similar to: Trouble with originating a call through Asterisk Manager Interface

Hi all, I must admit that I am stuck. I have a TDM400P card with two FXS and two FXO modules which I had set up and configured so that it was working beautifully. The only problem was that occasionally it would get itself into a state where outgoing calls would simply be met with a very loud static. A reboot would fix this issue and everything would work fine for a while. Recently however,

Hello, my configuration is the following: a TDM400P board with an fxs and fxo daughter boards on it. I thus connect a fax to my FXS port, after having verified that this port was correctly functioning. For this, I had tried before with a simple phone, and with some basic voicemail exten scripts. Here is my simple dialplan for my fax reception: exten => 300,1,Ringing() exten =>

I have the following in my extensions.conf [ext-local] exten => _53XX,1,Wait(2) exten => _53XX,2,NoOp,Dialing ${EXTEN} from ext-local-custom exten => _53XX,3,Macro(dialout-trunk,2,${EXTEN},,) This is used to match inbound caller-id for my legacy PBX. It works fine for inbound calls, but not for internal SIP calls. If I call from a SIP phone that is also in [ext-local], it looks like it

Hi Folks, I'm trying to use my mobile as a trunk via bluetooth - calls done in a softphone go thru GSM network and calls destinated to my mobile are answered at the softphone. I have asterisk configured to do so but I'm facing an issue - Audio is audible but it?s not intelligible. I feel like the audio is breaking. Below is the asterisk log. I also get lots of ?hci_scodata_packet: hci0

Hi, I'm having problems with the voicemail, the app keeps exiting in 3-5 seconds. Any considerations will be appreciated. Thanks, D.K. Debug messages: Apr 18 20:53:41 DEBUG[26150] pbx.c: Launching 'Goto' Apr 18 20:53:41 DEBUG[26150] pbx.c: Launching 'VoiceMail' Apr 18 20:53:41 DEBUG[26129] chan_sip.c: Checking device state for peer XXX Apr 18 20:53:41 DEBUG[26129]

Hi, sorry for the long debug output below. I configured Asterisk with AMP to send the whole number including the extensions of the callers to the called party. Whatever I configure in AMP it looks like it is used, In my eyes it is ok, but doesn't seem to work. 033811234451 is the call id i configured, and it seems to use them, but the caller will only see a 0338189040 instead of my

Hello Gentleman, I'm new to asterisk, this is my first instalation, first post... so I'd like to apologize if this question has already been made. I googled but I couldn't find nothing similar. Here's the thing. I'm migrating from ATA to Asterisk one of my client's office and I have a very simple setup. A Linux PC running Debian Lenny + Asterisk 1.4.21. It's a

Hi All, I am trying to get the opus codec working with linphone. I followed the instructions... This shows me its loaded core show translation paths opus --- Translation paths SRC Codec "opus" sample rate 48000 --- opus:48000 To g723:8000 : No Translation Path opus:48000 To ulaw:8000 : (opus at 48000)->(slin at 48000 )->(slin at

Hello people, I've ran into two problem that I can't seem to be able to solve on my own. Here's my scenario (running Asterisk 13.28.1): In short: - Asterisk behaves unexpectedly (at least to me) when negotiating between endpoints             that have a different but intersecting set of codecs (preventing direct media flow).           - Also, when an endpoint sends RTP with an

Just checking the transcoding on our Asterisk boxes and I get the following results. I have the g726, ilbc and lpc10 formats and codecs enabled in 'make menuselect' so I dont understand why its showing as no translation path. Any ideas? I am running certified-asterisk-11.2-cert2 Thanks Gareth > core show translation paths alaw --- Translation paths SRC Codec "alaw"

Hi, I am running a build of asterisk@home with asterisk 1.2beta1 and am trying to diagnose RxFax with a Voip incoming trunk. I am running the latest spandsp and rxfax with libtiff 3.7. Switching on debug IU can see the call come in, but after a small time the fax connection drops and the sending fax (paper doc ) has not moved in the machine. I guess it must be dropping in the negotiation

I installed a hardware g729 codec card in my asterisk, and I'm getting the following error when calling from a g729 sip extension to a SIP trunk also set to g729. The call goes through just fine, but these error messages keep flying by until I disconnect the call. Any ideas? ERROR[11871]: channel.c:1316 queue_frame_to_spies: Translation to slin failed, dropping frame for spies Jun 5

Good afternoon list. I am experiencing a problem with the CDR and callfiles. What is happening is this: When generating a call with a callfile, everything works perfectly, but the CDR is recorded in the table when they answer the call destination. The field disposition is being recorded correctly, but the duration field is marked with the ring time and billsec is marked with 0. This just happens

Dear all, I'm trying to use ulaw and alaw with Diax and Asterisk but I'm not able to, I got the following error message: Mar 20 11:47:59 NOTICE[7099]: chan_iax2.c:6350 socket_read: Rejected connect attempt from 192.168.0.55, requested/capability 0x8/0xc incompatible with our capability 0xfe02. I do not understand why because my Asterisk box load these codecs properly! Does somebody

I have no speex translation ulaw alaw gsm g726 g726aal2 adpcm slin8 slin12 slin16 slin24 slin32 slin44 slin48 slin96 slin192 lpc10 ilbc g722 testlaw ulaw - 9150 15000 15000 15000 15000 9000 17000 17000 17000 17000 17000 17000 17000 17000 15000 15000 17250 15000 alaw 9150 - 15000 15000 15000 15000 9000 17000 17000 17000 17000 17000 17000

So the call used Alaw as Codec. > Am 13.06.2020 um 17:23 schrieb Luca Bertoncello <lucabert at lucabert.de>: > > Am 13.06.2020 um 13:47 schrieb Michael Keuter: > > Hi > >> Try "sip show peer <peername>" for a phone. > > So: > > mobile phone: > bpi*CLI> sip show peer 0049177xxxxxxx > > > > > * Name :

On Saturday 13 June 2020 at 17:23:14, Luca Bertoncello wrote: > Am 13.06.2020 um 13:47 schrieb Michael Keuter: > > > Try "sip show peer <peername>" for a phone. > bpi*CLI> sip show peer 0049177xxxxxxx > Codecs : > (alaw|ulaw|ilbc|g729|g723|gsm|amr|amrwb|g726|g726aal2|adpcm|slin|slin|slin| >

Am 13.06.2020 um 13:47 schrieb Michael Keuter: Hi > Try "sip show peer <peername>" for a phone. So: mobile phone: bpi*CLI> sip show peer 0049177xxxxxxx * Name : 0049177xxxxxxx Description : Secret : <Set> MD5Secret : <Not set> Remote Secret: <Not set> Context : default Record On feature : automon

Hi all! Asterisk 13.1.0 Ubuntu 16.04, all latest. Can anybody explain this to me - I run Originate command from dialplan: same => n,Originate(Local/${number}@mycontext,app,ConfBridge,${confnum}) and I get crazy sound distortion in the conference, and I see that transcoding takes place here: NativeFormats: (slin192) WriteFormat: slin ReadFormat: slin192 WriteTranscode: Yes (slin

Again - when Originate is run from dialplan, i get: NativeFormats: (slin192) WriteFormat: slin ReadFormat: slin192 WriteTranscode: Yes (slin at 8000)->(slin at 192000) ReadTranscode: No When it's made with a call file (no matter how a call file is created), I see NativeFormats: (slin) WriteFormat: slin ReadFormat: slin WriteTranscode: No ReadTranscode: No Please