similar to: IPKall using iax

Hi Folks, I recently setup an asterisk system in order to provide a telephone phone system for my web hosting business at a very low expense. My problem is that DTMF tones are not being recognized when calling the IPKall phone number. Calling my server via FWD and IAXTel works out fine however. Has anybody experienced this with the IPKall service? are they not passing the DTMF tones or am I doing

On Sat, 2005-06-18 at 13:17 -0700, Matthew Asham wrote: > For what it's worth I use a residential Shaw connection and have no > problems with IAX registration nor SIP to our Asterisk PBX elsewhere on > the 'net. When I had a dynapic IP connection with shaw, there was not problem either. I just changed to static and IAX can not connect. How can I test it? iax2 show registry Host

Hi all, I've got one of those cool free incoming IPKall phone numbers from www.ipkall.com. These numbers just connect to the SIP proxy of your choice, they default to Frreworld Dialup. You can use them with your own sip proxy on asterisk. My config for this is below. The trouble I'm having is the incoming calls do not seem to hit the section in sip.conf for the call. With sip

I'm loosing IAX registration after few hours and can not make call using IAX protocol, reloading configuration does not help. Internet connection stays up not a problem. When I reboot the firewall IAX goes through just fine. What to look for? -- #Joseph

Thanks for the feedback ! I know the IP-address of my Asterisk-server. The WAN-interface of my Asterisk-box is set manually (ifcfg-eth1). I have port 4569 forwarded on my NAT/firewall. Strangely I have the same 'notice' when being attached directly to the internet (so no firewall in between). And set my WAN-interface to the IP I get from my ISP or even when obtained by DHCP. Doesn't

HI I am having a problem with the new IPKall number I just got. Other sip numbers work that cost money. The problem I am having to one way audio. I can not hear the outside party when they call in. Is there something special about IPkall I'm missing?

I can't seem to change the default registration for IAX clients: Feb 6 12:22:52 NOTICE[7883]: chan_iax2.c:5673 update_registry: Restricting registration for peer 'virbiage' to 60 seconds (requested 3600) Feb 6 12:23:03 NOTICE[7883]: chan_iax2.c:5673 update_registry: Restricting registration for peer 'test1' to 60 seconds (requested 1200) Can this be controlled on a

I'm trying Asterisk 10.0 (as 8.x is not passing PSTN CallerID) and Asterisk 10.0 is no better. I'm still getting: WARNING[12295]: chan_sip.c:14446 check_auth: username mismatch, have <11>, digest has <pstn-1270> NOTICE[12295]: chan_sip.c:22769 handle_request_invite: Failed to authenticate device "KMIEC Z" <sip:7804715665 at 10.0.0.110>;tag=1c1222950155 Anybody

Does IPKALL still exist? I am after a free SIP trunk - who is still giving these away these days? As I noticed Stanaphone is no longer in business? Regards, Dean Collins Cognation Inc dean at cognation.net <mailto:dean at cognation.net> +1-212-203-4357 New York +61-2-9016-5642 (Sydney in-dial). +44-20-3129-6001 (London in-dial). -------------- next part --------------

I'm trying to setup zoiper ( formerly idefisk ) to use my asterisk server at work from home. I've setup zoiper for iax, set the ip address to work's fixed ip address, user: home, password: password but the zoiper log shows: 11:02:35 Rejected registration for 'home@<my-office-ip-address>' with cause 'facility rejected' 11:03:35 Rejected registration for

I have, in iax.conf the register statement: register => username:password@iaxtel.com This causes registration attempts to iaxtel.com for both IAX and IAX2. Every once in a while there is a packet for port 4569 keeping the IAX2 registration alive. This is fine. But, I have a barrage of registration attempts to iaxtel on port 5036 for IAX. Every UDP packet is answered with an ICMP packet

hi, i want to call PC2PC between to IAX client without authentication i want to allow every user to use PC2PC no any password required. Please let me know what i have need to do in IAX.conf or any other file to allow any user to call Pc2Pc. My IAX.conf [guest] type=user context=default callerid="Guest IAX User" My extensions.conf [default]

Hi All, I am having trouble with receiving calls from FWD via IAX. I know this isn't a FWD support forum, but I suspect the problem is my asterisk setup. The problem is that I can dial out to fwd subscribers, even myself but they can't dial me using my FWD number. I don't know much about IAX, but it would seem to me like a registration problem, but I get no errors or warnings in

In response to the postings by Andrew Kohlsmith and Ernest W. Lessenger: Andrew, I modified the exten line in extensions.conf as you suggested. Unfortunately, It still does not work... Ernest, I spent approx. 4 hours reading list archives (and anything else Google served up) on how to configure iax.conf and extensions.conf to work with Voicepulse. Then, I sent an email to voicepulse

I've asked this before but I don't recall seeing anyone respond. Maybe the answer is so simple that it should jump right out, but its not. I've got three iax connections defined, two working fine (including one to iaxtel), and one that is somewhat intermitant. If I do a cli 'iax show registry' and 'iax2 show registry' I see "both" iax and iax2

Dear Sanjay, Sorry sanjay i miss to explain completely. My PC2PC mean is Dialer2Dialer i want to allow call between Dialer with out any registry and authentication through IAX. so i need to setup Asterisk accept calls from any user and users can call to each other without any password and registration. please help how can i configure Asterisk using IAX in this regards. thanks, Asif Message: 9

hi, i want to call PC2PC between to IAX client without authentication i want to allow every user to use PC2PC no any password required. Please let me know what i have need to do in IAX.conf or any other file to allow any user to call Pc2Pc. My IAX.conf [guest] type=user context=default callerid="Guest IAX User" My extensions.conf [default] exten=>_.,1,Dial(IAX2/${EXTEN})

I'm trying to setup zoiper ( formerly idefisk ) to use my asterisk server at work from home. I've setup zoiper for iax, set the ip address to work's fixed ip address, user: home, password: password but the zoiper log shows: 11:02:35 Rejected registration for 'home at my-office-ip-address>' with cause 'facility rejected' 11:03:35 Rejected registration for

I'm trying to setup zoiper ( formerly idefisk ) to use my asterisk server at work from home. I've setup zoiper for iax, set the ip address to work's fixed ip address, user: home, password: password but the zoiper log shows: 11:02:35 Rejected registration for 'home at my-office-ip-address>' with cause 'facility rejected' 11:03:35 Rejected registration for

We have been, unsuccessful, trying to implement inter-asterisk communications using IAX. I was wondering if anyone is having similar problems, or would share information about their succes/ Our environment consists of two servers with public IP addresses and DNS entries that resolve. (for the example we use "domain.net") Based on the information available to us, we have tried the