similar to: Door phone

Hi, Is it possible to "regret" blind transfer while its ringing (not answered)? Thank you! Best regards HB

Hi, My Asterisk systems runs like a dream with mISDN, SIP and even and old Digium board. But have almost in every conversation some irritating DTMF being generated. The seems to be just as often from all trunks but are worse if noise load speaker in other end. Any good advices? Where to look for forgotten DTMF detection settings? Thank you! HB

Thank you, very interesting! As I understand the Digium card is used as a interrupt source for Asterisk? Is there a diagnostic tool available ? Anybody else experienced a simmialr problem? Thank you! HB > From: > covici at ccs.covici.com > Date: > Sat, 12 Dec 2009 19:04:23 -0500 > To: > Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users at

Hi, I would like some advice from you on how to configure a multi line phone the best way! So far I have given the phone 4 sip accounts one for each line, this is a lot of work and gets messy. Is it a better way to do this? Thank you! Best regards Helge-Bj?rn

Hi Any solution for connecting Asterisk to Skype without using fsx/fxo hardware ? Best Regards HB Norway

Hi all, I have had (what I consider) an odd request. The installation I'm working on now is an office on a multi-floor building. They 're looking for some kind of solution with the phone system to provide door control. We are a non-profit so of course I'm looking for something VERY inexpensive. I'm sure /someone/ has done something like this. I'd appreciate any ideas. Cassius

Hello Everyone, My company is about to deploy * as replacement for our existing commercial Altigen PBX. Meanwhile, I've been trying to find the best cost effective SIP VoIP phone which we can use in office for 20-30 employees, as well as a few remote staff. Normally I wouldn't post about a VoIP phone, however, this phone was released less than a week so I thought I'd give some

Hi Everyone, Looking to replace a condo intercom system. Apparently the current one taps into the lines and dials phone numbers but needs to be changed as it's faulty. I will probably still use the same analogue dialing and back it up with a VoIP line and use the current cabling that is in place. But as for as the door opening function goes, I am not sure how to interface and how open these

I want to use a voip speaker phone as a room monitor. Requirements: A phone that I can set to auto answer in speaker mode. A phone with a good speaker phone. Ability to make the audio one way. I want to monitor the room but not have my voice heard in the room. Yes, the mute button can accomplish this also. I have been using the SPA942's around the house (the speaker is just ok but

Does anyone have any recent news on the Virbiage FT201 IAX Hardphone? I'd *really really* like to deploy these phones instead of SIP hardphones, and I can't help but wonder if I'm going to shoot myself in the foot (or another sensitive area) by deploying a ton of SIP phones just to find the IAX Hardphones were released a week later... Thanks, Brian D'Arcy

Hi! I tested two different implementations of the robust MCD estimator: cov.mcd from the MASS package and covMcd from the rrcov package. Tests were done on the hbk dataset included in the rrcov package. Unfortunately I get quite differing results -- so the question is whether this differences are justified or an error on my side or a bug? Here is, what I did: > require(MASS) >

This is not specifically Asterisk-related, but I think that sometimes a "pre-emptive" clue is a good thing. Viking Electronics (http://www.vikingelectronics.com/) has some neat widgets that attach to phone lines, which I'm sure many of the people on this list would find at least somewhat useful in conjunction with their Asterisk systems. Many of the widgets can be replaced with

Asterisk as a phone system makes perfect sense in a condo. You can get all the DID's you want and eliminate costs for the owners. You can offer standard FXO for people who don't care and IP sets for people who want to "upgrade" to feature sets. Your door openner is a piece of cake. 1. Create an option in your dialplan only in the "from-access-door" context that reads

I just acquired a copy of "Statistical Models in S", I guess most commonly known as the "white book", and realized to my dismay that most of the code is not directly executable in R, and I was wondering if there was a source discussing the things that are different and what the new ways of calling things are. For instance, the first obstacle was the solder.balance data

Hi I have installed the http://asteriskathome.sourceforge.net/ with a Digium card with no problems, very good ! Now I want to install my Billion PCI ISDN card (HFC based) in TE mode. I get a little confused with Isdn4Linux, ZapHFC HIAX and the need to install Capi ! Please suggest best and easiest approach ? Thank you ! HB Norway

Hey all, I know you all saw the topic and let out a groan. However, I understand how to get an overhead paging system to work with respect *, however I am now looking for a small(?) paging amp, that I could hook 3 or 4 horns to. I would like to just have the * extention be routed to a soundcard and out an output, so I would like an amp that is voice signal activated. Has anyone found anything

I keep clicking on the WindowsNT link and it keeps extending the path name... is something wrong? thanks -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- r-devel mailing list -- Read http://www.ci.tuwien.ac.at/~hornik/R/R-FAQ.html Send "info", "help", or "[un]subscribe" (in the "body", not the subject !) To:

Hey gang. Jed noticed an issue with the ''dependency''/''dependencies'' macro the other day when working on the Collective wiki. Namely, if you make RedCloth a dependency Merb gets a little cranky. I think I have this figured out when doing some mods to Collective today too. However, before I go trying to fix this in Merb, I wanted to run this by the community.

Whoops. Sorry about that. I wasn't supposed to actually have that as a reply, it was meant to be another top-level post. To summarise, wrc in the Mandriva wine-1.1.0 RPM available from Sourceforge conflicts with the name of "wrc" in openwatcom, which is also a Win32 resource compiler. Cheers, The Viking, Flying Brick Systems.

The AstLinux Team has released 1.2.0. All current users are encouraged to upgrade as this release addresses the bash "ShellShock" bug. New in 1.2.0: * New Linux Kernel 3.2.x * "igb" ethernet driver for Intel Atom C2000 * Enable AES-NI support * New "sip-user-agent" firewall plugin * New versions of Asterisk 11 and 1.8 * Bash "ShellShock" security fixes A