similar to: WCTDM/Zaptel memory leak

Hi, Built a new server at the weekend and install Asterisk 1.6.0.9 and IAX and SIP work great :) The one problem I am having is getting the OpenVox (TDM400 type card) to work. It is successfully identified using WCTDM kernel module and dahdi_scan picks it up just fine. The issue is when I try and setup dahdi_channel.conf as it fails everytime. When running asterisk -rvvvv I see the port pick

Hi, I'm experiencing an issue with my x86_64 machine containing a Hauppauge PVR-500 (ivtv) and a Digium TDM400p (wctdm, part of zaptel) PCI cards. Independently of each other both cards work fine, but once the wctdm driver is loaded and mythtv tries to record something on the PVR-500 the wctdm driver freaks out. The error message is see is "TDM PCI Master abort" printed over and

Hi :) My employer is looking to move a call centre to a new office, and has been increasingly frustrated with their legacy PBX (call-logging licensing and hardware upgrade costs). So I've stepped forth as the Open Source Pedant and suggested Asterisk so we can do all our own CallerID / call logging / analyses, and make use of IP Phones / teleworking, etc. The problem begins in that I only

Greetings to one and all on this fine list; We have the current system: Meridian 1 Option 11 +-------------------+ | | ISDN/30 (DASS/2) ===> |NTAK79BB (2MB Pri) | | |<-->4x16 port Digital / 1x16 port Analogue ISDN/30 (EUROIDSN) ===> |NTBK50AA (2MB Pri)

Hello, I have found a "bug", I think in the way TDM400P cards handle FXO interface disconnect/re-connect problems. Normally I do keep all the wires connected from my CO / PABX quite securely, but I had a need to re-route the cable from one side of the desk to another, and I simply disconnected the RJ-45 connector and plugged it back in. THIS PROMPTLY RESULTED IN VERY VERY SCRATCHY AUDIO

Hi, Are there any hardware for ISDN30 ? if yes any problem with this ? is i out-of-box like ISDN2 but with 30 linies ? Do I need more than the cable from my teleprowider and a PCI-card ? /HHA _________________________________________________________________ Find high-speed ‘net deals — comparison-shop your local providers here. https://broadband.msn.com

I'm chasing down a pop/click type of disturbance on a PBX system. Strangely, the disturbance is only heard by the outside caller, the internal recipient hears the caller crystal clear. This seems to have crept up when upgrading the zaptel driver to the 1.2 series while running 1.0.10. I went ahead and upgraded the entire system to 1.2.4. The system is a ~2Ghz AMD 32bit system, with 512MB of

Just installed Asterisk 1.2 on a brand new clean machine running RedHat 9.0. I have a TDM400 card inside. When I boot, the card seems dead. When I do: modprobe wctdm modprobe Zaptel the lights come on and all seems fine, until I reboot that is... After a reboot I have to repeat the modprobe. I shouldn't have to do a modprobe every re-boot should I? How do you get the drivers to load

Hello everyone, I want to connect a fax to an FXS port (TDM420P). For testing purposes, I connected an analogue phone to it first. However, when I pick it up, I cannot hear anything at all. The power cable is plugged into the card, the port is configured to use fxo-signalling. Also, immediate=no. Here's the files: /etc/zaptel.conf: # Autogenerated by /usr/sbin/genzaptelconf -- do not hand

I got a new motherboard and upgraded Asterisk, ... However, I am not lucky enough to get it running again. To compile went ok, besides this remark at the end of asterisk: WARNING WARNING WARNING Your Asterisk modules directory, located at /usr/lib/asterisk/modules contains modules that were not installed by this version of Asterisk. Please ensure that these modules are compatible with

Hello all What I'm looking for is some plain speaking advice on ISDN. Currently using 4 analog lines connecting via a four port TDM400P FXO card. We need to physically move our installations, and on requesting the analog lines be moved - our telco (BT) is suggesting we replace our analog lines with ISDN2. We would have 3 x ISDN2 connections, giving us six voice channels. They've

Hi, I have a running asterisk 1.2.1 (bristuffed) with a TDM400 Board. Connected to 1 port is am ordanary Fax Machine. Everything 'seems' to work, however receiving faxes is very unreliable. Sometimes I receive a normal page, without problems. Sometimes half of a page and the rest is scrambled, but most often, I receive nothing and the other site reports a Fax error... The Fax machine

Hi, I've been avoiding investigating this issue for a while; I used to revert to a previously compiled version of zaptel & a previous kernel (as at some point I think I stopped being able to compile the older zaptel against the newer kernels) and all was well. However I've now upgraded kernels again and it seems silly to hide from the problem - here goes, let's try and fix it! At

So I have an application where the users want to divert incoming calls on one analogue line out to another analogue line - both lines are supplied by BT and theres a TDM400 in the box. Call comes in, system Dial's the forwarding number and bridges the calls. Works fine. Until one (or both) leg hangs up. And the box never sees the hangup. So it sits there with both Zap channels open

Has anyone had success with the TDM400 in production? I have multiple boxes where these cards lock up and the only thing that will fix them is to unload *, modprobe -r wctdm, modprobe wctdm, load asterisk. Does not matter if it is a FXS/FXO module. I know this topic has been discussed many times before, but my questions is not "is anyone else having this problem" since I know that

Hi, I'm trying to get up and running a TDM400 with a standard italian pots line but i'm having problems at getting asterisk to detect when the line get answered on outgoing calls. I'm using asterisk 1.6 beta 9 with zaptel 1.4.11. I tried with and without answeronpolarityswitch=yes but it didn't change anything at all. With callprogress=yes answer get never detected. With

Hi, I am the "IT guy" at a small startup based in UK. At the moment we have 3 analogue (PSTN) lines and we will be adding another 2 or 3 soon. Later on we should be changing to ISDN30. One of the partners mentioned getting an analogue PBX now, and when we move to ISDN, then get a digital PBX. I though of Asterisk. I have seen the website in the past and I know that it can do the job

Hello The Ubuntu Asterisk package doesn't install /etc/modprobe.d/dahdi.conf, so I was wondering where to put the following line: ======= options wctdm opermode=FRANCE ======= Should it be in /etc/dahdi/modules? ======= options wctdm opermode=FRANCE ======= Thank you.

After getting zaptel from the CVS server, compiling and installing it I type: modprobe zaptel and all is well. Then I type: modprobe wctdm and I get this: modprobe: Can't locate module wctdm Any idea why? I did this yesterday but with the CVS head of Asterisk and I got by this part without a problem. I reinstalled it all today because I wanted the stable release on our server since we

Hi, I've installed Asterisk with a TDM400P on a Debian Etch distro. When I reboot the server I get zaptel and wctdm automatically loaded. I'd like to avoid this behaviour. How can I disable this automatic "modprobe wctdm" during boot? Thanks Giorgio