similar to: E1 w/ TE420B EC

Hi, Running 1.4.26.1 here. I have installed TE420B card in my server, and followed the appropriate steps (as far as I know to configure it). This TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling type. When I dial out, I get this message: Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0

I have a 'CONGESTION' Status with R2 protocol. While testing this scenario sip GW--?Asterisk ?Digium E1 R2 Protocol?Cisco E1 R2 protocol?sip Gw Find below my error and configuration ,where are the errors in my configuration ? ========================================================================= Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on

Hi All, I am facing problem with E1 line. I have installed Asterisk (1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10) But every now and then I face problem of down E1's. The log show lot of entries like "pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2" This happens on a regular basis and the E1 becomes up after some time. My

Hello- After configuring DAHDI and starting asterisk, I get the following message continuously on the Asterisk console: WARNING[2057]: chan_dahdi.c:4158 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! My card is a D410P configured for E1, only the first span is configured, and configuration snippets are as follows: From /etc/dahdi/system.conf:

Dear members of the list, I have difficulties to obtain sync with a Digium TE420 PCI Express For four entries E1, In my case I am with only 3 E1s available to configure. The telephony operator is BrasilTelecom and Signaling is R2 Digital. The information I have is that are E1s with 32 channels, not have sure. My settings Have been based on the link reference:

Hi, I have a digium card (igium, Inc. Wildcard TE405P quad-span T1/E1/J1 card 5.0V (rev 02)) 4 ports I want to make a loop test between digium card E1 to test the configuration of dahdi What I want to do scenario is I connect port 1 and port4 in the digium card with E1 cable SIPcall-->E1 Digium port 1--->(Loop)E1 port 2---->sip extension local. kindly can any can help me to

Hello I've got small PBX (30 simultaneous connections) based on asterisk (1.6.2.6), which uses Stargate 2N ISDN to GSM gate. It runs ok for day or two, but then I get: dahdi: HDLC Receiver overrun on channel TE4/0/1/16 (master=TE4/0/1/16) in my kernel logs, in asterisk i get: pri show spans PRI span 1/0: Provisioned, Down, Active PRI span 3/0: Provisioned, In Alarm, Down, Active (span 3

Dear, I always had one E1 card with one span, so I've never had any problem in set it up through /etc/dahdi/sustem.conf and /etc/asterisk/chan_dahdi.conf because I put span=1. But now I have a PBX with two E1 cards with 4 span (8 span in total). How do I have to define both card in system.conf and chan_dahdi.conf, and how do I have to refer each span to the corresponding card ??? Thanks a

The card you installed has FXO or FXS modules in it ????? are you getting your lines directly from the telco co??? Doug D On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent: * -----Original Message----- * From: Todd Reese * Reply-to: Asterisk Users Mailing List - Non-Commercial Discussion * To: asterisk-users at lists.digium.com [3] * Subject: [asterisk-users] Dahdi

hello list, i have installed 2 diguim cards in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

Hi anyone have a idea for debug my digium TE405P card ? My zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone = fr defaultzone = fr My Zapata.conf: [channels] language=fr context=from-E1 switchtype = euroisdn pridialplan = unknown signalling = pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Hello I'd like to configure Asterisk so that... 1. I ring it from my cellphone with CID number displayed, just to notify Asterisk that I wish to make a call 2. Asterisk waits until I hang up, calls me back, and prompts me for the number I wish to call 3. Asterisk puts me on hold through Flash(), which is apparently the equivalent of hitting the R key on European handsets 4. Asterisk calls the

We are using AAH with Asterisk 1.2.7.1 with a TE405P as listed below. We are getting frequent restarts on the spans which lead to dropped calls. I have pasted some hopefully pertinent information below -- anyone have any clues that might help? Thanks Next line is repeated throughout messages, going through every channel in every connected span. asterisk/full.1:Apr 24 01:15:25 VERBOSE[4196]

I am having problems getting a Nicherons TDM400P wildcard clone to dial out. Everything appears to be configured correctly, but although I see call progress, it never seems to actually pick up the phone. (The following is a test of 911 emergency, where I substitute 811 [repair service] as the actual number dialed.) *CLI> -- Executing [911 at from-internal:1]

Dear All; I am afraid from IRQ misses: 1 The ISDN E1 was working fine on the machine, the electrical disconnected and then the Red Allarm. I checked the dahdi and I found that I have to reinstall dahdi again and I did. But still not becoming UP. The output of the cat /proc/dahdi/1 is following (I am afraid from the IRQ misses: 1, so if it is a problem what is the solution)? [root at CC

I just managed to put in a TE410 card in an Asterisk box to work with OnRamp 20(E1 downunder). I am able to dial in but was not able to dial out. Can anyone offer me some advice please? In my extensions.conf, I just put in: [default] ... exten => 0,1,Dial(Zap/g1) and I get this on the console when I dialled 0. -- Executing [0 at default:1] Dial("SIP/5166-b76004f8",

Hello, My first attempt to get dahdi running on 1.4.28... with a Rhino 8 port modular card and a single FXS module. Got the Rhino card installed and the machine sees it: root at pbx:/etc/dahdi# dmesg | grep rcbfx [ 71.985309] rcbfx 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 71.985440] rcbfx 1: Rhino PCI BAR0 50100000 IOMem mapped at ffffc90008d7c000 [ 71.985504]

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello List, since some days i run into the problem that one span on a TE407P is not comming up correctly. With intense debug on that span i get: < [ 02 01 7f ] < Unnumbered frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] < 0 bytes of data