similar to: E1 conection to a Cisco2600

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

Hi all. I have this problem with my Digium 2E1 card and PRI, for hours It works well, with some meesages... [Aug 10 09:20:31] NOTICE[32270] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 But PRI continue up....hours later... PRI go down. I thought the problem was in the telco, but the strange thing is that I have a loop cable in the second E1 and when I scan both E1

Hi, On a Asterisk 1.8.12 system working OK for months (>100k calls proceed), users are complaining for bad audio. My setup is: PSTN <--E1/PRI ---> Asterisk <--- E1/PRI---> Siemens HiPath <---E1/PRI ---> PSTN asterisk -rx "dahdi show version" DAHDI Version: SVN-trunk-r10414 Echo Canceller: HWEC asterisk -rx "pri show version" libpri version: 1.4.12 A

We fairly recently switched service providers for our 4 PRI circuits. Since that time, we started to notice some failed inbound calls. These calls terminate with an ISDN cause code 47 'resource unavailble'. Most of the time I see this error on the first or second channel on the second span in a trunk group (This is the providers trunk group for hunting, not an Asterisk trunk group). All

Hello, I have an Asterisk box with a digium TDE205p card. The problem is that I have several "Goto(s-${DIALSTATUS}" sentences and while the call is trying to find a free channel to establish the call, I get a little noise in each "Zap/... is proceeding passing it to Zap/..." line. My configuration is: Digium card: TE205P Asterisk Version: 1.4.21.2

Hi fellow asterisk users, I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel module) an approx. 100 snom320. The whole installation is running without issues since 5 months. Without having changed anything on the asterisk server for at least 2 months, i noticed "clicking sounds" at external calls over the PRI. Asterisk constantly throws the following messages: ...

Hello Team I have installed the new DL580 and used the new TE420B to add capacity on our ivr. Before I put new E1?s I decided to first move the old e1 from the old system to this new one but it has errors which not only affect the audio quality, but also cause the asterisk to refuse any call after sometime even though the channels seems up and active {seems d-channel fails}.. When processing

fact I'm surprised that's changed (FreePBX's DAHDI module created the current config -- i.e. the one I posted in my original email). I'll change that back and see if that makes a difference, but I'm pretty sure I used the above configuration in a previous attempt with the same results. Also, I have indeed received the following messages prior to the interface going down and

Hi. My configuration is Elastix 1.5.2-2 (asterisk 1.4.24, libpri-1.4.3-5, dahdi-2.1.0.4-7 ) and OpenVox d210e connected to telco provider (Euro ISDN). Here is my /etc/dahdi/system.conf: # Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) HDB3/CCS ClockSource span=1,1,0,ccs,hdb3 # termtype: te bchan=1-15,17-31 dchan=16 echocanceller=oslec,1-15,17-31 # Span 2: TE2/0/2 "T2XXP

Hello list i have an issue with my dahdi_channels.conf in span 1 when i use it like below i can do my outband calls without issue ; Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) group=0,11 context=from-pstn switchtype = euroisdn signalling = pri_cpe channel => 17-31 context = default group = 63 but when i add in channel 1-15 like: channel => 1-15,17-31 i receive all

the Telco, I can make calls in. What I am trying to get though is how to pass through the DID range. The E1 that I am connecting to the Telco with, used to connect direct to the NEC system and already has hunt group calling enabled for all 30 channels. Also, I was given a 100 number indial range (from 00 -> 99). If the E1 is connected to the NEC directly, I can call 5555 7320 and the NEC

Hello. I have a TE212 configured in E1 mode. This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured): cat /proc/zaptel/2 Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN 25 TE2/0/1/1 Clear 26 TE2/0/1/2 Clear 27 TE2/0/1/3 Clear 28 TE2/0/1/4 Clear 29 TE2/0/1/5 Clear 30 TE2/0/1/6 Clear

Dear All; I am afraid from IRQ misses: 1 The ISDN E1 was working fine on the machine, the electrical disconnected and then the Red Allarm. I checked the dahdi and I found that I have to reinstall dahdi again and I did. But still not becoming UP. The output of the cat /proc/dahdi/1 is following (I am afraid from the IRQ misses: 1, so if it is a problem what is the solution)? [root at CC

Hello, I have an Asterisk system in the UK using ISDN service from BT. My problem is that the called number is always passed to the provider with the Type Of Number declared as ?national? despite pridialplan (and prilocaldialplan) is set to ?unknown?. My questions are: - How can I find out what the effective value is for the above two variables without actually making a call? (I have very

Hello, I've got a running system in which logs are full of messages such as: [Jun 10 07:24:14] NOTICE[2414] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 The strange thing is those messages are coming from a single span. My setup is : Asterisk 1.6.1.18 Junghanns OctoBRI with wcb4xxp driver libpri 1.4.10.2 dahdi 2.3.0 3 BRI lines in PtMP mode What does this

Hi, After upgrading to DAHDI 2.4.0 from Zaptel, I noticed a lot of HDLC errors on my console: [Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 [Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 These errors prevented calls from being made and received on my PRI spans. This seems

Hi, I have problem using Asterisk.I have isdn-pri and openvox d110p card in my computer.They are connected with RJ-45 (1,2,4,5 pins to the card and all pins to the isdn done by telco workers). I got green led on isdn which is sign that isdn is working and that is connected to openvox, right ? I compiled newest versions of libpri zaptel and asterisk and had no problems during that. When I started

Hi I have this escenario: |SIP or H323 phone|---->|Cisco2600|----E1-pri---->|Asterisk|------>IVR, A2Billing, etc... The problem is that I can not hear any audio when call from 'sip or H323 phone' and configure something like: exten => _01XXXXXXX,1,Playback(thank-you-for-calling|noanswer) ... It works if I remove the 'noanswer' parameter but in this case it connects

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'