similar to: Softphone question

I was looking at the aastra 9133i, however I was informed that this phone is no longer supported. What are good phones around the $100 - $125 price point? (Need POE) Thanks, David Ruggles CCNA MCSE (NT) CNA A+ Network Engineer Safe Data, Inc. (910) 285-7200 david at safedatausa.com

The subject pretty much says it all. Does Asterisk support DNIS, and if so, what kind of connection is required? (T1, PRI) I've got a wink start T1. I've read comments that say the DNIS will be seen as an extension, but I'm seeing each digit of the DNIS as a separate extension. So in my case I send DNIS of 12345, Asterisk will jump from extension 1 to extension 2 to extension 3 to

Hello, I would like to double check what Echo Cancellation my Digium Card uses. I thought I bought the little more expensive card that integrates EchoCancellation. How can I check? root at sn1:~# zaptel_hardware pci:0000:0b:08.0 wcte12xp+ d161:8000 Wildcard TE121 root at sn1:~# ztcfg -v Zaptel Version: SVN-branch-1.4-r4309 Echo Canceller: MG2 Is MG2 the correct one that I am supposed

Hi, I just got a Xorcom Astribank with 8 FXS but it does not work. So I tried resetting and loading the firmware. But loading just times out. /usr/share/zaptel/xpp_fxloader usb --------- FIRMWARE LOADING: (usb) [1 devices] 'xpp_fxloader'[11561]: USB Firmware /usr/share/zaptel/USB_FW.hex into /dev/bus/usb/002/003

I'm reading voip-info.org http://www.voip-info.org/wiki-Asterisk+cdr+mysql Sorry if this is a dumb question, but: It says I need mysql and mysql-devel to compile cdr_mysql, but I don't want mysql on my asterisk box I want to connect to a remote mysql server. Can I use mysqlclient and mysqlclient-devel? Thanks, David Ruggles CCNA MCSE (NT) CNA A+ Network Engineer Safe Data, Inc. (910)

Is there any way to use Festival from script called by the ExternalIVR() dialplan function? Thanks, David Ruggles CCNA MCSE (NT) CNA A+ Network Engineer Safe Data, Inc. (910) 285-7200 david@safedatausa.com

I've got a weird problem: I've added a new phone and "sip show peers" shows a status of "OK (x ms)" but when I dial it I get "status is 'UNKNOWN'" Any help on how to troubleshoot this? Thanks, David Ruggles CCNA MCSE (NT) CNA A+ Network Engineer Safe Data, Inc. (910) 285-7200 david at safedatausa.com

I've done some googling and searched voip-info but I'm not able to find a good answer about how to provision the GXP 2000. Based on questions I've asked before it seems like a lot of people are using the grandstream phones so I figure provisioning can't be that hard. Is everyone using the web interface for *every* phone? Or is there a better, more automatic, way? TIA!!! Thanks,

First, I didn't realize I hijacked another thread! Please accept my apologies. Now the problem: Asterisk isn't compiling chan_zap. chan_zap also doesn't appear in the list of channels when you "make menuconfig" I have read all the replies and specifically Cosmin's and Tzafrir's emails. zaptel.h is located in /usr/include/zaptel I also tried "./configure

Hello, I played with the externalIVR application. So far I am able to read digits and play sound files. But how can I leave the application and continue in the dialplan so that I can execute other actions like going to voicemail, or ringing users etc.... Best regards, Lo?c. -- Lo?c DIDELOT MIXvoip S.a. Tel: +352 20 3333 20 Fax: +352 20 3333 90 ldidelot at mixvoip.com http://www.mixvoip.com

I've got IAX2 setup between two servers with this config: I have two servers on a switch: asteriskm is 192.168.0.160 and asterisk1 is 192.168.0.161 asteriskm has a Sangoma T1 card in it. I want to route calls from asteriskm to asterisk1 which will run an AGI IVR for the call. Config is below, but my problem is that 90-95% of the time when I start asterisk on the two servers I get the

Need some help with IAX trunking. I've got six systems: AsteriskM (main) ___________________|____________________ | | | | | Asterisk1 Asterisk2 Asterisk3 Asterisk4 Asterisk5 AsteriskM has two Sangoma A102 2 Port T1 cards in it, the other Asterisk boxes are using ztdummy for timing, they are all using IAX trunking. My calls come in

I finally got my X100P working and now I have a question. I have several Skutch phone line simulators. My X100P works as expected with both a POTS line and an analog PBX port, but when I use a phone line simulator it doesn't answer the line. The phone line simulator doesn't power the line until the phone set goes offhook. Asterisk shows the RED alarm and then the alarm clearing but never

I just got a brand new A101 and am trying to install it in my test Asterisk box. The install went without a hitch. I followed the directions on the Sangoma Wiki: Wanpipe Asterisk Install http://sangoma.editme.com/wanpipe-linux-asterisk-install Wanpipe for Asterisk Configuration http://sangoma.editme.com/wanpipe-asterisk-configure It went perfect, no problems and Asterisk came up fine. I downed

I'm working on writing some test IVR code in AGI. I can't get my FXO port to detect a hang-up, but I'm going to deploying this using Digital cards so I decided to just skip that problem for now. However this leaves me with a question. How does AGI detect a hang-up if everything is operating normally? TIA!! Thanks, David Ruggles CCNA MCSE (NT) CNA A+ Network Engineer Safe Data, Inc.

I installed a Sangoma card with the default install. I'm getting five digits of DNIS with each call. The T1 is setup ESF/B8ZS wink start. Each of the digits of the DNIS are being used for extensions in the context. I need a single extension that let me start an AGI script that can use the dnis. Can anyone point me in the right direction to do this? Thanks, David Ruggles CCNA MCSE (NT) CNA

I have written a script that is executed using ExternalIVR(). I am running in to performance issues when I have four or more simultaneous calls running this script. I'm running on a P4 2.8 with 512M, all calls are GSM coming in over IAX from an asterisk box that acts as a switch and handles all PSTN interfaces. My question are these: Are there ways of optimizing ExternalIVRs? (maybe

I've opened a few bugs on ExternalIVR and added patches. The biggest issue is: https://issues.asterisk.org/view.php?id=16174 [patch] ExternalIVR does not handle arguments in a consistant manner Basically, this optimizes and fixes several different ways of calling ExternalIVR. If there is anyone who is using ExternalIVR today and/or is willing to test these patches I would appreciate the

Hi, I noticed that my hint priority stops working when I add to many extensions/channels. It looks like everything exceeding 80 characters is discarded. By stop working I mean the status is and stays "Unavailable". This works exten => *1,hint,SIP/loicvoip1_1&IAX2/loicvoip1_1&SIP/loicvoip1_1_a1 This does not work: exten =>

Hello, I recently got a problem I have never seen during my previous installations. I have a Xorcom device with 4 BRI and 8 FXS ports. I use ubuntu Linux and asterisk 1.4.22. Everything works fine but after some time zap channels disappear in asterisk. root at pbx1:~# cat /proc/zaptel/* Span 1: XBUS-00/XPD-00 "Xorcom XPD #00/00: BRI_TE" AMI/CCS NOTOPEN 1 XPP_BRI_TE/00/00/0 Clear