similar to: hardware that can accomondate 2 TDM24

Hi list, I'm wondering if there's a way for multiple users to share the same voicemail box and have their BLF flashing when voicemail comes, i.e. in a home phone system where there's a general vm for everyone. I'm using couple Grandstream GXP2020. Any suggestions? Kelvin Chan | Positronics Ent. Product Development | | unit 272

Hi guys, I'm looking for a affordable conference phone and a wifi phone that has a cradle. Polycom seems to make pretty nice conf phones but the price is a bit crazy for us. I saw the recommendation with ATA plus an analog Polycom phone but I do prefer a SIP phone. All because it's just too difficult to pull a phone cable into the current conference room. Is there any cheaper SIP

Hi, I'm running FC3 with kernel 2.6.11. All the binary files and zaptel kernel modules is not available to system at boot time. They are extracted in a ram disk at system startup and then zaptel modules are loaded manually and so on. I have no problem with this boot routine and i've been tested all digium cards (expect tdm24) and they work fine till now. The problem appeared when i

Hi,

Hi All, In the midst of trying to pilot a deployment of Microsoft Lync (mainly for non-voice collaboration, specifically IM) and integrate it with our Asterisk (11.6.0 if it matters) deployment and a "everything in one place" tool when people are out of the office. I have everything on the voice side playing nice from the Lync side (Lync->Lync, Lync->Asterisk,

i have a full fxo TDM24 and i have problem with installing it. when i run modprobe wctdm24xxp dmesg shows the following messages. and it waits for ever and nothing will happen. i'm sure that: - the power is plugged into tdm24 board - udev is configured and is working with other tdm cards. - zaptel.conf is configured. Zapata Telephony Interface Registered on major 196 Zaptel Version:

Hello guys, anybody here that can help me checking out this xml file, cause I am traying to configure some cisco 7911G phones to asterisk and I can't get it done.... thanks!!!! a paste of the file is here: http://pastebin.ca/1239083 -- http://celord.blogspot.com/ -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi All, Thanks for all of the help I've been given in the past and info I've picked up from this list over the years. I have an "official" Asterisk appliance (the AA50) running my PBX at home (we previously also had an AA50 in a satellite office-that one was recently retired and replaced with Asterisk running on commodity server hardware). Anyway - the AA50

Hi All, We've been running Asterisk for years in our offices but just recently replaced an Asterisk Appliance* in our smaller office with an actual server, upgraded the server in hardware in our HQ location and upgrading both ends to 11.5.0 with Gareth's patch for Cisco phones. 99.99% of our endpoints are Cisco 7961Gs. Each office is more-or-less standalone for ease of management and

From: Martin Schwidefsky <schwidefsky at de.ibm.com> The SIE instruction on s390 uses the 2nd half of the page table page to virtualize the storage keys of a guest. This patch offers the s390_enable_sie function, which reorganizes the page tables of a single-threaded process to reserve space in the page table: s390_enable_sie makes sure that the process is single threaded and then uses

Hi All, I've looked through the archives and tried several variations in Google, and I haven't found anything on-point... So I'm hoping someone here may be able to help this relative Asterisk neophyte shed some light on an issue: I have a box running Asterisk 1.4.22 in our lab with several Cisco 7961G phones and an AEX804E card (4 FXO, hardware echo cancellation). The server and all

Hi All, I posted this a couple weeks ago with no response, I'm hoping that someone will see it this time around and be so kind as to offer advice for resolving this issue (or point me in the direction of a better place to ask) "Some" (but not all) calls on one of our Asterisk boxes are being dropped in Voicemail -- only in voicemail -- after about 20 seconds with the error logged

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA512 Hi all, we're experiencing "Out of Memory" Problems caused by Sieve-Filters delivering mail to huge IMAP folders. From the logs, I'm beginning to think the problem is that the sieve/lmtp process loads the "dovecot.index.cache" file apparently twice into memory to do something with it. We've set our memory limit per

Hi My asterisk output is: chan_sip.so => (Session Initiation Protocol (SIP)) Asterisk Ready. -- Registered SIP '201' at 192.168.0.55 port 33906 -- Saved useragent "X-Lite release 1011s stamp 41150" for peer 201 -- Executing [907768385144 at default:1] Dial("SIP/201-083e75c0", "ZAP/g1/907768385144|60") in new stack [Oct 4 11:54:27]

I checked the app store and haven't found anything promising, but I figured I'd ask here. Does anyone know of a SIP or IAX client for a non-jailbroken iPhone that will communicate directly with a machine running Asterisk? I know that there's at least one offering that seems like it's essentially a proxy (App runs on iPhone, iPhone talks to 3rd party server, 3rd party server talks

Hi All, I have a ticket open with Digium, but based on their previous lack of support for the Asterisk Appliance, I'm not really holding my breath - and, honestly, I'm not 100% convinced it's a Digium issue in the first place (but I don't know where else to point fingers). We have an AEX-804E (PCI Express, 4 FXO ports, Hardware Echo Cancellation) in a Dell PowerEdge 1950 with

"Why Siphon doesn't allow to receive a call when it doesn't run Apple doesn't accept (for the moment) an application runs in the background= . So, when Siphon doesn't run, the SIP server of your provider doesn't know your iPhone." --0015174c3c60a73ef5046656ca27 Content-Type: text/html; charset=windows-1252 Content-Transfer-Encoding: quoted-printable

Hi All, We're using Asterisk 1.4, and Cisco phones exclusively (mostly the 7961G, but a few 7911Gs and one 7912G for the time being-all running the SIP firmware image, plus a few analog extensions until the next capital funding cycle). Each user has a phone at his or her desk, but there are also a growing number of "common area" phones (hallway, kitchen, conference rooms, data

"Why Siphon doesn't allow to receive a call when it doesn't run Apple doesn't accept (for the moment) an application runs in the background= . So, when Siphon doesn't run, the SIP server of your provider doesn't know= your iPhone." --_000_EC80F07C30CE3E46B2AD6B4407BE086F0C2AAD0248cworksmailcwo_ Content-Type: text/html; charset="us-ascii"

When did Dial() with a custom ring cadence replace the default from indications.conf for subsequent calls? indications.conf: ringcadence = 2000,4000 asterisk -rx "dahdi show cadences" r1: 667,1333 extensions.conf: exten=> 201, 1, Dial(DAHDI/1) exten=> 202, 1, Dial(DAHDI/1r1) exten=> 203, 1, Dial(DAHDI/1r0) Dialing, in sequence: 201 -> 2000,4000 ; Good 202