similar to: asterisk crash on DAHDI error: No more room in scheduler

We are using AAH with Asterisk 1.2.7.1 with a TE405P as listed below. We are getting frequent restarts on the spans which lead to dropped calls. I have pasted some hopefully pertinent information below -- anyone have any clues that might help? Thanks Next line is repeated throughout messages, going through every channel in every connected span. asterisk/full.1:Apr 24 01:15:25 VERBOSE[4196]

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Dear, I always had one E1 card with one span, so I've never had any problem in set it up through /etc/dahdi/sustem.conf and /etc/asterisk/chan_dahdi.conf because I put span=1. But now I have a PBX with two E1 cards with 4 span (8 span in total). How do I have to define both card in system.conf and chan_dahdi.conf, and how do I have to refer each span to the corresponding card ??? Thanks a

hi folks. recently some of our customers complained about bad voice quality on the phone system. i looked at the logs and found a lot of these: [2012-11-03 08:26:38] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:45] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:54] NOTICE[11305]

Hi, Running 1.4.26.1 here. I have installed TE420B card in my server, and followed the appropriate steps (as far as I know to configure it). This TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling type. When I dial out, I get this message: Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0

Hello- After configuring DAHDI and starting asterisk, I get the following message continuously on the Asterisk console: WARNING[2057]: chan_dahdi.c:4158 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! My card is a D410P configured for E1, only the first span is configured, and configuration snippets are as follows: From /etc/dahdi/system.conf:

Hi, I have a digium card (igium, Inc. Wildcard TE405P quad-span T1/E1/J1 card 5.0V (rev 02)) 4 ports I want to make a loop test between digium card E1 to test the configuration of dahdi What I want to do scenario is I connect port 1 and port4 in the digium card with E1 cable SIPcall-->E1 Digium port 1--->(Loop)E1 port 2---->sip extension local. kindly can any can help me to

Hi, I running into the following problem on my Asterisk setup: --snip-- [Sep 3 01:40:59] NOTICE[9170] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 3 [Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: No more room in scheduler [Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: Asked to delete sched id -1??? [Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: No more room in scheduler [Sep

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

I have a 'CONGESTION' Status with R2 protocol. While testing this scenario sip GW--?Asterisk ?Digium E1 R2 Protocol?Cisco E1 R2 protocol?sip Gw Find below my error and configuration ,where are the errors in my configuration ? ========================================================================= Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on

On Sat, Jan 17, 2015 at 09:31:33AM +0100, Bertrand LUPART - Linkeo.com wrote: > >>> However, dahdi_genconf keeps finding no span: > >>> What am i missing? > >> > >> It looks like your driver is loaded correctly. My guess would be maybe > >> the dahdi-tools is packaged as an older version that doesn't know > >> about the newer te435

I'm trying to get a Qwest PRI configured and working with my lab Asterisk server. They said that the switchtype is 5ess and the signaling is pri_cpe. My entries into zaptel.conf are: span=1,0,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone=us channels=1-23 And my entries in zapata.conf are: language=en context=telco-incoming switchtype=5ess signalling=pri_cpe

Hi All, I am facing problem with E1 line. I have installed Asterisk (1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10) But every now and then I face problem of down E1's. The log show lot of entries like "pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2" This happens on a regular basis and the E1 becomes up after some time. My

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

hello list, i have installed 2 diguim cards in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Hi list! We currently have a PRI gateway composed by a box with two Digium quad-span PRI cards (a TE420 and a ). One of the cards is filled with TELCO1, while the other has first two slots filled with TELCO2, and 3rd slot with TELCO3. I am currently having (timer ?) issues on TELCO3 (span 7) D-Chan (202 as determined by dahdi_genconf ) is constantly failing causing on-going calls to terminate.

Hello I've got small PBX (30 simultaneous connections) based on asterisk (1.6.2.6), which uses Stargate 2N ISDN to GSM gate. It runs ok for day or two, but then I get: dahdi: HDLC Receiver overrun on channel TE4/0/1/16 (master=TE4/0/1/16) in my kernel logs, in asterisk i get: pri show spans PRI span 1/0: Provisioned, Down, Active PRI span 3/0: Provisioned, In Alarm, Down, Active (span 3

I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2 I've got a 2 port T2XXP card attached with on T1 currently plugged in. Inbound calls work fine, but outbound fail with the rather cryptic: [May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) There are similar threads I've found on the

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to