similar to: [Atcom] Asterisk + LAMP on 128MB RAM?

Anyone here used these phones? I'm getting more and more frustrated by todays modern crop of routers with their so-called SIP ALGs which are invariably broken, or routers with built-in ATAs which block internal SIP phones from working, so looking to use IAX for some end-users. I already support it for people who want to use (eg) Zoiper and use IAX a lot to plumb boxes together, but never

Hello According to this article, this nice little unit can only use the PSTN port for outgoing calls (ie. as a backup in case the connection to the VoIP provider stops working), but not incoming calls: http://tinyurl.com/mwjmo8 Can someone confirm that Atcom made this strange decision, and that there's no work-around? Thank you.

Hello All We purchased *25* new AtCom AT- 530 phones. Four of them did not work for even once and some of them lost configuration after some days. I talked to AT Com people over chat for support. They have just 1-2 people for support who are also busy in some other activities due to which they are unable to communicate in proper way. Often support guy left conversation suddenly and is unavailable

Hello For customers who need a small IP PBX to handle up to four ISDN lines (in France, so I guess that means EuroISDN) instead of a PC + Asterisk and an ISDN gateway box, has someone already played with the Atcom IP-4B? www.atcom.cn/IP-BRIM.html Any feedback appreciated.

Hi folks A common wisdom here is that one should use a proper hardware phone rather that an extra software on the user's PC. Why is that such a big issue? One thing that bothers me with the current crop of hardware SIP phones is that they are hopelessly properitary. So what would it take to build a fully-adaptable phone? Here are some of my thoughts. This is not anything I plan to do soon

Hello all ! Does anyone have a document describing jumpers, DIP switches, and connectors on Atcom's AX-4S (HFC-4S based 4xBRI) and AX-1E (HFC-1E based 1xPRI) cards ? Got the cards without any documents, there is nothing on a subject on Atcom's site, and so far no one from their support is replying to my emails. Thanks very much. Cheers, Nenad -------------- next part

For those of you who may be interest.... IAX2 loads are now available for the standard builds... http://www.aredfox.com/edownloadsiax2.htm Just a word of caution... Remember to change the ports over to 4569 from whatever. And don't forget to grab the palmtool from http://www.aredfox.com/download/tools/PalmTool.zip My own testing of IAX2 with both a phone and an ATA is that IAX2 is

Hi, I have a few of Atcom AT320 phones. I can choose if install SIP or IAX2 firmware. Any suggestion? Mimmus

Hello everyone, I want to build an Asterisk Box where i need 8 FXS interfaces to connect 8 phones to. The problem is, that there is only one PCI slot available. What i have is 4 USBs 2.0 interfaces free (if this helps). So here's my question: how am i going to do this? i tried to find any PCI cards supporting 8 FXS interfaces, but without success. does anyone know such hardware? Thanks in

Is the Sipura 3000 the only way to interface a remote pstn line and connect incoming calls to Asterisk? I have a location connected by network that has a phone line, when the room is occupied I want the line ti ring there as normal, but when the employee is travelling I want the line to be conencted to a ATA that then feeds it as an incoming pstn line to the pbx located at my office so it can

Hi all. We have Snom phones which do have a defined key in order to drop incoming call WITHOUT answering. Pressing that key, a "SIP/2.0 486 Busy Here" message is sent back. We have other phones (I.E. DECT Siemens C450IP, or ATCOM 320 or other) which DO NOT have any key to do that (or the key does not work, as is with Siemens C450 IP ): you have to answer and immediatly after hangup the

I've gotten nothing from http://bbs.atcom.cn on this so far. Perhaps someone on the list has experience with this. Is there a way to get MWI support for PA168V-based ATAs? Apparently some IP phones based on the PA168V chip has this support already (Atcom AT-320 for example) by configuring Asterisk with 'mailboxdetails=yes' in iax.conf. On my ATA, however, it does nothing. Any

Hi All; Till now I am not able to find a good IAX IP Phone or Gateway that can be used with good quality. Anyone can advise for good one? Regards Bilal ____________________________________________________________________________________ You rock. That's why Blockbuster's offering you one month of Blockbuster Total Access, No Cost.

I'm looking for an ATA\Voice Gateway that runs IAX and has several ports (8 would be nice). I am looking to avoid devices that use the same firmware as the ATCOM devices as I found them to be buggy (and a PITA to find the proper update). ---------- Mike Hammett Intelligent Computing Solutions http://www.ics-il.com -------------- next part -------------- An HTML attachment was scrubbed...

Does anyone know why when calling out with an ATCOM AG-188 registered with IAX (haven't tried SIP), there is no ring. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070222/a4f29a97/attachment.htm

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Does anyone have any recommendations on an IAX Desktop Telephone or ATA Device. I currently have 2 of the SIPURA-841's on my local network and now I am wanting to try an IAX Device at my remote office since I think that it would be easier to configure through various routers than a SIP Device. I just started to look at the Digium IAXy Single FXS

I'm running asterisk stable 1.0.5 and I'm trying to get the netweb eezee phone version v1.37.008 to talk IAX to asterisk. The pages I saw in the wiki maybe didn't hold my hand quite enough and the information on the eezee phone website appears to be for a different firmware version. If anyone has done this recently and has a working situation I would appreciate some useful hints

Hi All; Anyone knows an IAX IP Phone works fine and tested? Does polycom support IAX IP Phone? Regards Bilal

Hi All; Anyone can advise for a good IP Phone that has the ability to support SIP firmware and IAX firmware? Ofcourse, SIP there is a lot, but we need also the ability to use IAX (as it is good for NAT). Any advise. Regards Bilal ____________________________________________________________________________________ Looking for last minute shopping deals? Find them fast with Yahoo!

Hi: i am surveying ip phones for our company. we will use them with asterisk. we have office in taiwan, hong kong,singapore and china. cisco and polycom are too expensive for us. we try several china brand ip phones. they are all cheap and some of them have good quality. but most of them won't offer future firmware support, which we think it's important for ip phones.