterisk, asterisk responds with 200 OK to side A, then it sends INVITE to side B, expects 200 OK

Hi: I've searched the archives and the Internet for hours but have yet to find a way to do stacked area plots (like the kind in Excel) in R. I think that polygon may work but it would require a bit of manipulation of my data. I was hoping for an easier way. An example of what I'm trying to do can be found here: http://jcharts.sourceforge.net/samples/stackedArea.html Thanks, Josip

Hello Incoming calls from the FXO trigger an AGI script which simply NOOP data sent by Asterisk through stdin. The first two NOOP work fine, but after this, Asterisk isn't happy: ============= extensions.conf ... [from_fxo] exten => s,1,Wait(2) exten => s,n,Set(CID=${CALLERID(num)}) exten => s,n,AGI(/var/tmp/test.lua) exten => s,n,Wait(5) exten => s,n,Hangup =============

Hello List, I have been working on a little PHP software that uses AMI's UpdateConfig command in order to modify some of it's config files. I was working with 'Asterisk 1.4.22.1' and everything was working. After upgrading to 'Asterisk 1.4.23.1' I receive a lot of errors of the type: ERROR[11505]: utils.c:966 ast_carefulwrite: write() returned error: Broken pipe

Hello! If I have more than a hundred analog telephones (analog lines) that need to be connected to Asterisk PBX, what kind of hardware do I need, and where can I buy it? Thanks in advance!

Hi, I see a round of bug fixes and well as xenbus were pulled upstream. Is anything else going into .38? -- 2. That which causes joy or happiness. _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel

Hi gang, Since I'm getting no joy from device_Status or SIPPEER in 1.4.26-rc1, I thought I would do an AGI to read my hints and check for line in use that way. The AGI works fine from a prompt, but returns the dreaded "utils.c:966 ast_carefulwrite: write() returned error: Broken pipe" when I try to run it from the dialplan. Here is my dialplan snippet;

Dear R Help-Listers: I have a problem that seems like it should have a simple solution, but I've spent hours on it (and searching the r-help archives) to no avail. What I'd like to do is to generate a new variable within a data frame, the values of which are dependent upon the values of an existing variable within that data frame. Assume that I have the following data:

Hello: As someone making the move from STATA to R, I'm finding it difficult at times to perform basic tasks in R, so forgive me if I've missed an obvious and easily obtained solution to my problem. I've searched the help guides and the archives and have not been able to find a solution that works. I have a data frame with thousands of observations that looks something like this:

Hey Guys, We upgrade asterisk from 1.2.x to 1.8.2.3 and my one of agi script doesn't working We have allpage.agi script for paging system on all polycom 501 but after upgrade it broke. Any idea what is this error ? extension.conf exten => 7770,1,agi(allpage.agi) exten => 7770,2,meetme(7770,dq) exten => 7770,3,playback(beep) exten => 7770,4,hangup following is agi debug....

Hi, when I have made a decision tree with rpart, is it possible to "apply" this tree to a new set of data in order to find out the distribution of observations? Ideally I would like to plot my original tree, with the counts (at each node) of the new data. Reagards, Jay

I was playing with SASL authentication a bit today and I wasn't able to get libvirt to authenticate against PAM (or anything else except the sasldb, although I didn't try Kerberos). Does anybody know off the top of their head what mechanisms/password check options work? I'm trying to figure out if I'm attempting the impossible. Dave

Dear R users: I have run a logistic regression, used Gelman et al.'s car package to simulate the parameter estimates of that model, and have plotted the probability (using Gelman et al.'s invlogit() function) of the dependent variable being 1 given the value of a particular independent variable is at its mean. The plot has probabilities on the y-axis and the number (1-1000) of the

Dear R-Helpers: I'm having a problem getting dates into the correct format. I have a data frame, which is based on a .csv file that I imported into R via read.table. R has converted my date variables to factors; when I use the as.Date command, most of the values are converted "correctly" (and by this I guess I mean converted "as I wish them to be") but some have not been.

Hello: I've come to a dead-end in my search for a solution to a graphing problem that I am encountering. I have used xyplot (from the lattice package) successfully to plot 36 time-series plots (lines) of under-5 mortality for a set of countries in Sub-Sarahan Africa. What I would now like to do is to add vertical bands (rectangles) that correspond to time-periods during which each of the 36

Hi, Let's say that I have a set of column names that begin with the string "Xyz". How do I extract these specific columns? I tried to do the following: dataframe1[,grep("Xyz",colnames(dataframe1))] But it does not work. What is wrong with my expression?

Dear R Helpers: I have a data set where the unit of observation is country-year. I would like to generate a new data set based on some inclusionary (exclusionary) criteria. Here is an example of the type of data that I have. df<-data.frame(cbind("country"=c(rep("Angola", 9), rep("Burundi", 7), rep("Chad", 13)), "year"=c(1975:1983, 1989:1995,

Hi, I have a dataframe column from which I want to calculate the number of 1's in each entry. Some column values could, for example, be "0001001000" and "11110000111". To get the number of occurrences from a string I use this: sum(unlist(strsplit(mydata[,"my_column"], "")) == "1") However, as my data is not in string form.. How do I convert

Package: xen-hypervisor-4.1-amd64 Version: 4.1.4-3+deb7u4 Severity: critical Hi, Not sure how come I'm the first one to file this kind of a bug report :) but here goes JFTR... http://xenbits.xen.org/xsa/advisory-123.html was embargoed, but advance warning was given to several big Xen VM farms, which led to e.g. https://aws.amazon.com/premiumsupport/maintenance-2015-03/

Package: xen-utils-4.0 Version: 4.0.1-2 Hi, When you change XENCONSOLED_ARGS in /etc/default/xend, there's no normal way to apply it. Even if you do '/etc/init.d/xend stop', that doesn't stop xenconsoled, despite the fact the analogous 'start' action did start it. There isn't even a separate init script action to stop it, it has to be killed manually. Same goes for