similar to: No subject

I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2 I've got a 2 port T2XXP card attached with on T1 currently plugged in. Inbound calls work fine, but outbound fail with the rather cryptic: [May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) There are similar threads I've found on the

--- span_1 = DAHDI/g11 1,1,dial(${span_1}/${EXTEN:0}) --- The configuration was rsync'd from a working pair of asterisk servers in another office. The only difference was the version 1.4.22 for the original servers that were operating as expected, 1.4.24 and 1.4.24.1 for the new servers. Included in both working and non working servers is the following configuration:

Hi, I am having problems with an Asterisk with a Digium TE205P card. The issue is that the Ring Back Tone is noisy. I am making modem's calls and this noise influences on the initial negotiation protocol, so modems have to recall. My configuration is: Asterisk version: Asterisk 1.4.21.2 Linux version: CentOS release 5.2 (Final) Card: Digium TE205P

Hi everyone! I'm quite a newbie at this Asterisk stuff so please bear with me. We've recently decided to start training in Asterisk via AsteriskNow! Asterisk version is 1.4.18.1 through AsteriskNow! 1.02 The box we have is paired with a Digium TE110P and we've managed to get it to the point where incoming calls via a single DID (from NTT Japan) can be received and answered

Hi. My configuration is Elastix 1.5.2-2 (asterisk 1.4.24, libpri-1.4.3-5, dahdi-2.1.0.4-7 ) and OpenVox d210e connected to telco provider (Euro ISDN). Here is my /etc/dahdi/system.conf: # Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) HDB3/CCS ClockSource span=1,1,0,ccs,hdb3 # termtype: te bchan=1-15,17-31 dchan=16 echocanceller=oslec,1-15,17-31 # Span 2: TE2/0/2 "T2XXP

Folks, I have a Merlin Legend R7 V10.0 with a 2 100D cards. I have 1 card in slot 4 going to CenturyTel, and the card in slot 10 going to a flip cable to a TE110P card in a Asterisk 1.6.x box. I have routing setup on the Merlin to send a block of numbers to the Asterisk. Currently the PSTN can dial the Asterisk Extensions. The Asterisk can dial Merlin Extensions. The Merlin can Dial Asterisk

We recently updated our Asterisk (1.4.24) box from Zaptel (1.4.12.1) to Dahdi (2.1.0.4). Everything seemed to go smooth with the exception of meetme. Meetme seems to not be able to find a zap channel for conferencing. We use voice introductions in our conference bridge and it seems to break that feature. The error from the console is.... # app_meetme.c:2593 find_conf: No Zap channel available for

Hi, I have the following dialplan. Problem is, if the user authenticates, * starts counting as billable seconds even if i hangup the phone before the called party answers..And also as disposition.. it accepts all calls authenticated as 'answered' If i commentout the authentication line everything works as it should be. How should i use authentication that, it should accept it as aswered by

Hello, I wanted to add a failover trunk to my asterisk configuration. I got 2 gateways for my calls.. one is a pri other is voip trunk. I want to keep my trunk for failover. I am using ast 1.6 with asterisk-gui. But when i add a failover trunk for test purposes asterisk-gui adds the following line to my extensions.conf. where superonline is my voip provider and span_1 is failover trunk. exten =

Hi, I got the following problem. I am doing a maximum likelihood estimation for a Kalman Filter. For this purpose, I have to invert an error matrix Ffast of dimension "no. parameters X no.parameters". The usualy optim methods often find only local minima, so I decided to make the optimization using the SANN algorithm, which is very slow already. However, this becomes a real problem

Hi, i managed to connect to Ericsson MD110 with PRI at last. And made a successful call thru asterisk to ericsson. But when i try to call from ericsson to asterisk i got an error on asterisk side. And i couldnt figure out why. Here's my extensions.conf about incoming calls. [DID_span_1] include = DID_span_1_timeinterval_all,${timeinterval_all} DID_span_1_timeinterval_all] exten =

So, to make it simple, my domain is KRH, I am successfully joined, and can issue wbinfo -u or wbinfo -g and get expected results. Every query I make about the domain works However, I'm trying to add a domain user (me) to my local Print Operators group on this freebsd machine. Using Samba 3.5.6, FreeBSD 8.1 Clean install of everything yesterday. So, I'm trying to add KRH\jdown to

Hi all, Sorry to bother you with the potentially not too bright question, but since I cannot get it to work, I'll have to ask someone.. I've got this vector: > token [1] sal skal skal bak b_r d_ gal kal l_r n_r pak p_r [13] sal sl_r sn_r spak sp_r st_r s_ bak d_ gal l_r pak [25] p_r sak sl_r sp_r t_ kal n_r s_ st_r sak kal

I'm currently running into a little trouble with the kfilter method, and would love some clarification if you are able to offer it. When trying to run kfilter, I've been running into errors that seem to result from having mismatched dimensions. Specifically, the dimension of my observations is 2, while the dimension of the state space is 4. In the filterstep function (file sspir_kfs.R),

Hello all. I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box. NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco Incomming calls from the telco to the asterisk box to the NEC work fine with indials and everything. Works sweet. Outbound from the NEC to the Asterisk box fail. Giving an long dial tone that then times out. Ie, pick up NEC handset, dial

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

the Telco, I can make calls in. What I am trying to get though is how to pass through the DID range. The E1 that I am connecting to the Telco with, used to connect direct to the NEC system and already has hunt group calling enabled for all 30 channels. Also, I was given a 100 number indial range (from 00 -> 99). If the E1 is connected to the NEC directly, I can call 5555 7320 and the NEC

Hello, I have been struggling with the configuration of this card on my box. I have a T1 line and I am trying to setup asterisk with it. I followed all the instructions and I still see a blinking red light on the card. I use fedora 12. If everything is fine should I see a green line when I plug in the T1 line ? I want to isolate the issue so I di not start asterisk. When I run asterisk I get

Hello list i have an issue with my dahdi_channels.conf in span 1 when i use it like below i can do my outband calls without issue ; Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) group=0,11 context=from-pstn switchtype = euroisdn signalling = pri_cpe channel => 17-31 context = default group = 63 but when i add in channel 1-15 like: channel => 1-15,17-31 i receive all

Hi I am trying to connect asterisk with a Cisco GW 2600 with E1 pri using a Digium, Inc. Wildcard TE210P dual-span T1/E1/J1 card 3.3V (rev 02), Errors: [Jan 28 17:32:33] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 up [Jan 28 17:32:33] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think we're the CPE, but they think they're the CPE too. [Jan 28 17:32:34] NOTICE[6182]