similar to: Format ulaw|h ?

Hello all I've discovered that SIP channels sometimes get stuck in *. I've read some posts from Fri 29 Aug 2003 which mentions this issue, but there doesn't seem to be any final answers I don't know if this is related to the 0001604 bug? Below is a list from one of the incidents: I know the (d) means that it is scheduled for destruction but the 10.1.1.45 channel hasn't

I am using a2billing as calling card platform with asterisk 1.2.17. After running for several days, if I issue 'sip show channels' command, I got a lot of dead sip channels although 'show channels' command only show 5 channels. What cause these dead channels? How can I clean out these dead channels? Will they pose any problem to my * server if left alone? What does this (d) mean?

Hi, one of the sip-extensions we created always returns busy when someone tries to call the phone. The extension itself can place calls. We're using snom360 phones with the latest firmware. On every one of those phones when we register with the sip-extension, we've experienced the same problem. This is the output from sip show channels: Peer User/ANR Call ID Seq

Can someone recommend the best way to view current calls in progress on the Asterisk console? Neither the 'show channels' or 'sip show channels' commands are easy to read. hestia*CLI> show channels Channel Location State Application(Data) SIP/2944093-f9e2 (None) Up Bridged Call(SIP/2944079-e7f2) SIP/2944079-e7f2

We are using G711 for phones to talk to Asterisk and G729 licenses at asterisk to talk to ITSP Could you please suggest transcoder to use from G711 and G729 and which is comptible with Asterisk. We will like to avoid using TDM if possible Also i remember that initially we didn't have G729 and were using only 711 for with vicidial but then also we had same problems. at that time it was only 2

Hi, I am using Trxibox 2.6 latest ISO install. Following is the output of : "sip show channels" [trixbox ~]# /usr/sbin/asterisk -rx "sip show channels" Peer User/ANR Call ID Seq (Tx/Rx) Format Hold Last Message 212.53.40.40 0218245 6cfb845d050 09011/00000 0x0 (nothing) No 192.168.1.116 (None) YTc4ZmM3NjV 00101/00006 0x0

Hi all, I have a question regarding pending (zombie) SIP sessions: on Asterisk CLI, with command 'sip show channels' , I see two channels in use with callID and other infos detailed; also 'sip show inuse' give me same result (in terms of channels usage): Peer User/ANR Call ID Seq (Tx/Rx) Format Hold Last Message xx.xx.xx.79 209

'morning everybody, Here is the setup: 5126800422 called 3035 (3035 is a Cisco 7960). The call is g729. 3035 presses 'Conference' on her phone and calls 8327549222. This call is ulaw. (65.72.107.2 is our Cisco 7206 SIP->PRI gateway.) asterisk*CLI> sip show channels Peer User/ANR Call ID Seq (Tx/Rx) Format 65.72.107.2 8327549222 1758081f67e

Hi All, I'm having problem with IAX, I'm trying to connect to speex.co.il from asterisk using: register => username:password@speex.dyndns.org and I cant get it to work. Maybe someone who already got this to work will help... When dialing my speex extension I see the next output from consol: IAX2 Debugging Enabled *CLI> Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno:

My sip show channels shows some channels active that I can not make sense out of, and they have been that way for days, so I am pretty sure they are orphans. Is there a way to show active CALLS (instead of channels) to try and determine the source? Does the output below provide any clues as to why these channels might show active? Anyone aware of related bugs? The #'s indicate original

Hi! I'm trying an asterisk-FWD connection. I'm using X-Lite OR SIPPS as the IP phone. I configured the X-Lite and SIPPS to use GSM codec. Whe I call FWD, I get this info on the channels when the call has not been stablished yet: sip show channels Peer User/ANR Call ID Seq (Tx/Rx) Lag Jitter Format 192.246.69.223 613 1770bf3430d 00102/00000

https://bugzilla.mindrot.org/show_bug.cgi?id=2634 Bug ID: 2634 Summary: KAKI KAKA PASS 1-855(338-0710) || outlook technical support number / (1 855)338+0710 outlook customer service Number Outlook Tech Support Number Product: Portable OpenSSH Version: 7.2p2 Hardware: All OS: All

Hi all, i'm trouble with codec setup on an asterisk machine 1.4.18 and some Thomson ST2030 as extensions. In the users.conf file for internal extension i have: disallow=all allow=g729 allow=alaw allow=ulaw Without any codec installed (i mean with original g729 of asterisk) all go fine, calling from an extension to one other: Peer User/ANR Call ID Seq (Tx/Rx) Format

I made the post below earlier today. I'v since removed all NAT from the equation and the problem still persists. Basically I am trying to transfer a call. The transferring phone sends a REFER message to asterisk with a call id that Asterisk doesn't know about. Surely, surely.... someone else must have seen this? hermes*CLI> sip show channels Peer User/ANR Call ID

Dear Geskus, I want to develop a prediction model. I followed your paper and analysed thro' weighted coxph approach. I can develop nomogram based on the final model also. But I do not know how to do internal validation of the model and subsequently obtain calibration plot. Is it possible to use Wolbers et al Epid 2009 approach 9 (R code for internal validation and calibration) . It is

Hi all, I have a Cisco 1760 gateway and and Cisco 7960 VoIP phone running via Asterisk. Both are running g711A codecs and SIP. On inbound calls I get a native bridge, however on outbound calls I never get a native bridge. With other SIP gateways I do get a native bridge on the outbound call. My sip.conf is as follows: [cisco1760] type=friend context=incoming host=192.168.0.55 insecure=yes nat=no

HI All, I am new to asterisk. i want to make outbound calls from asterisk. I tried with many times with the given settings but in vain This is my scenario: I have a *user A* who has registered with sip server(ONDO), I made asterisk to register as a sip client with ONDO, I want to make a call to user A from an extension. My configurations sip.config [general] context=default

Hi All, Trying to get familiar with dplyr so I have a basic question: How to summarise sum(Values) per species, maintaining Code column (each species has a Code): Species Values Code 1 Acanthocybium solandri 33 LC 2 Makaira nigricans 20 VU 3 Makaira nigricans 20 VU 4. Makaira nigricans

Dear Raja, A Fine and Gray model can be fitted using the standard coxph function with weights that correct for right censoring and left truncation. Hence I guess any function that allows to perform stepwise regression with coxph should work. See e.g. my article in Biometrics https://doi.org/10.1111/j.1541-0420.2010.01420.x, or the vignette "Multi-state models and competing risks" in the

192.168.1.107 199 6bd3fb49505 00102/00000 ulaw No Tx: ACK 192.168.0.100 110 5c5a4953-65 00101/00005 ulaw Yes Rx: ACK Those channels are stuck talking to each other. The phones are disconnected yet that connection remains. I can clear w/ a restart obviously, but is there any way to tear down a call like that from the CLI? Bill -------------- next