similar to: Silence suppression problem with DECT phones and g729 codec

I've received my Com-on-Air DECT card this morning and while I have configured it (both the DECT registration and SIP to Asterisk configuration), I am running into a "Call missing Call ID from" error message. I can call from a DECT handset to an extension, but not the reverse. Not being an expert, it seems to me that Asterisk is looking for a CallerID from the DECT card. I

I've got the following setup: IAXy -> Dect Base Station. When you dial from a SIP phone (cisco 7960), the rings with very little delay. However, if you hangup it takes 3-4 rings after hanging up before the dect base station phone stops ringing. The same applies when an incoming call is directed from PSTN FXO -> Dect Base. Is there a fix to this I've looked about on voip-info but

G'day. I hope this isn't off-topic for the list. I am looking at an Asterisk setup that includes cordless phones. The three choices I can see, at this stage, are: * wifi phones * an ATA and a cordless analog phone * a DECT to SIP basestation The various wifi phone options don't grab us as suitable -- they are costly, have poor battery life and even the best have pretty mixed

Hello, I need to setup this configuration: - asterisk as IVR; - dect phones. So basically I need a "standard set" of features: - each dect phone has its extension so I can call it directly; - handover of a call with "R" key; - if a call is not replied by someone ring all phones. I have little budget. I can choose to buy a fritz!box or a gigasect dect/ip base station. Which

Anyone here that knows some hardware USB "client" (DECT) that can connect to a DECT base station and act as a "provider" in asterisk? Ergo, asterisk is the DECT handset, and connects to the DECT base station. Its also important that it also works with most asterisk-compatible devices, including for example raspberry's. The reason I ask, is that many providers in

And a PRI/BRI gateway? Is there any product ? Thanks Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Peer Oliver Schmidt Inviato: venerd? 20 gennaio 2006 10.17 A: Asterisk Users Mailing List - Non-Commercial Discussion Oggetto: Re: [Asterisk-Users] Dect to SIP PCI card Giordano Grandis wrote: >

Hi, Do you if a DECT-GAP (or DECT-CAP) compliant handset MUST or MAY support roaming and handover and are these functions transparent for handset (then, these functions are implemented in DECT base stations) ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080110/4254f602/attachment.htm

Hi all, I'm looking for a PCI card which i could install on asterisk box, with purpose to use 15-20 cordless dect phone in a very "dect cell". Is there anyone that could help me pls ? Thanks Giordano -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, I need to setup system of aroud 60 DECT phones with asterisk. So far I found http://www.grandstream.com/index.php/products/ip-voice-telephony/enterprise-ip-phones/dp715_710 However is there some cheap base station(similar to GSM cell) so I can handle all DECT phones centralized and plug it inside asterisk ? Thanks, Peter

Hi I have a problem with a new DECT phone I have bought The key pad works like a Mobile phone where you dial first then pick up the line, but it seems to dail too fast or spuriously, ie 012826736464 show on thew Asterisk console as 0012282677, could any one offer advice how to fix? Also when doing a ZAP bridge to this phone from an outside line the call is very echoy, but not an internal

Hello. Is anyone aware of a manufacturer of DECT cordless phone interface cards to act as the DECT base station that would be addressable channels under * ? Regards Petar -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040418/c8885bbc/attachment.htm

Hello, Does anybody have already use TEDAS VoIP DECT PABX or some Kirk hardware to integrate DECT to VoIP? Thanks! Ignace

Just setup *, got a developers kit FXO where the incoming/outgoing pstn is plugged in. I've then got an IAXy that is plugged into a Philips DECT phone. * is setup so that the [bell] section rings the phone - exten => s,1,Dial(IAX2/myuser,30) What's happening when someone calls my number is that the phone rings 3 times before you hear the dect phone ringing. Anybody got any ideas as

Hi folks, The recent mention of DECT on this list has got me thinking....... (yeah dangerours!) I have very little experience/knowledge with DECT and mainly where I have seen it used in a multibase base situation where handoff between bases occurr. This has been and ericsson system used as an adjuct to an ericsson pbx on a large multistorey property. If I remember correctly the bases are fed 2

Anyone have practical experience using inexpensive GAP-compliant DECT handsets with the Snom M3 basestation? When I asked Snom support, the answer was that 'basic functionality should work', but they didn't elaborate. I'm _guessing_ that means registering/unregistering with the base, making calls, and receiving calls (including presenting caller ID). They also stated that they

I see a variety of DECT 6 phones available CHEAP at costco. Is there a way to convert these to SIP? I recall someone talking about a Siemens devices that works with all DECT phones, making them SIP (I think).... -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081205/fdd14af9/attachment.htm

We've deoplyed a number of pure VoIP wireless (wifi & proprietary) phones, but not dect. Is there a simple overview of integrating DECT phones with Asterisk somewhere? I assume the DECT basestation has a multi-account SIP VoIP interface, and the handsets are just plain old dect? Can you push configuration info to individual phones? (Are they individually addressible / configurable

Hi, I just got some interesting information from Kirk Telecom (www.kirktelecom.com). This company has been in the business of providing DECT solutions (IP gateway, base stations, repeaters and handsets) either to be used with Cisco CallManager (SCCP protocol) or with the Innovaphone IP PBX system (H.323). Two important elements: 1. It seems they foresee a SIP version of their product in Q1

Anybody care to muse on Wi-SIP vs. SIP-DECT? My limited research indicates that none of the WiSip phones will ever be able to match the performance of DECT phones. Maybe I'm wrong but a Wi-SIP phone seems like a DIESEL sports car. There is nothing wrong with the technology, but it seems like a shoe-horned fit into the requirements of a wireless endpoint. DECT uses a wireless radio layer

Heya list, I need some advice/experience. Some of our customers are asking us about DECT solutions for their asterisk install. Some others will not go to asterisk if there won't be a DECT solution. They now have a Siemens or a Samsung PBX. Those PBX-es come with a DECT basestation and optionally repeaters etc. All those basestations speak some own protocol to the PBX, so we cannot use them