similar to: Maybe OT - routing calls in PSTN

Hello: I am experiencing long delays, minutes not seconds, after issuing sip reload or /etc/init.d/asterisk restart commands. When reloading Asterisk, for the first minute or more, sip show registry says there is no such command. When sip show registry begins to provide information, registration can take another 3-4 minutes. Sometimes, timeouts occur as well, and sometimes these timeouts

Hello List, Since I'm looking for a new VoIP provider for US origination/termination, I will very appreciate if you can chare your experience with Flowroute, Vitelity and Voip.ms Thanks in advance! Elder D. Arohuanca dCAP 1497 Lima - Peru -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, Inspired by a recent rant about one particular provider, I am getting very curious about something I've never mastered. I'd like someone to explain this here or at least post a link or two that can educate me and probably countless others who have no knowledge in this area. I'm sure there are several of you reading this that know all about the subject. What are the various

Hi, I am requesting for a E1 connection from my telco. They are asking if I want DSS1 or SS7, and I am stuck here. Could someone tell me the difference between the two? How should I decide which one to use? Thanks in advance for your help. Mark -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have a customer installation with an Adtran DS3 mux. The DS1's go into my Asterisk servers that run IVR/Call recorders. The DS3 provider is Qwest, and they tell me that they routinely drop the DS3 service to redundant back-up's and that this is a common practice that happens thousands of times to DS3 lines daily across the US without any service interruptions. They say that the

Not sure why, but Vitelity changed the settings to IP based authentication on me. Here's the new sip.conf settings they sent me. type=friend dtmfmode=auto host=64.2.142.93 allow=all nat=yes canreinvite=no trustrpid=yes sendrpid=yes When I use these settings to originate calls using the sip.conf they sent me, everything works. Action: Originate ActionID: S8 Channel:

I know that the wiki has an extensive list of European VoIP providers out there....but there's so many that it's kind of hard to sort through. So I was wondering if anyone could recommend some reliable SIP/IAX termination providers in Europe? Something like VoicePulse Connect, NuFone, Vitelity, or Junction Networks based out of Europe. I really don't trust a US VoIP company for

Hi All; I do not know if anyone faced such case in dealing with open vpn (as we need it for fring to be used from the mobile: Which mobile can be used to install the open vpn client on it, so we can use it to do a vpn channel with the server that has open vpn server? Regards Bilal

Hi, I've sucessfully completed an Openser 1.3.2 + Mediaproxy 1.9.1 + Asterisk 1.4 + CDRTool with freeradius telephony system. Asterisk is used only for voice mail and redirectioning calls. Every calls should pass through mediaproxy so that i can account them. The goal was to create a simple prototype of what could be a VoIP provider. Now i need to dimensioning this system to work

I have a block of DID's that I ported to Vitelity about 7 days ago. The problem is if a POTS caller dials into the system, his dtmf is not heard at READ() or Background() while a prompt is played. After the prompt is finished, then dtmf is heard. I've been working with their support, but it still not resolved. SIP callers are not effected. Yesterday, I purchased a DID from

Is there a way to limit simultaneous calls. I like to limit simultaneous outgoing calls as more than few simulataneous calls are charged by my voip providers. However, I do not want to have any such restriction for internal calls. Thanks Jim

Hi all, I am trying to send an extra header in SIP INVITE Message , i.e (email="me at me.com") but when I check the Message at the target that header is not there So I is Askterisk altering the Message and Is there away to include extra headers for SIP INVITE Message? Thank u

Almost all DID providers refer to XO and L3. Are they the only sources for DIDs in USA and everybody has to go to them? Could someone explain how exactly it works? Thanks -- Zeeshan A Zakaria -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070531/170b14cb/attachment.htm

I've got the ztdummy kernel module loaded and seem to have all the desired prerequisites in place, but Asterisk never seems to compile with MeetMe() application support enabled, nor does there appear to be a module I am failing to load that would contain this application. Is there something really obvious I am missing? Thanks, -- Alex Balashov Evariste Systems Web :

Thank you Joshua. I will make the modifications this morning and give it a try. Have a great day! Dan -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Joshua Colp Sent: Wednesday, December 10, 2014 7:27 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] PJSIP

Just an FYI for Digium. I received a mailing today from you guys which was nice. The price of mailing was ~$1.60 and inside was an inflatable beach ball. Cool, but I tried to blow up the beach ball and the the seam where the part opens to inflate the ball was not connected to the ball whatsoever, so it went right in the trash. I wonder if the sick heat had anything to do with it, was mine just

hello all, i have 2 asterisk boxes on that 1 have public IP Address and another is only have local IP address now on public IP there are some 7 DID forwarded , now i want to forward 3 DID out of 7 DID to local machine we called server B , I know there are DIal , and Switch statement in asterisk , but is there any other convenient way to do this. because if call ratio is high then my call legs

Really? Me? Oh Pavel! I would be inestimably honoured. On 04/27/2012 01:55 AM, Pavel Ismailov wrote: > Hello! > > My name is Pavel Ismailov > and I`m CEO of www.flashphoner.com project. > > We noticed that you quite active in Asterisk-user > mail list, and would like to offer you buy signature > in your messages for some monthly price. > > Is it interested for

My latency is kind of high and the voice delay is noticeable. The Asterisk server is on a dedicated host outside of the network. I am performing PAT/NAT using a Cisco router. ns1*CLI> sip show peers Name/username Host Dyn Nat ACL Port Status vitel-outbound/rsreese 64.2.142.22 5060 Unmonitored vitel-inbound/rsreese 64.2.142.116

I made a little write-up that attempts to synthesise a lot of the information out there about how to get HylaFAX working with Asterisk by way of IAXmodem for inbound faxing: http://blog.evaristesys.com/?p=24 Of course, there are bound to be some things I've left out or are grossly in need of correction. So, before I link it off the voip-wiki I am extremely eager to solicit the input of