similar to: Rhino analog cards

Hello, My first attempt to get dahdi running on 1.4.28... with a Rhino 8 port modular card and a single FXS module. Got the Rhino card installed and the machine sees it: root at pbx:/etc/dahdi# dmesg | grep rcbfx [ 71.985309] rcbfx 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 71.985440] rcbfx 1: Rhino PCI BAR0 50100000 IOMem mapped at ffffc90008d7c000 [ 71.985504]

Hi All, I have a lab setup with two asterisk servers and a MAX TNT in the middle like this: asterisk sip >< sip TNT pri >< pri asterisk The TNT is running 11.0.6 and the asterisk servers are running 1.2.9.1. I can get calls to pass from asterisk sip to tnt to pri to asterisk but not the other way. The call from asterisk to pri to tnt is good, the TNT is passing SIP invite to the

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

Hello everyone, I have a Atcom AX-1600P(1) card with a FXO module and I can't configure it. I have four extension with this PJSIP settings: --- /etc/asterisk/pjsip.conf --- [transport-udp] type=transport protocol=udp bind=0.0.0.0 [6001] type=endpoint transport=transport-udp context=from-internal disallow=all allow=ulaw auth=6001 aors=6001 direct_media=no rtp_symmetric=yes force_rport=yes

Hi, I am thinking about getting some of these phones to use with my Asterisk system.. So I would be interested to hear from the people who have tired and tested these phones.. What is the voice quality like using alaw/ulaw or G.729?? Are there any problems getting them to play nicely with Asterisk?? How sturdy is the construction (reciever, handset, buttons, cable connections, etc..) ?? How

> > hi, > > How good or bad is the EC in Asterisk? > > Can anyone prove that it works at all and what it's limitations are? > > I ask cause I have some problems with this myself which variate from > call to call, and I see from others that Echo Cancel is a quite common > topic. > > Jan > > I have installed systems that had absolutely no echo

I'm having an unusual problem at one of my branch offices. Every now and then they will make a call and the person they call is unable to hear them, but they are able to hear the person. The Asterisk server has only one ethernet interface and is on the same physical network as the 2 snom 300 phones and is connected to the PSTN lines with a Rhino R4FXO-EC card. Usually hanging up and

FYI Arnaud ---------- Forwarded message ---------- From: Silvino Benevides Magalhaes <sbm2yk at gmail.com> Date: 2009/10/14 Subject: Re: about solis and rhino To: Arnaud Quette <aquette.dev at gmail.com> Hi Arnaud, I was on holiday, so I only answer you now. About rhino, I received a document contains the its protocol and a little box with rhino firmware to testing driver

Hello there, Offending source code is ????? if(? ( BattVoltage> 129 ) || ( BattVoltage < 144 ) ) Maybe swap || for && would be better. This problem I found by using cppcheck. It said [rhino.c:190]: (warning) Logical disjunction always evaluates to true: BattVoltage> 129 || BattVoltage < 144. Regards David Binderman

Hello I have an interesting situaltion and not sure if I am doing something wrong or it is a BUG. I Installed Rhino Channel on T1 line and connected Analog Phone on Rhino's Zap Channels. When I pickup analog phone and hangup without dialing any number , I am getting extra ring after hangup and if I dial any digit than there is no ring on Analog phone after hangup. Log's looks like this

Has anyone had any success with the Rhino CB-24? I can't get mine to work, I tried all the obvious settings. The cb-24 gets stuck at init ESF framing, as if it's not seeing the t1 card at all. It does get a t1 carrier (detecting voltage??) Help! Thanks.. Everything appears to look good on the server, I did: [zaptel.conf] span=1,0,0,esf,b8zs fxogs=1-24 [zapata.conf] signalling=fxo_gs

Anyone have any experience with the Rhino T1 channel bank? It looks very cost effective at around $1300 for 24 lines but I haven't seen it mentioned on the Asterisk list yet.

Hi, Does anyone know whether faxes work good when they're connectected to a channelbank ? regards, Leon

Anyone ever experience noise instead of a dial tone. We are using a Digium TE410P and 2 units of Rhino FXO & FXS Channel Bank. Everything works well when they are freshly turned on or rebooted, but after a while there's only noise can be heard instead of dial tone. Does this have anything to do with the timing configuration? Where is this time is generated from, is it from the TE410P card?

Hello list, I have recently deployed Asterisk as the phone system for my office. So far, everything has been going really well, except for one little thorn in my side. I have a set of 6 analog lines that are connected to a TE411P via a Rhino FXO Channel bank. If I call the analog number, Asterisk answers the call, and routes it appropriately. The problem is, when I hangup, Asterisk never

Just saw these new Asterisk compatible cards at Rhino's homepage. Anyone has experience with these babes? http://www.rhinoequipment.com/index.html http://www.rhinoequipment.com/t1card.html The 4-port FXO looks interesting. Looks like a very clean design. Leo

Hi Folks, Struggling with a new * installation with 2 Rhino R2T1 cards. For some reason, the system is locking up tight when you run ztcfg to configure the card(s). Configuration is asterisk 1.2.14, zaptel 1.2.12, and rhino's 1.05rxt1 drivers. The cards seem to load fine with a "modprobe rxt1", but once you run "ztcfg -vvv", the system will lock up within a few seconds, no

hello guys... well as my first post i want to say when i try to install rhino it says: ...The installer requires Windows installer 3.0 or newer... so when i try to download that (as a last resort [Wink] ) it fails... so if anyone can help thats great but if not... well this thread is mainly an error report... Thanks! Trey.

The if() statement always evaluated to true. Detected by "cppcheck", not tested on real hardware. Signed-off-by: Thomas Jarosch <thomas.jarosch at intra2net.com> --- drivers/rhino.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-) diff --git a/drivers/rhino.c b/drivers/rhino.c index ca66169..e478bcb 100644 --- a/drivers/rhino.c +++ b/drivers/rhino.c @@ -187,7 +187,7

I am testing analog phone and fax machine plugged into Rhino Channel Bank which is connected to TE412P card. This site is in China. I am running RHEL 5, Asterisk 1.4.21.2, Zaptel 1.4.11 and libpri 1.4.4 I ran into a problem which is analog phone can hear dial tone and can make outgoing calls. Another phone (ether internal or external) can call the analog phone ***but the phone does not