similar to: libpri and NT-Point to multi-point

Hi, I'm experiencing difficulties to get a B410P running with Asterisk 10.3.1 and DAHDI 2.6.1. Am I supposed to use DAHDI for this card and ISDN BRI for my country (Belgium)? thx, BC

The DAHDI docs actually include the 'steps' that used to be in Zaptel's 'make b410p'. These steps involve downloading and compiling mISDN. Why re-invent the wheel? Just a thought :-). As for the 100ohm termination bit - it's simply changing a couple of dip switches on the b410p card (as described in the manual). Andy -----Original Message----- From:

Hi, As you may know, these ISDN BRI features are very important here in Europe as ISDN Basic Rate Access is very popular among Small & Medium Entreprises. I don't really know why but it seems that in many countries, default is to install small PBX using Point-to-Multipoint (PtMP) mode as opposed to Point-to-Point (PtP) which is the norm for PRI. So basically, in several countries, SME

Hi all, I am having trouble setting the signalling method for the B410P using DAHDI. Asterisk complains that it has never heard of 'bri_cpe' or 'bri_net' - but it doesn't mind having 'pri_cpe' etc. ERROR[4294]: chan_dahdi.c:11327 process_dahdi: Unknown signalling method 'bri_net' Dahdi - dahdi-linux-complete-2.1.0.4+2.1.0.2 Asterisk - 1.4.23.1 Libpri - 1.4.9

Hi, After an upgrade, I discovered yesterday strange things I would like to share here. Basically, I'me comparing platforms: The first one is a 2.6.26 (Debian Lenny) platform, with Asterisk 1.6.1.18, Libpri 1.4.10.2, Dahdi revision 8853 (must be between 2.3 and 2.5, I think). The second one is a 2.6.32 (Debian Squeeze) platform, with Asterisk 10.5.1, Libpri 1.4.12, Dahdi 2.6.1. Both are

Hi, Until now I've been using my Digium B410P cards with misdn 1.0.x. I would like to upgrade my systems and am now wondering which is the "best" route to take: - use the latest release of misdn v1 - upgrade to the latest "stable" kernel and use the built-in misdn v2 - use misdn v2 as a seperate package (disable misdn in the kernel) - use dahdi's support for misdn

Apart from you were dialling out on your inbound context and vice-versa. The best advice I can give now is to change to mISDN - as this is proven to work with v1.4 and v1.6. Actually - have you tried putting the 100ohm termination on for your NT port? I need to do that with mISDN as it only allows ptmp for ISDN extensions. Cheers Andy -------------- next part

Hello, Is it possible, for testing, to connect an cat5 straight patch cord between 2 ports of a Digium B410P card and use these 2 ports as a normal dahdi trunk ? I've tried this: One port is set as NT, the other as TE. I would expect timing to come for system hardware so I choose in /etc/dahdi/system.conf : span=1,0,0,ccs,ami span=2,0,0,ccs,ami Results: - both ports lights are green -

Hi all, So, we reverted the LibPRI version and tested it, and then tried with the latest version of everything. Still no changes. The BRI line is in PTMP. If we set the configs to PTMP in the genconf_parameters and try it, we get the following: [Jan 21 17:32:20] ERROR[20341]: chan_dahdi.c:12645 dahdi_pri_error: Unable to receive TEI from network! If we set it to PTP (which it is not) we

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Hello all, I'm trying to conect two asterisk servers using two B410p Digium cards. One card on each server. I just setting up the first BRI port on server A as nt_ptp and the first BRI port on server B as te_ptp. I use an ethernet wire to connect the first port of server A (nt_ptp) with the first port on server B (te_ptp) but the port light cotinues blinking on red on both sides once the

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Hi, I need to rebuild a system which has 4 BRI ports and is connected to Point-to-multiPoint lines, in a country where telco often "drop lines for energy savings". I'm planning to use latest 11.4.0 asterisk version along with dahdi and libpri (no misdn). Which version are recommended for Dahdi and Libpri ? My main requirements are, beside having calls coming in and out: - keep a

Its been a few days, I was wondering if anyone else has any ideas on how to get this to work? If not, could I ask a the direct question as to if anyone here has (or knows someone who has) successfully got something like a Cisco Router to successfully establish an ISDN data/Internet connection through the Asterisk PBX?

Hi, Has anyone information about BRI hardware supported by 1.6 libpri ? In another thread, I was told a basic BRI card with HFC chipset (Bewan Gazel 128) was supported but I would delighted to lear about other harwarde (and specifically about Digium B410P). Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Hello, Following my first mail about this issue [1], I think I know now what the problem is. When I have both lines being used and a third call comes in, the person calling doesn't get a busy tone, he gets something like line unavailable. I've been debugging mISDN and I think the reason is because asterisk is sending the release cause as 0. P[ 3] --> channel:0 mode:TE cause:0

The Asterisk Development Team has announced the release of version 1.4.11 of libpri. This release is available for immediate download at http://downloads.asterisk.org/pub/telephony/libpri/ This release contains many fixes and new features, among them being: 1.) Support for NT-PTMP BRI links, including support for multiple TEIs and connecting of BRI phones. 2.) Support for allowing persistent

The Asterisk Development Team has announced the release of version 1.4.11 of libpri. This release is available for immediate download at http://downloads.asterisk.org/pub/telephony/libpri/ This release contains many fixes and new features, among them being: 1.) Support for NT-PTMP BRI links, including support for multiple TEIs and connecting of BRI phones. 2.) Support for allowing persistent

Hi, Reading http://www.asteriskguru.com/tutorials/bri.html , it seems PtP is the way to connect businesses but if you read http://public.swbell.net/ISDN/connect.html you would think the opposite. Can anyone elaborate a bit PtP or PtmP respective advantages ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL: