similar to: Preferred Clock

Hello According to this article, this nice little unit can only use the PSTN port for outgoing calls (ie. as a backup in case the connection to the VoIP provider stops working), but not incoming calls: http://tinyurl.com/mwjmo8 Can someone confirm that Atcom made this strange decision, and that there's no work-around? Thank you.

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Hi, We have a PRI Trunk (physical E1) and we are getting some rather weird and very isolocated problems. On outbound calls to specific numbers, it would seem to me that DTMF from the remote side is affecting the local asterisk system. Basically what happens: - We make a OUTBOUND call via the PSTN (PRI Trunk) to a remote System - Remote Answers, and converse - Remote sends DTMF on their site to

Hello- After configuring DAHDI and starting asterisk, I get the following message continuously on the Asterisk console: WARNING[2057]: chan_dahdi.c:4158 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! My card is a D410P configured for E1, only the first span is configured, and configuration snippets are as follows: From /etc/dahdi/system.conf:

Hi, I've noticed that one of my new servers (new mobo) if drifting slowly backwards in time (in aprox. 24 hours, system time drifts back 5 minutes). I have an ntpd process which is supposed to sync with a lan time server but it's not quite working. So I'm launching a manual ntpdate or ntp-client once an hour and that seems to work. However, suppose I update system time at every hour

I just managed to put in a TE410 card in an Asterisk box to work with OnRamp 20(E1 downunder). I am able to dial in but was not able to dial out. Can anyone offer me some advice please? In my extensions.conf, I just put in: [default] ... exten => 0,1,Dial(Zap/g1) and I get this on the console when I dialled 0. -- Executing [0 at default:1] Dial("SIP/5166-b76004f8",

Dear, I always had one E1 card with one span, so I've never had any problem in set it up through /etc/dahdi/sustem.conf and /etc/asterisk/chan_dahdi.conf because I put span=1. But now I have a PBX with two E1 cards with 4 span (8 span in total). How do I have to define both card in system.conf and chan_dahdi.conf, and how do I have to refer each span to the corresponding card ??? Thanks a

Hi, i'm currently using Originate command on AMI, i can call a certain channel like a SIP user SIP/1000 then once 1000 is answered it dials out to amobile or landline. Would just like to know if i can use AMI to dialout to a mobile or landline first (instead of SIP user) and once answered, dial another mobile or landline again. If not is it possible to call a macro from the AMI? i think

We are using AAH with Asterisk 1.2.7.1 with a TE405P as listed below. We are getting frequent restarts on the spans which lead to dropped calls. I have pasted some hopefully pertinent information below -- anyone have any clues that might help? Thanks Next line is repeated throughout messages, going through every channel in every connected span. asterisk/full.1:Apr 24 01:15:25 VERBOSE[4196]

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

Hi All, I am facing problem with E1 line. I have installed Asterisk (1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10) But every now and then I face problem of down E1's. The log show lot of entries like "pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2" This happens on a regular basis and the E1 becomes up after some time. My

Hi, I'm trying to bring up two PRIs from qwest with asterisk and dahdi. I'm using an OpenVox D410E and the drivers are loaded. My system.conf looks like this: # Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" B8ZS/ESF RED span=1,2,0,esf,b8zs bchan=1-24 # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" (MASTER) B8ZS/ESF RED span=2,1,0,esf,b8zs bchan=25-47 dchan=48 These

Hi, I have a digium card (igium, Inc. Wildcard TE405P quad-span T1/E1/J1 card 5.0V (rev 02)) 4 ports I want to make a loop test between digium card E1 to test the configuration of dahdi What I want to do scenario is I connect port 1 and port4 in the digium card with E1 cable SIPcall-->E1 Digium port 1--->(Loop)E1 port 2---->sip extension local. kindly can any can help me to

hello list, i have installed 2 diguim cards in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

Hi, Running 1.4.26.1 here. I have installed TE420B card in my server, and followed the appropriate steps (as far as I know to configure it). This TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling type. When I dial out, I get this message: Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0

Dear members of the list, I have difficulties to obtain sync with a Digium TE420 PCI Express For four entries E1, In my case I am with only 3 E1s available to configure. The telephony operator is BrasilTelecom and Signaling is R2 Digital. The information I have is that are E1s with 32 channels, not have sure. My settings Have been based on the link reference:

Hi, I'm getting the following error from an asterisk 1.6.0.9 installation: [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: Asked to delete sched id -1??? [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: No more room in scheduler This repeats a few times, then asterisk crashes. I can't seem to locate any info on this error at all. I'm using

hi folks. recently some of our customers complained about bad voice quality on the phone system. i looked at the logs and found a lot of these: [2012-11-03 08:26:38] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:45] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:54] NOTICE[11305]

Greetings, I am writing an AGI script that needs to check on the idle/busy status of a number of SIP peers (mostly SPA9xx phones, with a few Polycoms and Snoms thrown in for fun). Is it possible to call Asterisk functions (e.g. SIPPEER) from AGI scripts? Based on my Googling, I would guess in the negative. I have tried various permutations of Set() and Eval() without success. I have also

I have asterisk 1.4.21 and web meetme (latest release 3.1) I have also installed the latest versions of mysql and php. I followed the readme file that came with the web meetme app and everything seemed to go fine up until I realised the module wasnt being loaded. When I stop asterisk and try to start it, it errors out and does not load and I get the following message: Parsing