similar to: Decline message

Hello Users , I Posted to mailing list, No one is replying My issues, My Issue is No Audio when Openser and Asterik integrated in Same LAN , When UAC are Behind the NAT, With out the Asterisk integration Behind the NAT is working Fine. SIP port and RTP ports are forwarded into router to OpenSER System only. openser.cfg listen=192.168.2.11 alias=sip.hyperion.com # Invite Section if ( method==

Though I've had implementations of Asterisk, I havent encountered this one yet, so i'd like to seek your advise if this possible. I would want asterisk to be stand between the dialer the destination. The dialer will now dial asterisk access number. Asterisk will acknowledge user by using CallerID and check against its database for authentication and then sends out a DTMF A tone for ?

Hello All. I am having some trouble with call transfers when asterisk is the 2nd party called and I hope to benefit from your experience. I want to use asterisk for call park/pickup and have configured openser to relay calls made to ruri 700-720 to asterisk running on localhost:5069 Call flow: phone A calls phone B (both phones are polycom) Phone B answers then phone b

Hi all, I need to register asterisk on an OpenSIPS SIP Proxy...The Registration is OK but my asterisk is sending OPTIONS packets to OpenSIPS and the SIP Proxy is not replying back...The issue is the UNKNOWN username that reside in the OPTIONS packet as you can see in the captured packets as you can see below: 1. U Asterisk_IP:5060 -> OPENSIPS_IP:5060 2. OPTIONS sip:OPENSIPS_IP

I have several sip stations that on a that are on a nat'd network behind a nice friend firewall.. no audio path issues, 2 way audio works, etc,etc,etc. However, I can't get any of my phones to Transfer or Blind Transfer.. I search and search, and well, just about gone nuts on this one. Here is sip debug from pressing "transfer->blind->dial dest->Dial Key" (note both

Hi all, I try to make a call from my Openser(SIP Proxy) to the asterisk in different machine. I use my asterisk as a trunking gateway. I can make a call from my openser to some trunking gateway such as my cisco 5300 or welltech 5250. In the same method, I try to make a call to asterisk ( sip listen on udp 5060 ) I use ngrep on my asterisk machine and list as below. But I can't find any sip

I'm taking the liberty to announce this event on the Asterisk mailing list, as Asterisk and OpenSER form a valuable combination in SIP architectures. The second edition of OpenSER Summit will take place in San Jose, USA ,on the 17th of March, 2008, during VonX Spring 2008 pre-conference events. This is the first US edition of the OpenSER Summit - to learn more about the agenda and layout of

Hi to all. I'm trying to use meetme on asterisk 1.4.22.1. On a debian i've compiled (as i need h323 support) openh323_v1_18_0 pwlib_v1_10_0 dahdi-linux-2.1.0.3 dahdi-tools-2.1.0.2 asterisk-1.4.22.1 All works fine, dahdi status is: asterik:/data/programmi# /etc/init.d/dahdi status ### Span 1: DAHDI_DUMMY/1 "DAHDI_DUMMY/1 (source: RTC) 1" (MASTER) asterik:/data/programmi#

Hi, I am trying to integrate asterisk with openser for a simple call. I am facing some issues with Asterisk. Below is the explanation: I have a UA1 sending invite to UA2 through Openser and Asterisk with the below sequence. Sequence is UA1->OpenSER->Asterisk->Openser->UA2 When Asterisk gets the INVITE, the INVITE contains two Via headers, one of the UA1 and

Trying to find a solution to a sticky problem here. We have 3 OpenSER systems. Phones register with the OpenSER systems, and after they authenticate the user, pass the registration info using OpenSER's send() command to all Asterisk boxes sitting behind them. Each asterisk system then knows about every phone. For this to work, I had to turn off authentication in Asterisk for both

Hi, I am faced with this dilema of asterisk not sending an ACK after it receives 200 OK from OpenSER (which is a response to a reinvite request sent by asterisk. Here is my setup Carrier<->OpenSER<->Asterisk1<->Asterisk2 A user is connected with Asterisk1 (through the carrier and OpenSER). On certain dtmf events the call is forwarded to Asterisk2 using the Dial command.

Hi, Using openser 1.1.0-dev8 as a registrar/proxy in from of Asterisk. Recently I have been getting errors from Asterisk due to corrupted From: headers, which appear to be caused by uac_replace. Here is a section of the debug log: Mar 14 15:12:00 www1 /usr/sbin/openser[7933]: DBG:uac::restore_from_reply: removing <From: <sip:lenc_domain.com@sip.domain.com>;tag=635c3ce6 > Mar

Hi, does anybody know if asterisk can authenticate on a NOTIFY send to a peer. I use OpenSER as SIP-Proxy and asterisk as voicemail system with ODBC Support for voicemail-messages, voicemail-users and sip-peers/users. My SIP-Users register with OpenSER. Asterisk has two views on the OpenSER database for voicemail-users and sip-peers. Call-Routing, leaving voicemail-messages in database an MWI

Hi all, Is there a solution to solve this ? ASTERISK 1.2.4 || Internet===SER/OPENSER=====Nat==[private net] || sip agents rtpproxy/mediaproxy Sip agents use SER/OPENSER as an outbound sip proxy and asterisk as a registar server, pbx functions, ... SER/OPENSER look for domains in URI. if domains are handled by SER/OPENSER

Dear All, I have the following CPU info on my asterisk server: Linux switch1.domain.net 2.6.18-92.1.22.el5 #1 SMP Tue Dec 16 12:03:43 EST 2008 i686 i686 i386 GNU/Linux I need to install G729 on the asterisk server just to pass through and not for encoding...Which G729 package do you advice me to install? I tried several packages with no luck Regards -------------- next part -------------- An

Hi All, I am stuck with an issue in the Openser+Asterisk Forking. In this solution we are using Openser as the Registrar. Hence it will store all the contact bindings along with the q values for a given user, say ua1. The current setup is such that the INVITEs are sent to Asterisk by Openser and Asterisk sends out the INVITE. Now if ua1 is registered with two different contacts having

Sorry if this hit the list twice, sent out yesterday, but didn't see it show up. Hi All, Can Asterisk be used as a SIP proxy, blah, blah, blah??? I've glanced over questions like this through the years, with a good idea on what a SIP proxy is and what Asterisk is and IS NOT. I never really took the time to lab-up SER and test drive it to see what advantages might be gained from using

Suggestions on how to use Asterisk to collect CDRs from a OpenSER-based proxy / call routing setup? I need to get simple CDRs; not for detailed settlement/rating, but just for reconciliation with an ultimate TDM carrier just to make sure we only get billed for what we're actually using. I'd use the often-heralded approach of dumping a call from OpenSER into Asterisk and having it

This is a SER/Polycom question, but I hoped we may have some SER guru's here... I have a series of Polycom phones that are tying to register with OpenSER. The phone sends a REGISTER message, and OpenSER replies with Unauthorised (all normal). The phone re-sends the REGISTER with the credentials, and OpenSER sends Ok. Here's where it goes downhill. The polycom's appearance display

Hello Users openSER is sip proxy and registrar , Asterisk is as PBX, Conference and Voicemail servers, openSER and Asterisk are in the Same N/w Where As the UAC are in Behind the NAT, When Astetrisk is not integrated , UAC are in Behind the NAT is working, openSER is 192.168.2.5 Asterisk is 192.168.2.6 I'm just use rewritehost to asterisk server, UAC ----> openSER - - - ->