similar to: Zaptel and Solaris X86

I'm looking to build the zaptel drivers on a Solaris 10 X86 box. I've found the driver source code on https://svn.sunlabs.com/svn/solaris-asterisk but this source is posted along with Asterisk 1.2.7.1 Does anyone know of a fresher version? Is this code considered "somewhat ready for prime time use"? Thanks, Frank

I'm running Asterisk 1.2.13 on a Solaris 10 X86 box behind an IPCop firewall on a 5Mbps down/512 up cable connection. I'm having sound quality problems when users call in for voicemail and with music on hold. The sound is choppy and muffled while souding pretty good for calls inside the network. I'd appreciate some pointers as to where to start looking to improve things. I've

----- Original Message ----- From: "chris" <chris@fivestartel.com> To: "Frank Tarczynski" <ftarz@mindspring.com>; <seruser@iptel.org> Sent: Tuesday, July 26, 2005 9:54 AM Subject: Re: [Asterisk-Users] /bin/sh: build_tools/make_version_h: not found > hi Tzafrir > > any idea how we can fix this error? > > include/asterisk/strings.h:232: parse

Hello nice people :) I have been struggling with trying to get Zaptel from http://www.slimey.org/zaptel-solaris.tar.gz on a Solaris 5.11 VM I obtained from the OpenSolaris Website. I have tried installing all the necessary packages, yet I keep getting errors no matter if I try using the gcc available at sunfreeware.com OR the blastwave CSWgcc packages and GNU 'gmake' (as suggested

I'm running an AsteriskNow V1.7.1 with both a PSTN connection and fax machine. Both are connected to a DAHDI board. I'd like to route incoming PSTN fax calls to the extension of the fax machine and process non-fax calls through different dialplan.logic. What's the best way to go about doing this? I've looked into Fax for Asterisk, bit I'm not sure that I want it or NVFax

>Message: 11 >Date: Sun, 28 Aug 2005 11:46:29 +0800 >From: "chris" <chris@fivestartel.com> >Subject: [Asterisk-Users] error compiling on solaris 10 >To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> >Message-ID: <003a01c5ab83$149a9e30$650fa8c0@acid> >Content-Type: text/plain;

I'm looking for pointers towards building and running the zaptel drivers under Solaris 10. Can anyone help? Frank

I'm trying to set-up H.323 support under Asterisk. I built a recent CVS release and the ooh323c code from the asterisk-addons. Everything built and installed and the H.323 stuff loads OK when asterisk starts. What is the easiest way to check if the H.323 code is working? I've edited the h323.conf and extensions.conf files but I'm sure that things aren't right. I've

I've built Asterisk from recent CVS sources on a Solaris 10 X86 box. I tweaked the makefile to get the build to run using gcc. And most recently ran into va_args problems with new code in asterisk/utils.c. It seems to run OK and register with my VoIP provider, but I'm still having trouble setting-up connections to my Sipura SPA-3000. Does anyone have some experience under S10 X86?

I'm having a problem with asterisk-1.4.4 dumping core under Solaris 10 with a SIGSEGV error. gdb gives this stack trace: #0 0xfebd4d0c in strlen () from /usr/lib/libc.so.1 #1 0xfec2a386 in _ndoprnt () from /usr/lib/libc.so.1 #2 0xfec2d4bb in vsnprintf () from /usr/lib/libc.so.1 #3 0x080e86de in ast_dynamic_str_thread_build_va (buf=0x8172763, max_len=0, ts=0x81482a0, append=0,

I'm having a problem with my IAXy not always connecting to my Asterisk box. When I pick-up the phone plugged in to the IAXy I get a busy signal. I have to hang-up the phone and wait a few seconds after the orange LED goes out and then try again. When this happens I don't see any connection attempts in the Asterisk -r output. When I do get the IAXy to connect to Asterisk I get a

I'm trying to get a MP-114 FXS/FXO gateway working with Asterisk. It registers fine and I can call between the MP-114 and other extensions, but I'm not having much luck with the FXO ports. syslog shows the problem to be in the MP-114 configuration. Can anyone help?

Hi, I encountered the following when i run the below command on my Solaris 8 x86 box: #ssh-keygen -t rsa1 -f /usr/local/etc/ssh_host_key -N "" I got the following error: Segmentation fault - core dumped Does anyone have any idea what is wrong? I am using pre-compiled packages downloaded from sunfreeware.com. Regards, Matthew This communication contains confidential or privileged

Dear R developers, we have currently a 'mysterious' test problem with one package that successfully passed the tests on all platforms, with the only exception of Solaris x86 where obviously one of our help examples breaks the CRAN test. As we don't own such a machine I want to ask about a possibility to run a few tests on such a system: r-patched-solaris-x86 An even more recent

Hello Since the Ports collection showed that there were more recent versions of Asterisk and Zaptel, I tried to compile/install Zaptel, but it fails, even after stopping Zaptel cleanly, and even after stopping Asterisk itself, so I decided to just reboot. Now, when I type "ztcfg -vv", I lose the SSH connection for a couple of minutes. ======= Dec 20 14:37:21 freebsd kernel: Zapata

> Message: 1 > Date: Tue, 15 May 2007 23:01:24 -0400 > From: Frank Tarczynski <ftarz at mindspring.com> > Subject: [asterisk-users] Asterisk 1.4.4 reproducibly dumps core on > Solaris 10 > To: asterisk-users at lists.digium.com > Message-ID: <464A7404.5000706 at mindspring.com> > Content-Type: text/plain; charset=ISO-8859-1; format=flowed > > I have

I am using Asterisk 1.2.13 with Zaptel 1.2.11, I used to have an old PBX connected to one port and the PRI connected to the other. I'm having serious stability issues with Asterisk on a box that has been rock solid previously. The old PBX died two months ago so one port on the TE210P is now unused but still configured. Also I'm afraid I have upgraded from Asterisk 1.2.9.1 and the old

All, I have upgraded by home machine from Fedora Core 5 (FC5) to the recent FC6 and am struggling to build Zaptel-1.2.10 and Asterisk-1.2.13 on the box... which is an Intep P4 2.8GHz HT processor box with 845 chipset, hence the kernel installed is 2.6.18-1.2798.fc6-i686 so we hve this: [root@gate zaptel-1.2.10]# uname -a Linux gate.tubby.org 2.6.18-1.2798.fc6 #1 SMP Mon Oct 16 14:54:20

Hello I'm trying to build the Zaptel ports on FreeBSD, but it fails: ========== # cd /usr/ports/misc/zaptel/ # make install ===> Building for zaptel-1.4.6_3 make -C zaptel all Warning: Object directory not changed from original /usr/ports/misc/zaptel/work/zaptel-bsd-1.4.6/zaptel cc -O2 -fno-strict-aliasing -pipe -Wall -D_KERNEL -DKLD_MODULE -std=c99 -nostdinc -I. -I@ -I@/contrib/altq

hey asterisk folk, i'm new to asterisk, but not to freebsd as i've been using it and developing on it for quite a few years. we're planning on deploying asterisk as part of a voip provider's service platform and naturally i'd rather be using freebsd instead of a linux based distro. as such, i am very, very excited that there is work going on towards porting the zaptel drivers