Displaying 20 results from an estimated 6000 matches similar to: "DAHDI Error and poor audio quality"
2010 Jul 19
1
Problem with E1
Hi All,
I am facing problem with E1 line. I have installed Asterisk
(1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10)
But every
now and then I face problem of down E1's. The log show lot of entries like
"pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of
span 2"
This happens on a regular basis and the E1 becomes up after some
time.
My
2009 Jan 28
1
E1 conection to a Cisco2600
Hi
I am trying to connect asterisk with a Cisco GW 2600 with E1 pri using a
Digium, Inc. Wildcard TE210P dual-span T1/E1/J1 card 3.3V (rev 02),
Errors:
[Jan 28 17:32:33] VERBOSE[6182] logger.c: == Primary D-Channel on span 1
up
[Jan 28 17:32:33] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think
we're the CPE, but they think they're the CPE too.
[Jan 28 17:32:34] NOTICE[6182]
2010 Jun 16
2
DAHDI PRI error message
Hello-
After configuring DAHDI and starting asterisk, I get the following
message continuously on the Asterisk console:
WARNING[2057]: chan_dahdi.c:4158 pri_find_dchan: No D-channels
available! Using Primary channel 16 as D-channel anyway!
My card is a D410P configured for E1, only the first span is configured,
and configuration snippets are as follows:
From /etc/dahdi/system.conf:
2010 May 31
1
Suddenly "HDLC Bad FCS (8)" errors on ISDN-PRI, changed nothing
Hi fellow asterisk users,
I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel
module) an approx. 100 snom320. The whole installation is running
without issues since 5 months.
Without having changed anything on the asterisk server for at least 2
months, i noticed "clicking sounds" at external calls over the PRI.
Asterisk constantly throws the following messages:
...
2010 Apr 30
1
HDLC Receiver overrun on Wildcard TE410P
Hello
I've got small PBX (30 simultaneous connections) based on asterisk
(1.6.2.6), which uses Stargate 2N ISDN to GSM gate.
It runs ok for day or two, but then I get:
dahdi: HDLC Receiver overrun on channel TE4/0/1/16 (master=TE4/0/1/16)
in my kernel logs, in asterisk i get:
pri show spans
PRI span 1/0: Provisioned, Down, Active
PRI span 3/0: Provisioned, In Alarm, Down, Active
(span 3
2009 Dec 22
2
E1 R2 Congestion Status
I have a 'CONGESTION' Status with R2 protocol.
While testing this scenario sip GW--?Asterisk ?Digium E1 R2
Protocol?Cisco E1 R2 protocol?sip Gw
Find below my error and configuration ,where are the errors in my
configuration ?
=========================================================================
Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on
2013 Feb 26
0
activation round-robin
hello list
i have installed 2 diguim card in my server using asterisk 1.4 (i use the
old version with zapata.conf and zaptel.conf)
i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i
want to active the round-robin for span 2 and 6) in order to activate the
WIMAX and FH
please see the configuration below and tell me if there is anything wrong
question 2: what is
2013 Mar 21
2
Need help about round-robin
hello list,
i have installed 2 diguim cards in my server using asterisk 1.4 (i use the
old version with zapata.conf and zaptel.conf)
i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i
want to active the round-robin for span 2 and 6) in order to activate the
WIMAX and FH
please see the configuration below and tell me if there is anything wrong
question 2: what is
2005 Jan 04
1
HDLC Bad FCS (8) HDLC Abort on TE410P
Dear All,
we have installed a TE410P card on a Dell Poweredge 1750 running a slackware
10 with 2.4.26 Kernel. Then we have made two loops on the card and we have
configurated all the 120 channels. Our goals was to perform some stess tests
even if in this scenario we used the same box as generator and target.
The stress test comprised to generate up to 60 calls at the same time by
placing a file
2013 Jun 28
0
No subject
fact I'm surprised that's changed (FreePBX's DAHDI module created the
current config -- i.e. the one I posted in my original email). I'll
change that back and see if that makes a difference, but I'm pretty
sure I used the above configuration in a previous attempt with the
same results.
Also, I have indeed received the following messages prior to the
interface going down and
2010 Jun 12
2
Qwest PRIs
Hi,
I'm trying to bring up two PRIs from qwest with asterisk and dahdi. I'm
using an OpenVox D410E and the drivers are loaded. My system.conf looks
like this:
# Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" B8ZS/ESF RED
span=1,2,0,esf,b8zs
bchan=1-24
# Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" (MASTER) B8ZS/ESF RED
span=2,1,0,esf,b8zs
bchan=25-47
dchan=48
These
2011 Aug 16
1
PRI Problem
I am having a problem with a new PRI turn-up on dahdi 2.5.0 and
asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS,
ESF and the span shows up and ok. This PRI is merely a crossover T1
going into an old DC0 class 5 switch.
I am getting the following errors over and over again
[Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043
my_handle_dchan_exception: PRI got event: HDLC Bad FCS
2009 Aug 24
1
E1 w/ TE420B EC
I keep getting a red alarm when trying to setup asterisk to use my
TE420B EC. I only have a blank context setup in my extensions.conf as
I haven't started to config that until I can clear this red alarm. I
don't have physical access to the server, so I can't go reseat the
modules/card/ethernet cable, though I have hands on location that have
done this a couple times
2010 Jul 06
0
Problem with wct4xxp - cannot make calls
Hi,
I'm having problems with a TE420P card, in which I cannot make calls
using spans 2 through 4.
After a couple of days of working correctly, spans 2, 3 and 4 start
failing (can not make calls). The system is configured to work with SS7.
After the ACM message goes out, immediately a REL message is returned.
I searched for error messages in /var/log/messages and could not find a
clue
2006 Apr 30
2
PRI Issue: D-Channel woes
Hi,
I am about to pull my hair out after trying to get our PRI up and working.
We are switching from a Cisco gateway to an Asterisk box which provides
the 23 phone lines for our office. So, because the Cisco gateway is
working I can assume I have all the settings right (b8zs, esf, dms100,
etc) and the PRI is live (because we are switching over). When dialing
from PSTN, I get busy signal. When
2009 Mar 17
0
Weird issue with outbound calls and MOH
Hi,
We have a PRI Trunk (physical E1) and we are getting
some rather weird and very isolocated problems. On outbound calls to
specific numbers, it would seem to me that DTMF from the remote side is
affecting the local asterisk system. Basically what happens:
- We make a OUTBOUND call via the PSTN (PRI Trunk) to a remote System
- Remote Answers, and converse
- Remote sends DTMF on their site to
2010 Dec 16
1
PTMP BRI Unable to receive TEI from network in state 2(Assign awaiting TEI) - Asterisk 1.6.2, Latest DAHDI, LibPRI
Hi all,
Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with
Asterisk 1.6.2 and DAHDI BRI - to no avail.
I had two servers so copied network setting etc from the working one,
moved the card across, ran dahdi_genconf etc and it didn't work.
Here's the console output with notices disabled:
lucas*CLI> pri intense debug span 1
Enabled debugging on span 1
[Dec 16
2010 Jun 11
1
HDLC Bad FCS (8) on Primary D-channel
Hello,
I've got a running system in which logs are full of messages such as:
[Jun 10 07:24:14] NOTICE[2414] chan_dahdi.c: PRI got event: HDLC Bad FCS (8)
on Primary D-channel of span 2
The strange thing is those messages are coming from a single span.
My setup is :
Asterisk 1.6.1.18
Junghanns OctoBRI
with wcb4xxp driver
libpri 1.4.10.2
dahdi 2.3.0
3 BRI lines in PtMP mode
What does this
2010 Nov 27
1
DAHDI 2.4.0 produces HDLC errors with echo canceler
Hi,
After upgrading to DAHDI 2.4.0 from Zaptel, I noticed a lot of HDLC
errors on my console:
[Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Bad
FCS (8) on Primary D-channel of span 1
[Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Abort
(6) on Primary D-channel of span 1
These errors prevented calls from being made and received on my PRI spans.
This seems
2009 Dec 04
1
DAHDI issues on 1.4.26.1
Hi,
Running 1.4.26.1 here. I have installed TE420B card in my server, and
followed the appropriate steps (as far as I know to configure it). This
TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling
type.
When I dial out, I get this message:
Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to
create channel of type 'DAHDI' (cause 0